IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v14y2021i10p2903-d556583.html
   My bibliography  Save this article

Analysis of Thermodynamic Parameter Variability in a Chamber of a Furnace for Thermo-Chemical Treatment

Author

Listed:
  • Magda Joachimiak

    (Institute of Thermal Engineering, Poznan University of Technology, 60-965 Poznan, Poland)

Abstract

This paper presents results of research on unevenness of cylinder heating in a furnace for thermo-chemical treatment. Experimental research was conducted with respect to nitriding. Various heating speeds and settings of the fan operation in the furnace were considered. Boundary conditions were calculated in the form of temperature and the heat transfer coefficient (HTC) on the cylinder boundary in four planes along the cylinder length. Calculations were performed with the use of the inverse problem for non-linear and unsteady heat conduction equations. Boundary conditions from individual planes were compared with the mean value of them all. The variability of the calculated boundary conditions (temperature and HTC) along the cylinder length was investigated based on values of the absolute and relative differences for temperature and HTC. Estimates: mean value, mean value from the absolute value and the maximum values for the absolute and the relative differences of temperature and HTC were also calculated. Estimates were the measurements of the unevenness of cylinder heating in a furnace for thermo-chemical treatment. Based on the results of our research, it was found that an increase of the fan rotational speed from 50% to 100%, with the same heating speed, resulted in a significant leveling of temperature in the analyzed planes. The difference in temperature along the cylinder length was reduced from 6.8 °C to 3.3 °C. The increase of the heating speed from 5 °C/min to 10 °C/min resulted in an increase of the unevenness of the cylinder heating. Values of the absolute differences of temperature in the analyzed planes with reference to the mean temperature changed from an interval from −2.7 °C to 2.3 °C to a range from −4 °C to 5 °C. In processes with a heating speed greater than 5 °C/min, more intensive heating in the end part of the cylinder (close to the cylinder) was achieved than it was in other planes. It was proven by temperature values, which were higher, even, by 5.4 °C, and by HTC values, higher by 11.4 W/m 2 K, when compared with mean values. Obtained results can form the basis for nitriding process optimization.

Suggested Citation

  • Magda Joachimiak, 2021. "Analysis of Thermodynamic Parameter Variability in a Chamber of a Furnace for Thermo-Chemical Treatment," Energies, MDPI, vol. 14(10), pages 1-18, May.
    • Handle: RePEc:gam:jeners:v:14:y:2021:i:10:p:2903-:d:556583
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/14/10/2903/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/14/10/2903/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Wojciech Judt, 2020. "Numerical and Experimental Analysis of Heat Transfer for Solid Fuels Combustion in Fixed Bed Conditions," Energies, MDPI, vol. 13(22), pages 1-18, November.
    2. Beata Kurc & Piotr Lijewski & Łukasz Rymaniak & Paweł Fuć & Marita Pigłowska & Rafał Urbaniak & Bartosz Ciupek, 2020. "High-Energy Solid Fuel Obtained from Carbonized Rice Starch," Energies, MDPI, vol. 13(16), pages 1-18, August.
    3. Magdalena Jaremkiewicz & Dawid Taler & Piotr Dzierwa & Jan Taler, 2019. "Determination of Transient Fluid Temperature and Thermal Stresses in Pressure Thick-Walled Elements Using a New Design Thermometer," Energies, MDPI, vol. 12(2), pages 1-21, January.
    4. Dawid Taler & Tomasz Sobota & Magdalena Jaremkiewicz & Jan Taler, 2020. "Influence of the Thermometer Inertia on the Quality of Temperature Control in a Hot Liquid Tank Heated with Electric Energy," Energies, MDPI, vol. 13(15), pages 1-18, August.
    5. Magdalena Jaremkiewicz & Jan Taler, 2020. "Online Determining Heat Transfer Coefficient for Monitoring Transient Thermal Stresses," Energies, MDPI, vol. 13(3), pages 1-13, February.
    6. Magdalena Piasecka & Sylwia Hożejowska & Beata Maciejewska & Anna Pawińska, 2021. "Time-Dependent Heat Transfer Calculations with Trefftz and Picard Methods for Flow Boiling in a Mini-Channel Heat Sink," Energies, MDPI, vol. 14(7), pages 1-24, March.
    7. Sylwia Hożejowska & Magdalena Piasecka, 2020. "Numerical Solution of Axisymmetric Inverse Heat Conduction Problem by the Trefftz Method," Energies, MDPI, vol. 13(3), pages 1-14, February.
    8. Damian Joachimiak & Andrzej Frąckowiak, 2020. "Experimental and Numerical Analysis of the Gas Flow in the Axisymmetric Radial Clearance," Energies, MDPI, vol. 13(21), pages 1-13, November.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Damian Joachimiak, 2021. "Novel Method of the Seal Aerodynamic Design to Reduce Leakage by Matching the Seal Geometry to Flow Conditions," Energies, MDPI, vol. 14(23), pages 1-16, November.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Taler, Dawid & Dzierwa, Piotr & Kaczmarski, Karol & Taler, Jan, 2021. "Optimisation of heating and cooling of pressure thick-walled components operating in the saturated steam area," Energy, Elsevier, vol. 231(C).
    2. Magdalena Piasecka & Sylwia Hożejowska & Anna Pawińska & Dariusz Strąk, 2022. "Heat Transfer Analysis of a Co-Current Heat Exchanger with Two Rectangular Mini-Channels," Energies, MDPI, vol. 15(4), pages 1-19, February.
    3. Bartosz Ciupek & Wojciech Judt & Karol Gołoś & Rafał Urbaniak, 2021. "Analysis of Low-Power Boilers Work on Real Heat Loads: A Case of Poland," Energies, MDPI, vol. 14(11), pages 1-13, May.
    4. Taler, Dawid & Sobota, Tomasz & Jaremkiewicz, Magdalena & Taler, Jan, 2022. "Control of the temperature in the hot liquid tank by using a digital PID controller considering the random errors of the thermometer indications," Energy, Elsevier, vol. 239(PE).
    5. Taler, Dawid & Dzierwa, Piotr & Kaczmarski, Karol & Taler, Jan, 2022. "Increase the flexibility of steam boilers by optimisation of critical pressure component heating," Energy, Elsevier, vol. 250(C).
    6. Magdalena Piasecka & Sylwia Hożejowska & Beata Maciejewska & Anna Pawińska, 2021. "Time-Dependent Heat Transfer Calculations with Trefftz and Picard Methods for Flow Boiling in a Mini-Channel Heat Sink," Energies, MDPI, vol. 14(7), pages 1-24, March.
    7. Magdalena Piasecka & Kinga Strąk, 2021. "Characteristics of Refrigerant Boiling Heat Transfer in Rectangular Mini-Channels during Various Flow Orientations," Energies, MDPI, vol. 14(16), pages 1-30, August.
    8. Jan Taler & Paweł Ocłoń & Marcin Trojan & Abdulmajeed Mohamad, 2019. "Selected Papers from the XI International Conference on Computational Heat, Mass and Momentum Transfer (ICCHMT 2018)," Energies, MDPI, vol. 12(12), pages 1-3, June.
    9. Li Peng & Hongjun Wu & Qianjun Mao, 2022. "Visualizing Experimental Study of the Effect of Inclination Angle on the Melting Performance for an Energy Storage Tank," Energies, MDPI, vol. 15(19), pages 1-11, October.
    10. Jerzy Okrajni & Mariusz Twardawa & Krzysztof Wacławiak, 2021. "Impact of Heat Transfer on Transient Stress Fields in Power Plant Boiler Components," Energies, MDPI, vol. 14(4), pages 1-19, February.
    11. Joseph Rendall & Fernando Karg Bulnes & Kyle Gluesenkamp & Ahmad Abu-Heiba & William Worek & Kashif Nawaz, 2021. "A Flow Rate Dependent 1D Model for Thermally Stratified Hot-Water Energy Storage," Energies, MDPI, vol. 14(9), pages 1-17, May.
    12. Mohsen Tadi & Miloje Radenkovic, 2021. "Non-Iterative Solution Methods for Cauchy Problems for Laplace and Helmholtz Equation in Annulus Domain," Mathematics, MDPI, vol. 9(3), pages 1-14, January.
    13. Ding, Haixu & Tang, Jian & Qiao, Junfei, 2023. "Dynamic modeling of multi-input and multi-output controlled object for municipal solid waste incineration process," Applied Energy, Elsevier, vol. 339(C).
    14. Magdalena Piasecka & Beata Maciejewska & Paweł Łabędzki, 2020. "Heat Transfer Coefficient Determination during FC-72 Flow in a Minichannel Heat Sink Using the Trefftz Functions and ADINA Software," Energies, MDPI, vol. 13(24), pages 1-25, December.
    15. Magdalena Piasecka, 2023. "Heat and Mass Transfer Issues in Mini-Gaps," Energies, MDPI, vol. 16(16), pages 1-6, August.
    16. Damian Joachimiak, 2021. "Novel Method of the Seal Aerodynamic Design to Reduce Leakage by Matching the Seal Geometry to Flow Conditions," Energies, MDPI, vol. 14(23), pages 1-16, November.
    17. Fernanda Mitchelly Vilas Boas & Luiz Eduardo Borges-da-Silva & Helcio Francisco Villa-Nova & Erik Leandro Bonaldi & Levy Ely Lacerda Oliveira & Germano Lambert-Torres & Frederico de Oliveira Assuncao , 2021. "Condition Monitoring of Internal Combustion Engines in Thermal Power Plants Based on Control Charts and Adapted Nelson Rules," Energies, MDPI, vol. 14(16), pages 1-17, August.
    18. Magdalena Piasecka & Beata Maciejewska & Artur Piasecki, 2023. "Heat Transfer Calculations during Flow in Mini-Channels with Estimation of Temperature Uncertainty Measurements," Energies, MDPI, vol. 16(3), pages 1-19, January.
    19. Sun Kyoung Kim, 2021. "Influence of Errors in Known Constants and Boundary Conditions on Solutions of Inverse Heat Conduction Problem," Energies, MDPI, vol. 14(11), pages 1-20, June.
    20. Dawid Taler & Tomasz Sobota & Magdalena Jaremkiewicz & Jan Taler, 2020. "Influence of the Thermometer Inertia on the Quality of Temperature Control in a Hot Liquid Tank Heated with Electric Energy," Energies, MDPI, vol. 13(15), pages 1-18, August.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:14:y:2021:i:10:p:2903-:d:556583. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.