IDEAS home Printed from https://ideas.repec.org/a/eee/energy/v320y2025ics0360544225008151.html
   My bibliography  Save this article

Effect of polyethylene glycol (PEG) 600 as ignition improver on performance and combustion characteristics of hydrous bioethanol under CI engine condition

Author

Listed:
  • Zegarra Sánchez, Fernando
  • Carneiro, Maria Luisa N.M.
  • Moura de Souza Junior, Jorge Ricardo
  • Pradelle, Florian
  • Turkovics, Franck
  • Nohra Chaar Pradelle, Renata
  • Leal Braga, Sergio

Abstract

Ethanol is widely used in spark ignition (SI) engines, but its application in compression ignition (CI) engines is limited by its low cetane number, necessitating the use of additives like cetane improvers. This study evaluates, for the first time, the performance of polyethylene glycol 600 (PEG 600) as an ignition improver for bioethanol in a CI automotive engine, based on laboratory-scale findings. Hydrous bioethanol with 10% (HEPEG10) and 15% (HEPEG15) PEG 600 by weight was tested as a diesel substitute under two compression ratios (CR) of 20:1 and 25:1. The study varied the start of injection (SOI) and throttle positions, measuring key performance parameters including power, efficiency, maximum pressure, indicated mean effective pressure (IMEP), heat release, and ignition delay. The results indicated that PEG 600 could be a viable additive for bioethanol. HEPEG15 demonstrated more stable combustion than diesel at higher loads. Specifically, at 2280 rpm and CR 20:1, HEPEG15 achieved an 8% higher efficiency compared to diesel, with 13 % lower maximum pressure and 33% lower IMEP covariance. At CR 25:1, the additized bioethanol performed better across all load conditions, with HEPEG15 showing a 9% higher efficiency than diesel. At CR 20:1, the additized bioethanol only outperformed diesel at higher loads. Overall, while additized bioethanol exhibited lower efficiency at lower loads and higher maximum pressure, it provided better combustion performance when the SOI was advanced close to top dead center, though this might impact engine integrity and durability.

Suggested Citation

  • Zegarra Sánchez, Fernando & Carneiro, Maria Luisa N.M. & Moura de Souza Junior, Jorge Ricardo & Pradelle, Florian & Turkovics, Franck & Nohra Chaar Pradelle, Renata & Leal Braga, Sergio, 2025. "Effect of polyethylene glycol (PEG) 600 as ignition improver on performance and combustion characteristics of hydrous bioethanol under CI engine condition," Energy, Elsevier, vol. 320(C).
    • Handle: RePEc:eee:energy:v:320:y:2025:i:c:s0360544225008151
    DOI: 10.1016/j.energy.2025.135173
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0360544225008151
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.energy.2025.135173?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to

    for a different version of it.

    References listed on IDEAS

    as
    1. Chollacoop, Nuwong & Saisirirat, Peerawat & Sukkasi, Sittha & Tongroon, Manida & Fukuda, Tuenjai & Fukuda, Atsushi & Nivitchanyong, Siriluck, 2013. "Potential of greenhouse gas emission reduction in Thai road transport by ethanol bus technology," Applied Energy, Elsevier, vol. 102(C), pages 112-123.
    2. Imran, A. & Varman, M. & Masjuki, H.H. & Kalam, M.A., 2013. "Review on alcohol fumigation on diesel engine: A viable alternative dual fuel technology for satisfactory engine performance and reduction of environment concerning emission," Renewable and Sustainable Energy Reviews, Elsevier, vol. 26(C), pages 739-751.
    3. Shahir, S.A. & Masjuki, H.H. & Kalam, M.A. & Imran, A. & Fattah, I.M. Rizwanul & Sanjid, A., 2014. "Feasibility of diesel–biodiesel–ethanol/bioethanol blend as existing CI engine fuel: An assessment of properties, material compatibility, safety and combustion," Renewable and Sustainable Energy Reviews, Elsevier, vol. 32(C), pages 379-395.
    4. Rajesh Kumar, B. & Saravanan, S., 2016. "Use of higher alcohol biofuels in diesel engines: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 60(C), pages 84-115.
    5. Monir, Minhaj Uddin & Aziz, Azrina Abd & Khatun, Fatema & Yousuf, Abu, 2020. "Bioethanol production through syngas fermentation in a tar free bioreactor using Clostridium butyricum," Renewable Energy, Elsevier, vol. 157(C), pages 1116-1123.
    6. La Rovere, Emilio Lèbre & Pereira, André Santos & Simões, André Felipe, 2011. "Biofuels and Sustainable Energy Development in Brazil," World Development, Elsevier, vol. 39(6), pages 1026-1036, June.
    7. Pradelle, Florian & Leal Braga, Sergio & Fonseca de Aguiar Martins, Ana Rosa & Turkovics, Franck & Nohra Chaar Pradelle, Renata, 2019. "Performance and combustion characteristics of a compression ignition engine running on diesel-biodiesel-ethanol (DBE) blends – Potential as diesel fuel substitute on an Euro III engine," Renewable Energy, Elsevier, vol. 136(C), pages 586-598.
    8. Bonenkamp, T.B. & Middelburg, L.M. & Hosli, M.O. & Wolffenbuttel, R.F., 2020. "From bioethanol containing fuels towards a fuel economy that includes methanol derived from renewable sources and the impact on European Union decision-making on transition pathways," Renewable and Sustainable Energy Reviews, Elsevier, vol. 120(C).
    9. Emilio Lebre La Rovere & Andre Santos Pereira & Andre Felipe Simoes, 2011. "Biofuels and Sustainable Energy Development in Brazil," Post-Print hal-00715546, HAL.
    10. Kumar, Satish & Cho, Jae Hyun & Park, Jaedeuk & Moon, Il, 2013. "Advances in diesel–alcohol blends and their effects on the performance and emissions of diesel engines," Renewable and Sustainable Energy Reviews, Elsevier, vol. 22(C), pages 46-72.
    11. Shahabuddin, M. & Liaquat, A.M. & Masjuki, H.H. & Kalam, M.A. & Mofijur, M., 2013. "Ignition delay, combustion and emission characteristics of diesel engine fueled with biodiesel," Renewable and Sustainable Energy Reviews, Elsevier, vol. 21(C), pages 623-632.
    12. Yu, Yusong, 2019. "Experimental study on effects of ethanol-diesel fuel blended on spray characteristics under ultra-high injection pressure up to 350 MPa," Energy, Elsevier, vol. 186(C).
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Yusri, I.M. & Mamat, R. & Najafi, G. & Razman, A. & Awad, Omar I. & Azmi, W.H. & Ishak, W.F.W. & Shaiful, A.I.M., 2017. "Alcohol based automotive fuels from first four alcohol family in compression and spark ignition engine: A review on engine performance and exhaust emissions," Renewable and Sustainable Energy Reviews, Elsevier, vol. 77(C), pages 169-181.
    2. Ghadikolaei, Meisam Ahmadi & Wong, Pak Kin & Cheung, Chun Shun & Ning, Zhi & Yung, Ka-Fu & Zhao, Jing & Gali, Nirmal Kumar & Berenjestanaki, Alireza Valipour, 2021. "Impact of lower and higher alcohols on the physicochemical properties of particulate matter from diesel engines: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 143(C).
    3. Odziemkowska, Małgorzata & Matuszewska, Anna & Czarnocka, Joanna, 2016. "Diesel oil with bioethanol as a fuel for compression-ignition engines," Applied Energy, Elsevier, vol. 184(C), pages 1264-1272.
    4. Norhidayah Mat Taib & Mohd Radzi Abu Mansor & Wan Mohd Faizal Wan Mahmood, 2019. "Modification of a Direct Injection Diesel Engine in Improving the Ignitability and Emissions of Diesel–Ethanol–Palm Oil Methyl Ester Blends," Energies, MDPI, vol. 12(14), pages 1-21, July.
    5. Tamilselvan, P. & Nallusamy, N. & Rajkumar, S., 2017. "A comprehensive review on performance, combustion and emission characteristics of biodiesel fuelled diesel engines," Renewable and Sustainable Energy Reviews, Elsevier, vol. 79(C), pages 1134-1159.
    6. Mofijur, M. & Masjuki, H.H. & Kalam, M.A. & Ashrafur Rahman, S.M. & Mahmudul, H.M., 2015. "Energy scenario and biofuel policies and targets in ASEAN countries," Renewable and Sustainable Energy Reviews, Elsevier, vol. 46(C), pages 51-61.
    7. Alexandre Bevilacqua Leoneti & Valquiria Aragão-Leoneti & Simone Vasconcelos Ribeiro Galina & Geciane Silveira Porto, 2017. "The methylic versus the ethylic route: considerations about the sustainability of Brazilian biodiesel production," Environment, Development and Sustainability: A Multidisciplinary Approach to the Theory and Practice of Sustainable Development, Springer, vol. 19(2), pages 637-651, April.
    8. Gabisa, Elias W. & Gheewala, Shabbir H., 2020. "Can substitution of imported gasoline by locally produced molasses ethanol in Ethiopia be sustainable? An eco-efficiency assessment," Renewable and Sustainable Energy Reviews, Elsevier, vol. 123(C).
    9. Kirsten Halsnæs & Amit Garg & John Christensen & Helene Føyn & Maryna Karavai & Emilio Rovere & Matthew Bramley & Xianli Zhu & Catherine Mitchell & Joyashree Roy & Kanako Tanaka & Hidefumi Katayama & , 2014. "Climate change mitigation policy paradigms—national objectives and alignments," Mitigation and Adaptation Strategies for Global Change, Springer, vol. 19(1), pages 45-71, January.
    10. Doppalapudi, A.T. & Azad, A.K. & Khan, M.M.K., 2023. "Advanced strategies to reduce harmful nitrogen-oxide emissions from biodiesel fueled engine," Renewable and Sustainable Energy Reviews, Elsevier, vol. 174(C).
    11. Dias de Oliveira, Marcelo Eduardo & Moraes, Sergio Oliveira, 2017. "Modeling approaches for agricultural N2O fluxes from large scale areas: A case for sugarcane crops in the state of São Paulo - Brazil," Agricultural Systems, Elsevier, vol. 150(C), pages 1-11.
    12. Reymond, Mathias, 2012. "Measuring vulnerability to shocks in the gas market in South America," Energy Policy, Elsevier, vol. 48(C), pages 754-761.
    13. Che Mat, Sharzali & Idroas, M.Y. & Teoh, Y.H. & Hamid, M.F., 2019. "Optimisation of viscosity and density of refined palm Oil-Melaleuca Cajuputi oil binary blends using mixture design method," Renewable Energy, Elsevier, vol. 133(C), pages 393-400.
    14. De Oliveira, Fernando C. & Lopes, Thiago S.A. & Parente, Virginia & Bermann, Celio & Coelho, Suani T., 2019. "The Brazilian social fuel stamp program: Few strikes, many bloopers and stumbles," Renewable and Sustainable Energy Reviews, Elsevier, vol. 102(C), pages 121-128.
    15. M, Vinod Babu & K, Madhu Murthy & G, Amba Prasad Rao, 2017. "Butanol and pentanol: The promising biofuels for CI engines – A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 78(C), pages 1068-1088.
    16. Julia Szulecka, 2019. "Towards Sustainable Wood-Based Energy: Evaluation and Strategies for Mainstreaming Sustainability in the Sector," Sustainability, MDPI, vol. 11(2), pages 1-21, January.
    17. Yang, Jun & Wang, Xiaobing & Ma, Hengyun & Bai, Junfei & Jiang, Ye & Yu, Hai, 2014. "Potential usage, vertical value chain and challenge of biomass resource: Evidence from China’s crop residues," Applied Energy, Elsevier, vol. 114(C), pages 717-723.
    18. Pan, Mingzhang & Zheng, Zeyuan & Huang, Rong & Zhou, Xiaorong & Huang, Haozhong & Pan, Jiaying & Chen, Zhaohui, 2019. "Reduction in PM and NOX of a diesel engine integrated with n-octanol fuel addition and exhaust gas recirculation," Energy, Elsevier, vol. 187(C).
    19. Paola Perez-Aleman & Flavia Chaves Alves, 2017. "Reinventing industrial policy at the frontier: catalysing learning and innovation in Brazil," Cambridge Journal of Regions, Economy and Society, Cambridge Political Economy Society, vol. 10(1), pages 151-171.
    20. Mercure, J.-F. & Paim, M.A. & Bocquillon, P. & Lindner, S. & Salas, P. & Martinelli, P. & Berchin, I.I. & de Andrade Guerra, J.B.S.O & Derani, C. & de Albuquerque Junior, C.L. & Ribeiro, J.M.P. & Knob, 2019. "System complexity and policy integration challenges: The Brazilian Energy- Water-Food Nexus," Renewable and Sustainable Energy Reviews, Elsevier, vol. 105(C), pages 230-243.

    More about this item

    Keywords

    ;
    ;
    ;
    ;
    ;

    Statistics

    Access and download statistics

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:energy:v:320:y:2025:i:c:s0360544225008151. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.journals.elsevier.com/energy .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.