IDEAS home Printed from https://ideas.repec.org/a/eee/energy/v239y2022ipds0360544221024646.html
   My bibliography  Save this article

Performance improvement of supercritical carbon dioxide power cycle at elevated heat sink temperatures

Author

Listed:
  • Muhammad, Hafiz Ali
  • Cho, Junhyun
  • Cho, Jongjae
  • Choi, Bongsu
  • Roh, Chulwoo
  • Ishfaq, Hafiz Ahmad
  • Lee, Gilbong
  • Shin, Hyungki
  • Baik, Young-Jin
  • Lee, Beomjoon

Abstract

The supercritical carbon dioxide power cycle has emerged as an advanced power generation system owing to its better efficiency, compactness, and capability to synergize with a broad range of boundary conditions. Its superior performance is due to the liquid-like compression near the critical point. However, this phenomenon deteriorates significantly for elevated heat sink temperatures and is therefore highly detrimental to the cycle performance. Thus, this study proposed and investigated an integrated power and refrigeration cycle scheme to curtail the effects of elevated heat sink temperatures. A theoretical model of the proposed scheme based on industrial flue gases was developed, and the influence of heat sink at a range of heat-source temperatures (200–500 °C) was examined. Subsequently, benchmark cases are established and optimized, and the performance improvement with respect to the benchmark case is reported, with net power as the performance indicator. The optimization of the benchmark case reveals that the simultaneous optimization of low- and high-pressure levels of the cycle is necessary to maximize the net power. The parametric investigation of the proposed configuration shows that the performance is sensitive to the saturation temperature in the evaporator of the refrigeration cycle and to the ratio of low- and high-pressure levels in the power cycle. Therefore, the proposed case was optimized for both influencing parameters for each boundary condition. The results show that for a given heat-source temperature, higher heat sink temperatures favor the proposed design. For the heat-source temperatures of 200 °C, the benchmark case is superior for all heat sink conditions, whereas for 300 °C, 400 °C, and 500 °C, the proposed system results in an increase in power generation of 10.67%, 7.2%, and 5.2%, respectively, at a sink temperature of 50 °C. Finally, a case study with molten salt as the heat source was conducted, and the results indicated that the proposed scheme outperformed the benchmark case by 32.87% in terms of net power. The results are significant in simplifying the design of pressurization components and performance improvement of the supercritical carbon dioxide power cycle at elevated heat sink temperatures.

Suggested Citation

  • Muhammad, Hafiz Ali & Cho, Junhyun & Cho, Jongjae & Choi, Bongsu & Roh, Chulwoo & Ishfaq, Hafiz Ahmad & Lee, Gilbong & Shin, Hyungki & Baik, Young-Jin & Lee, Beomjoon, 2022. "Performance improvement of supercritical carbon dioxide power cycle at elevated heat sink temperatures," Energy, Elsevier, vol. 239(PD).
    • Handle: RePEc:eee:energy:v:239:y:2022:i:pd:s0360544221024646
    DOI: 10.1016/j.energy.2021.122216
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0360544221024646
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.energy.2021.122216?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Pan, Lisheng & Li, Bing & Shi, Weixiu & Wei, Xiaolin, 2019. "Optimization of the self-condensing CO2 transcritical power cycle using solar thermal energy," Applied Energy, Elsevier, vol. 253(C), pages 1-1.
    2. Baik, Young-Jin & Kim, Minsung & Chang, Ki Chang & Kim, Sung Jin, 2011. "Power-based performance comparison between carbon dioxide and R125 transcritical cycles for a low-grade heat source," Applied Energy, Elsevier, vol. 88(3), pages 892-898, March.
    3. Forman, Clemens & Muritala, Ibrahim Kolawole & Pardemann, Robert & Meyer, Bernd, 2016. "Estimating the global waste heat potential," Renewable and Sustainable Energy Reviews, Elsevier, vol. 57(C), pages 1568-1579.
    4. Thanganadar, Dhinesh & Asfand, Faisal & Patchigolla, Kumar, 2019. "Thermal performance and economic analysis of supercritical Carbon Dioxide cycles in combined cycle power plant," Applied Energy, Elsevier, vol. 255(C).
    5. Ahn, Yoonhan & Lee, Jekyoung & Kim, Seong Gu & Lee, Jeong Ik & Cha, Jae Eun & Lee, Si-Woo, 2015. "Design consideration of supercritical CO2 power cycle integral experiment loop," Energy, Elsevier, vol. 86(C), pages 115-127.
    6. Sarkar, Jahar, 2015. "Review and future trends of supercritical CO2 Rankine cycle for low-grade heat conversion," Renewable and Sustainable Energy Reviews, Elsevier, vol. 48(C), pages 434-451.
    7. Muhammad, Hafiz Ali & Lee, Beomjoon & Cho, Junhyun & Rehman, Zabdur & Choi, Bongsu & Cho, Jongjae & Roh, Chulwoo & Lee, Gilbong & Imran, Muhammad & Baik, Young-Jin, 2021. "Application of advanced exergy analysis for optimizing the design of carbon dioxide pressurization system," Energy, Elsevier, vol. 228(C).
    8. Song, Jian & Li, Xue-song & Ren, Xiao-dong & Gu, Chun-wei, 2018. "Performance analysis and parametric optimization of supercritical carbon dioxide (S-CO2) cycle with bottoming Organic Rankine Cycle (ORC)," Energy, Elsevier, vol. 143(C), pages 406-416.
    9. Correa, Faustino & Barraza, Rodrigo & Soo Too, Yen Chean & Vasquez Padilla, Ricardo & Cardemil, José M., 2021. "Optimized operation of recompression sCO2 Brayton cycle based on adjustable recompression fraction under variable conditions," Energy, Elsevier, vol. 227(C).
    10. Kim, Young Min & Sohn, Jeong Lak & Yoon, Eui Soo, 2017. "Supercritical CO2 Rankine cycles for waste heat recovery from gas turbine," Energy, Elsevier, vol. 118(C), pages 893-905.
    11. Wang, Xurong & Yang, Yi & Zheng, Ya & Dai, Yiping, 2017. "Exergy and exergoeconomic analyses of a supercritical CO2 cycle for a cogeneration application," Energy, Elsevier, vol. 119(C), pages 971-982.
    12. Crespi, Francesco & Gavagnin, Giacomo & Sánchez, David & Martínez, Gonzalo S., 2017. "Supercritical carbon dioxide cycles for power generation: A review," Applied Energy, Elsevier, vol. 195(C), pages 152-183.
    13. Liu, Yaping & Wang, Ying & Huang, Diangui, 2019. "Supercritical CO2 Brayton cycle: A state-of-the-art review," Energy, Elsevier, vol. 189(C).
    14. Tozlu, Alperen & Abuşoğlu, Ayşegül & Özahi, Emrah, 2018. "Thermoeconomic analysis and optimization of a Re-compression supercritical CO2 cycle using waste heat of Gaziantep Municipal Solid Waste Power Plant," Energy, Elsevier, vol. 143(C), pages 168-180.
    15. Uusitalo, Antti & Ameli, Alireza & Turunen-Saaresti, Teemu, 2019. "Thermodynamic and turbomachinery design analysis of supercritical Brayton cycles for exhaust gas heat recovery," Energy, Elsevier, vol. 167(C), pages 60-79.
    16. Mecheri, Mounir & Le Moullec, Yann, 2016. "Supercritical CO2 Brayton cycles for coal-fired power plants," Energy, Elsevier, vol. 103(C), pages 758-771.
    17. Muhammad, Hafiz Ali & Lee, Beomjoon & Lee, Gilbong & Cho, Junhyun & Baik, Young-Jin, 2019. "Investigation of leakage reinjection system for supercritical CO2 power cycle using heat pump," Renewable Energy, Elsevier, vol. 144(C), pages 97-106.
    18. Li, Chengyu & Wang, Huaixin, 2016. "Power cycles for waste heat recovery from medium to high temperature flue gas sources – from a view of thermodynamic optimization," Applied Energy, Elsevier, vol. 180(C), pages 707-721.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Dingchen Wu & Mingshan Wei & Ran Tian & Siyu Zheng & Jundi He, 2022. "A Review of Flow and Heat Transfer Characteristics of Supercritical Carbon Dioxide under Cooling Conditions in Energy and Power Systems," Energies, MDPI, vol. 15(23), pages 1-28, November.
    2. Jihoo Jung & Jehyun Lee & Sangjin Choi & Woonho Baek, 2022. "Information Analysis on Foreign Institution for International R&D Collaboration Using Natural Language Processing," Energies, MDPI, vol. 16(1), pages 1-17, December.
    3. Wang, Yiming & Xie, Gongnan & Zhu, Huaitao & Yuan, Han, 2023. "Assessment on energy and exergy of combined supercritical CO2 Brayton cycles with sizing printed-circuit-heat-exchangers," Energy, Elsevier, vol. 263(PA).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Kunniyoor, Vijayaraj & Singh, Punit & Nadella, Karthik, 2020. "Value of closed-cycle gas turbines with design assessment," Applied Energy, Elsevier, vol. 269(C).
    2. Penkuhn, Mathias & Tsatsaronis, George, 2020. "Systematic evaluation of efficiency improvement options for sCO2 Brayton cycles," Energy, Elsevier, vol. 210(C).
    3. Gao, Lei & Cao, Tao & Hwang, Yunho & Radermacher, Reinhard, 2022. "Robustness analysis in supercritical CO2 power generation system configuration optimization," Energy, Elsevier, vol. 242(C).
    4. Marchionni, Matteo & Bianchi, Giuseppe & Tassou, Savvas A., 2018. "Techno-economic assessment of Joule-Brayton cycle architectures for heat to power conversion from high-grade heat sources using CO2 in the supercritical state," Energy, Elsevier, vol. 148(C), pages 1140-1152.
    5. Yang, Yiping & Huang, Yulei & Jiang, Peixue & Zhu, Yinhai, 2020. "Multi-objective optimization of combined cooling, heating, and power systems with supercritical CO2 recompression Brayton cycle," Applied Energy, Elsevier, vol. 271(C).
    6. Linares, José Ignacio & Cantizano, Alexis & Arenas, Eva & Moratilla, Beatriz Yolanda & Martín-Palacios, Víctor & Batet, Lluis, 2017. "Recuperated versus single-recuperator re-compressed supercritical CO2 Brayton power cycles for DEMO fusion reactor based on dual coolant lithium lead blanket," Energy, Elsevier, vol. 140(P1), pages 307-317.
    7. Bonalumi, Davide & Giuffrida, Antonio & Sicali, Federico, 2022. "Techno-economic investigations of supercritical CO2-based partial heating cycle as bottoming system of a small gas turbine," Energy, Elsevier, vol. 252(C).
    8. Wang, Rui & Wang, Xuan & Bian, Xingyan & Zhang, Xuanang & Cai, Jinwen & Tian, Hua & Shu, Gequn & Wang, Mingtao, 2023. "An optimal split ratio in design and control of a recompression supercritical CO2 Brayton system," Energy, Elsevier, vol. 277(C).
    9. Kim, Sunjin & Kim, Min Soo & Kim, Minsung, 2020. "Parametric study and optimization of closed Brayton power cycle considering the charge amount of working fluid," Energy, Elsevier, vol. 198(C).
    10. Wang, Shengpeng & Zhang, Yifan & Li, Hongzhi & Yao, Mingyu & Peng, Botao & Yan, Junjie, 2020. "Thermohydrodynamic analysis of the vertical gas wall and reheat gas wall in a 300 MW supercritical CO2 boiler," Energy, Elsevier, vol. 211(C).
    11. Li, Ligeng & Tian, Hua & Liu, Peng & Shi, Lingfeng & Shu, Gequn, 2021. "Optimization of CO2 Transcritical Power Cycle (CTPC) for engine waste heat recovery based on split concept," Energy, Elsevier, vol. 229(C).
    12. Son, Seongmin & Lee, Jeong Ik, 2018. "Application of adjoint sensitivity analysis method to supercritical CO2 power cycle optimization," Energy, Elsevier, vol. 147(C), pages 1153-1164.
    13. Fallah, M. & Mohammadi, Z. & Mahmoudi, S.M. Seyed, 2022. "Advanced exergy analysis of the combined S–CO2/ORC system," Energy, Elsevier, vol. 241(C).
    14. Wang, Zhe & Jiang, Yuemao & Ma, Yue & Han, Fenghui & Ji, Yulong & Cai, Wenjian, 2022. "A partial heating supercritical CO2 nested transcritical CO2 cascade power cycle for marine engine waste heat recovery: Thermodynamic, economic, and footprint analysis," Energy, Elsevier, vol. 261(PA).
    15. Muhammed Saeed & Khaled Alawadi & Sung Chul Kim, 2020. "Performance of Supercritical CO 2 Power Cycle and Its Turbomachinery with the Printed Circuit Heat Exchanger with Straight and Zigzag Channels," Energies, MDPI, vol. 14(1), pages 1-25, December.
    16. Jeong, Yongju & Son, Seongmin & Cho, Seong Kuk & Baik, Seungjoon & Lee, Jeong Ik, 2020. "Evaluation of supercritical CO2 compressor off-design performance prediction methods," Energy, Elsevier, vol. 213(C).
    17. Sadeghi, Mohsen & Seyed Mahmoudi, Seyed Mohammad & Rosen, Marc A., 2022. "Thermoeconomic analysis of two solid oxide fuel cell based cogeneration plants integrated with simple or modified supercritical CO2 Brayton cycles: A comparative study," Energy, Elsevier, vol. 259(C).
    18. Cao, Yue & Rattner, Alexander S. & Dai, Yiping, 2018. "Thermoeconomic analysis of a gas turbine and cascaded CO2 combined cycle using thermal oil as an intermediate heat-transfer fluid," Energy, Elsevier, vol. 162(C), pages 1253-1268.
    19. Wang, Xurong & Dai, Yiping, 2016. "Exergoeconomic analysis of utilizing the transcritical CO2 cycle and the ORC for a recompression supercritical CO2 cycle waste heat recovery: A comparative study," Applied Energy, Elsevier, vol. 170(C), pages 193-207.
    20. Ehsan, M. Monjurul & Guan, Zhiqiang & Gurgenci, Hal & Klimenko, Alexander, 2020. "Feasibility of dry cooling in supercritical CO2 power cycle in concentrated solar power application: Review and a case study," Renewable and Sustainable Energy Reviews, Elsevier, vol. 132(C).

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:energy:v:239:y:2022:i:pd:s0360544221024646. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.journals.elsevier.com/energy .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.