IDEAS home Printed from https://ideas.repec.org/a/eee/appene/v333y2023ics0306261922018372.html
   My bibliography  Save this article

Demonstration system of pumped heat energy storage (PHES) and its round-trip efficiency

Author

Listed:
  • Ameen, Muhammad Tahir
  • Ma, Zhiwei
  • Smallbone, Andrew
  • Norman, Rose
  • Roskilly, Anthony Paul

Abstract

Among the known energy storage technologies aiming to increase the efficiency and stability of power grids, Pumped Heat Energy Storage (PHES) is considered by many as a promising candidate because of its flexibility, potential for scale-up and low cost per energy storage unit. Whilst there are numerous demonstration systems under development, as it stands the only PHES demonstration system to be realised at scale is located in Hampshire, UK. This paper aims to present the results and analysis obtained from its commissioning and testing as part of an on-going study. The system was designed to offer a nominal power size of 150 kWe and energy storage capacity of 600 kWhe for an 8-hour storage cycle. This work presents evidence of the system Round-trip efficiency (RTE), which is considered as a fundamental performance metric for large-scale energy storage technologies. Recorded Pressure-Volume (P-V) measurements from recent heat pump/engine testing at part-load offers useful insight in terms of overall performance. Models are also developed to simulate the system to finally predict the performance at full-load conditions. The system and principle of operation are described first, followed by mathematical modelling outlining heat transfer mechanism and associated key losses involved in thermodynamic processes within components, and finally results are presented and compared at different operating conditions using different working gases. The results show good agreement with earlier studies, which indicate that expected electricity-to-electricity RTE is quite comparable to other mature technologies such as Pumped Hydropower Storage and Compressed Air Energy Storage. The cyclic operation of the system is also discussed. One-off storage cycle results in lower RTEs compared to a load-levelling cyclic operation where the efficiency is significantly improved due to stable packed-bed behaviour and better utilisation after an initial transient state.

Suggested Citation

  • Ameen, Muhammad Tahir & Ma, Zhiwei & Smallbone, Andrew & Norman, Rose & Roskilly, Anthony Paul, 2023. "Demonstration system of pumped heat energy storage (PHES) and its round-trip efficiency," Applied Energy, Elsevier, vol. 333(C).
    • Handle: RePEc:eee:appene:v:333:y:2023:i:c:s0306261922018372
    DOI: 10.1016/j.apenergy.2022.120580
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0306261922018372
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.apenergy.2022.120580?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Benato, Alberto, 2017. "Performance and cost evaluation of an innovative Pumped Thermal Electricity Storage power system," Energy, Elsevier, vol. 138(C), pages 419-436.
    2. White, A.J., 2009. "Thermodynamic analysis of the reverse Joule-Brayton cycle heat pump for domestic heating," Applied Energy, Elsevier, vol. 86(11), pages 2443-2450, November.
    3. White, Alexander & McTigue, Joshua & Markides, Christos, 2014. "Wave propagation and thermodynamic losses in packed-bed thermal reservoirs for energy storage," Applied Energy, Elsevier, vol. 130(C), pages 648-657.
    4. Liang, Ting & Vecchi, Andrea & Knobloch, Kai & Sciacovelli, Adriano & Engelbrecht, Kurt & Li, Yongliang & Ding, Yulong, 2022. "Key components for Carnot Battery: Technology review, technical barriers and selection criteria," Renewable and Sustainable Energy Reviews, Elsevier, vol. 163(C).
    5. White, Alexander J., 2011. "Loss analysis of thermal reservoirs for electrical energy storage schemes," Applied Energy, Elsevier, vol. 88(11), pages 4150-4159.
    6. Zhao, Yongliang & Song, Jian & Liu, Ming & Zhao, Yao & Olympios, Andreas V. & Sapin, Paul & Yan, Junjie & Markides, Christos N., 2022. "Thermo-economic assessments of pumped-thermal electricity storage systems employing sensible heat storage materials," Renewable Energy, Elsevier, vol. 186(C), pages 431-456.
    7. Bazdar, Elaheh & Sameti, Mohammad & Nasiri, Fuzhan & Haghighat, Fariborz, 2022. "Compressed air energy storage in integrated energy systems: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 167(C).
    8. Olabi, A.G. & Onumaegbu, C. & Wilberforce, Tabbi & Ramadan, Mohamad & Abdelkareem, Mohammad Ali & Al – Alami, Abdul Hai, 2021. "Critical review of energy storage systems," Energy, Elsevier, vol. 214(C).
    9. Luo, Xing & Wang, Jihong & Dooner, Mark & Clarke, Jonathan, 2015. "Overview of current development in electrical energy storage technologies and the application potential in power system operation," Applied Energy, Elsevier, vol. 137(C), pages 511-536.
    10. Zhang, Han & Wang, Liang & Lin, Xipeng & Chen, Haisheng, 2022. "Technical and economic analysis of Brayton-cycle-based pumped thermal electricity storage systems with direct and indirect thermal energy storage," Energy, Elsevier, vol. 239(PC).
    11. Abdul Ghani Olabi & Tabbi Wilberforce & Mohammad Ali Abdelkareem & Mohamad Ramadan, 2021. "Critical Review of Flywheel Energy Storage System," Energies, MDPI, vol. 14(8), pages 1-33, April.
    12. Moss, R. W. & Roskilly, A. P. & Nanda, S. K., 2005. "Reciprocating Joule-cycle engine for domestic CHP systems," Applied Energy, Elsevier, vol. 80(2), pages 169-185, February.
    13. Steinmann, Wolf-Dieter & Bauer, Dan & Jockenhöfer, Henning & Johnson, Maike, 2019. "Pumped thermal energy storage (PTES) as smart sector-coupling technology for heat and electricity," Energy, Elsevier, vol. 183(C), pages 185-190.
    14. Albert, Max & Ma, Zhiwei & Bao, Huashan & Roskilly, Anthony Paul, 2022. "Operation and performance of Brayton Pumped Thermal Energy Storage with additional latent storage," Applied Energy, Elsevier, vol. 312(C).
    15. Steinmann, Wolf-Dieter, 2017. "Thermo-mechanical concepts for bulk energy storage," Renewable and Sustainable Energy Reviews, Elsevier, vol. 75(C), pages 205-219.
    16. Rutczyk, Bartlomiej & Szczygieł, Ireneusz, 2021. "Development of internal heat transfer correlations for the cylinders of reciprocating machines," Energy, Elsevier, vol. 230(C).
    17. Esence, Thibaut & Bruch, Arnaud & Fourmigué, Jean-François & Stutz, Benoit, 2019. "A versatile one-dimensional numerical model for packed-bed heat storage systems," Renewable Energy, Elsevier, vol. 133(C), pages 190-204.
    18. Guido Francesco Frate & Lorenzo Ferrari & Umberto Desideri, 2020. "Rankine Carnot Batteries with the Integration of Thermal Energy Sources: A Review," Energies, MDPI, vol. 13(18), pages 1-28, September.
    19. McTigue, Joshua D. & White, Alexander J. & Markides, Christos N., 2015. "Parametric studies and optimisation of pumped thermal electricity storage," Applied Energy, Elsevier, vol. 137(C), pages 800-811.
    20. Wang, Liang & Lin, Xipeng & Chai, Lei & Peng, Long & Yu, Dong & Chen, Haisheng, 2019. "Cyclic transient behavior of the Joule–Brayton based pumped heat electricity storage: Modeling and analysis," Renewable and Sustainable Energy Reviews, Elsevier, vol. 111(C), pages 523-534.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Yong, Qingqing & Jin, Kaiyuan & Li, Xiaobo & Yang, Ronggui, 2023. "Thermo-economic analysis for a novel grid-scale pumped thermal electricity storage system coupled with a coal-fired power plant," Energy, Elsevier, vol. 280(C).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Zhao, Yongliang & Song, Jian & Liu, Ming & Zhao, Yao & Olympios, Andreas V. & Sapin, Paul & Yan, Junjie & Markides, Christos N., 2022. "Thermo-economic assessments of pumped-thermal electricity storage systems employing sensible heat storage materials," Renewable Energy, Elsevier, vol. 186(C), pages 431-456.
    2. Liang, Ting & Vecchi, Andrea & Knobloch, Kai & Sciacovelli, Adriano & Engelbrecht, Kurt & Li, Yongliang & Ding, Yulong, 2022. "Key components for Carnot Battery: Technology review, technical barriers and selection criteria," Renewable and Sustainable Energy Reviews, Elsevier, vol. 163(C).
    3. Alberto Benato & Francesco De Vanna & Anna Stoppato, 2022. "Levelling the Photovoltaic Power Profile with the Integrated Energy Storage System," Energies, MDPI, vol. 15(24), pages 1-21, December.
    4. Frate, Guido Francesco & Ferrari, Lorenzo & Desideri, Umberto, 2021. "Energy storage for grid-scale applications: Technology review and economic feasibility analysis," Renewable Energy, Elsevier, vol. 163(C), pages 1754-1772.
    5. Zhang, Han & Wang, Liang & Lin, Xipeng & Chen, Haisheng, 2020. "Combined cooling, heating, and power generation performance of pumped thermal electricity storage system based on Brayton cycle," Applied Energy, Elsevier, vol. 278(C).
    6. Xue, X.J. & Zhao, C.Y., 2023. "Transient behavior and thermodynamic analysis of Brayton-like pumped-thermal electricity storage based on packed-bed latent heat/cold stores," Applied Energy, Elsevier, vol. 329(C).
    7. Zhang, Han & Wang, Liang & Lin, Xipeng & Chen, Haisheng, 2023. "Operating mode of Brayton-cycle-based pumped thermal electricity storage system: Constant compression ratio or constant rotational speed?," Applied Energy, Elsevier, vol. 343(C).
    8. Ge, Y.Q. & Zhao, Y. & Zhao, C.Y., 2021. "Transient simulation and thermodynamic analysis of pumped thermal electricity storage based on packed-bed latent heat/cold stores," Renewable Energy, Elsevier, vol. 174(C), pages 939-951.
    9. Blanquiceth, J. & Cardemil, J.M. & Henríquez, M. & Escobar, R., 2023. "Thermodynamic evaluation of a pumped thermal electricity storage system integrated with large-scale thermal power plants," Renewable and Sustainable Energy Reviews, Elsevier, vol. 175(C).
    10. Zhang, Han & Wang, Liang & Lin, Xipeng & Chen, Haisheng, 2022. "Technical and economic analysis of Brayton-cycle-based pumped thermal electricity storage systems with direct and indirect thermal energy storage," Energy, Elsevier, vol. 239(PC).
    11. Tassenoy, Robin & Couvreur, Kenny & Beyne, Wim & De Paepe, Michel & Lecompte, Steven, 2022. "Techno-economic assessment of Carnot batteries for load-shifting of solar PV production of an office building," Renewable Energy, Elsevier, vol. 199(C), pages 1133-1144.
    12. Georgiou, Solomos & Shah, Nilay & Markides, Christos N., 2018. "A thermo-economic analysis and comparison of pumped-thermal and liquid-air electricity storage systems," Applied Energy, Elsevier, vol. 226(C), pages 1119-1133.
    13. Zhang, Han & Wang, Liang & Lin, Xipeng & Chen, Haisheng, 2023. "Parametric optimisation and thermo-economic analysis of Joule–Brayton cycle-based pumped thermal electricity storage system under various charging–discharging periods," Energy, Elsevier, vol. 263(PE).
    14. Zhang, Yanchao & Xie, Zhenzhen, 2022. "Thermodynamic efficiency and bounds of pumped thermal electricity storage under whole process ecological optimization," Renewable Energy, Elsevier, vol. 188(C), pages 711-720.
    15. Saghafifar, Mohammad & Schnellmann, Matthias A. & Scott, Stuart A., 2020. "Chemical looping electricity storage," Applied Energy, Elsevier, vol. 279(C).
    16. Frate, Guido Francesco & Baccioli, Andrea & Bernardini, Leonardo & Ferrari, Lorenzo, 2022. "Assessment of the off-design performance of a solar thermally-integrated pumped-thermal energy storage," Renewable Energy, Elsevier, vol. 201(P1), pages 636-650.
    17. Guo, Juncheng & Cai, Ling & Chen, Jincan & Zhou, Yinghui, 2016. "Performance evaluation and parametric choice criteria of a Brayton pumped thermal electricity storage system," Energy, Elsevier, vol. 113(C), pages 693-701.
    18. McTigue, J.D. & White, A.J., 2018. "A comparison of radial-flow and axial-flow packed beds for thermal energy storage," Applied Energy, Elsevier, vol. 227(C), pages 533-541.
    19. Albert, Max & Ma, Zhiwei & Bao, Huashan & Roskilly, Anthony Paul, 2022. "Operation and performance of Brayton Pumped Thermal Energy Storage with additional latent storage," Applied Energy, Elsevier, vol. 312(C).
    20. Wang, Liang & Lin, Xipeng & Zhang, Han & Peng, Long & Ling, Haoshu & Zhang, Shuang & Chen, Haisheng, 2023. "Thermodynamic analysis and optimization of pumped thermal–liquid air energy storage (PTLAES)," Applied Energy, Elsevier, vol. 332(C).

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:appene:v:333:y:2023:i:c:s0306261922018372. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.elsevier.com/wps/find/journaldescription.cws_home/405891/description#description .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.