IDEAS home Printed from https://ideas.repec.org/a/eee/appene/v130y2014icp723-737.html
   My bibliography  Save this article

New concept of spray saturation tower for micro Humid Air Turbine applications

Author

Listed:
  • De Paepe, W.
  • Contino, F.
  • Delattin, F.
  • Bram, S.
  • De Ruyck, J.

Abstract

The micro Humid Air Turbine (mHAT) has proven to have the highest potential of all mixed air/water micro Gas Turbines (mGTs). Turning a mGT into a mHAT however requires the installation of a saturation tower. Most common saturation towers use packing material to increase the contact area between compressed air and water. The packing material however causes a pressure drop, which has a severe negative effect on the mGT performance. To limit this pressure drop, we have developed a spray tower without packing that uses nozzles to inject water in the compressed air. In this paper, we propose a design for the spray tower based on 2-phase flow simulations. The two major constraints during the design were minimal pressure loss and tower size. A sensitivity analysis was performed in order to indicate the key parameters to obtain fully saturated air from the tower. Results of simulations showed that using a spray tower reduces the pressure losses when compared to a classic saturation tower. Sensitivity analysis showed that droplet diameter and injected water mass flow rate have the largest effect on the final size of the spray tower. Finally, a cross-current spray tower design was proposed for a Turbec T100mGT because the sensitivity analysis showed that cross-current droplets injection meets the design constraints best.

Suggested Citation

  • De Paepe, W. & Contino, F. & Delattin, F. & Bram, S. & De Ruyck, J., 2014. "New concept of spray saturation tower for micro Humid Air Turbine applications," Applied Energy, Elsevier, vol. 130(C), pages 723-737.
  • Handle: RePEc:eee:appene:v:130:y:2014:i:c:p:723-737
    DOI: 10.1016/j.apenergy.2014.03.055
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0306261914002955
    Download Restriction: Full text for ScienceDirect subscribers only

    File URL: https://libkey.io/10.1016/j.apenergy.2014.03.055?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. De Paepe, Ward & Delattin, Frank & Bram, Svend & De Ruyck, Jacques, 2012. "Steam injection experiments in a microturbine – A thermodynamic performance analysis," Applied Energy, Elsevier, vol. 97(C), pages 569-576.
    2. De Paepe, Ward & Delattin, Frank & Bram, Svend & De Ruyck, Jacques, 2013. "Water injection in a micro gas turbine – Assessment of the performance using a black box method," Applied Energy, Elsevier, vol. 112(C), pages 1291-1302.
    3. Niksiar, Arezou & Rahimi, Amir, 2009. "Energy and exergy analysis for cocurrent gas spray cooling systems based on the results of mathematical modeling and simulation," Energy, Elsevier, vol. 34(1), pages 14-21.
    4. Jonsson, Maria & Yan, Jinyue, 2005. "Humidified gas turbines—a review of proposed and implemented cycles," Energy, Elsevier, vol. 30(7), pages 1013-1078.
    5. Traverso, A., 2010. "Humidification tower for humid air gas turbine cycles: Experimental analysis," Energy, Elsevier, vol. 35(2), pages 894-901.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Montero Carrero, Marina & De Paepe, Ward & Parente, Alessandro & Contino, Francesco, 2016. "T100 mGT converted into mHAT for domestic applications: Economic analysis based on hourly demand," Applied Energy, Elsevier, vol. 164(C), pages 1019-1027.
    2. Wang, Maojian & Liu, Guilian & Hui, Chi Wai, 2016. "Simultaneous optimization and integration of gas turbine and air separation unit in IGCC plant," Energy, Elsevier, vol. 116(P2), pages 1294-1301.
    3. Renzi, Massimiliano & Patuzzi, Francesco & Baratieri, Marco, 2017. "Syngas feed of micro gas turbines with steam injection: Effects on performance, combustion and pollutants formation," Applied Energy, Elsevier, vol. 206(C), pages 697-707.
    4. Zhu, Guangya & Chow, T.T. & Fong, K.F. & Lee, C.K., 2019. "Comparative study on humidified gas turbine cycles with different air saturator designs," Applied Energy, Elsevier, vol. 254(C).
    5. Sun, Yubiao & Guan, Zhiqiang & Gurgenci, Hal & Wang, Jianyong & Dong, Peixin & Hooman, Kamel, 2019. "Spray cooling system design and optimization for cooling performance enhancement of natural draft dry cooling tower in concentrated solar power plants," Energy, Elsevier, vol. 168(C), pages 273-284.
    6. Montero Carrero, Marina & De Paepe, Ward & Bram, Svend & Musin, Frédéric & Parente, Alessandro & Contino, Francesco, 2016. "Humidified micro gas turbines for domestic users: An economic and primary energy savings analysis," Energy, Elsevier, vol. 117(P2), pages 429-438.
    7. Xu, Zhen & Lu, Yuan & Wang, Bo & Zhao, Lifeng & Xiao, Yunhan, 2021. "Experimental study on the off-design performances of a micro humid air turbine cycle: Thermodynamics, emissions and heat exchange," Energy, Elsevier, vol. 219(C).
    8. Zhang, Qing & Wang, Yuzhang & Jiang, Jiangjun & Weng, Shilie & Cao, Xiuling, 2022. "Coupling effect of key parameters of heat recovery components on the HAT cycle performance," Energy, Elsevier, vol. 238(PC).
    9. Montero Carrero, Marina & De Paepe, Ward & Bram, Svend & Parente, Alessandro & Contino, Francesco, 2017. "Does humidification improve the micro Gas Turbine cycle? Thermodynamic assessment based on Sankey and Grassmann diagrams," Applied Energy, Elsevier, vol. 204(C), pages 1163-1171.
    10. De Paepe, Ward & Montero Carrero, Marina & Bram, Svend & Contino, Francesco & Parente, Alessandro, 2017. "Waste heat recovery optimization in micro gas turbine applications using advanced humidified gas turbine cycle concepts," Applied Energy, Elsevier, vol. 207(C), pages 218-229.
    11. Cui, Haijiao & Li, Nianping & Peng, Jinqing & Yin, Rongxin & Li, Jingming & Wu, Zhibin, 2018. "Investigation on the thermal performance of a novel spray tower with upward spraying and downward gas flow," Applied Energy, Elsevier, vol. 231(C), pages 12-21.
    12. Zhang, Qing & He, Ming & Wang, Yuzhang & Weng, Shilie, 2020. "Experimental analysis of the air humidification process for humid air turbine cycle using a two-phase measurement system," Applied Energy, Elsevier, vol. 279(C).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Montero Carrero, Marina & De Paepe, Ward & Bram, Svend & Parente, Alessandro & Contino, Francesco, 2017. "Does humidification improve the micro Gas Turbine cycle? Thermodynamic assessment based on Sankey and Grassmann diagrams," Applied Energy, Elsevier, vol. 204(C), pages 1163-1171.
    2. Chacartegui, R. & Blanco, M.J. & Muñoz de Escalona, J.M. & Sánchez, D. & Sánchez, T., 2013. "Performance assessment of Molten Carbonate Fuel Cell–Humid Air Turbine hybrid systems," Applied Energy, Elsevier, vol. 102(C), pages 687-699.
    3. De Paepe, Ward & Montero Carrero, Marina & Bram, Svend & Contino, Francesco & Parente, Alessandro, 2017. "Waste heat recovery optimization in micro gas turbine applications using advanced humidified gas turbine cycle concepts," Applied Energy, Elsevier, vol. 207(C), pages 218-229.
    4. Renzi, Massimiliano & Patuzzi, Francesco & Baratieri, Marco, 2017. "Syngas feed of micro gas turbines with steam injection: Effects on performance, combustion and pollutants formation," Applied Energy, Elsevier, vol. 206(C), pages 697-707.
    5. Anwar Hamdan Al Assaf & Abdulkarem Amhamed & Odi Fawwaz Alrebei, 2022. "State of the Art in Humidified Gas Turbine Configurations," Energies, MDPI, vol. 15(24), pages 1-32, December.
    6. Giorgetti, S. & Bricteux, L. & Parente, A. & Blondeau, J. & Contino, F. & De Paepe, W., 2017. "Carbon capture on micro gas turbine cycles: Assessment of the performance on dry and wet operations," Applied Energy, Elsevier, vol. 207(C), pages 243-253.
    7. Zhao, Rongchao & Li, Weihua & Zhuge, Weilin & Zhang, Yangjun & Yin, Yong, 2017. "Numerical study on steam injection in a turbocompound diesel engine for waste heat recovery," Applied Energy, Elsevier, vol. 185(P1), pages 506-518.
    8. Maria Elena Diego & Muhammad Akram & Jean‐Michel Bellas & Karen N. Finney & Mohamed Pourkashanian, 2017. "Making gas‐CCS a commercial reality: The challenges of scaling up," Greenhouse Gases: Science and Technology, Blackwell Publishing, vol. 7(5), pages 778-801, October.
    9. Montero Carrero, Marina & De Paepe, Ward & Parente, Alessandro & Contino, Francesco, 2016. "T100 mGT converted into mHAT for domestic applications: Economic analysis based on hourly demand," Applied Energy, Elsevier, vol. 164(C), pages 1019-1027.
    10. De Paepe, Ward & Delattin, Frank & Bram, Svend & De Ruyck, Jacques, 2013. "Water injection in a micro gas turbine – Assessment of the performance using a black box method," Applied Energy, Elsevier, vol. 112(C), pages 1291-1302.
    11. Kang, Do Won & Jang, Hyuck Jun & Kim, Tong Seop, 2014. "Using compressor discharge air bypass to enhance power generation of a steam-injected gas turbine for combined heat and power," Energy, Elsevier, vol. 76(C), pages 390-399.
    12. Xu, Zhen & Lu, Yuan & Wang, Bo & Zhao, Lifeng & Chen, Changnian & Xiao, Yunhan, 2019. "Experimental evaluation of 100 kW grade micro humid air turbine cycles converted from a microturbine," Energy, Elsevier, vol. 175(C), pages 687-693.
    13. Farzaneh-Gord, Mahmood & Deymi-Dashtebayaz, Mahdi, 2009. "A new approach for enhancing performance of a gas turbine (case study: Khangiran refinery)," Applied Energy, Elsevier, vol. 86(12), pages 2750-2759, December.
    14. Kardaś, Dariusz & Polesek-Karczewska, Sylwia & Turzyński, Tomasz & Wardach-Święcicka, Izabela & Hercel, Paulina & Szymborski, Jakub & Heda, Łukasz, 2023. "Thermal performance enhancement of a red-hot air furnace for a micro-scale externally fired gas turbine system," Energy, Elsevier, vol. 282(C).
    15. Rehman, A. & Phalke, Deepak R. & Pandey, Rajesh, 2011. "Alternative fuel for gas turbine: Esterified jatropha oil–diesel blend," Renewable Energy, Elsevier, vol. 36(10), pages 2635-2640.
    16. Mahmood, Muhammad H. & Sultan, Muhammad & Miyazaki, Takahiko & Koyama, Shigeru & Maisotsenko, Valeriy S., 2016. "Overview of the Maisotsenko cycle – A way towards dew point evaporative cooling," Renewable and Sustainable Energy Reviews, Elsevier, vol. 66(C), pages 537-555.
    17. S. Hamed Fatemi Alavi & Amirreza Javaherian & S. M. S. Mahmoudi & Saeed Soltani & Marc A. Rosen, 2023. "Coupling a Gas Turbine Bottoming Cycle Using CO 2 as the Working Fluid with a Gas Cycle: Exergy Analysis Considering Combustion Chamber Steam Injection," Clean Technol., MDPI, vol. 5(3), pages 1-25, September.
    18. Galanti, Leandro & Massardo, Aristide F., 2011. "Micro gas turbine thermodynamic and economic analysis up to 500kWe size," Applied Energy, Elsevier, vol. 88(12), pages 4795-4802.
    19. Chacartegui, R. & Sánchez, D. & Muñoz, J.M. & Sánchez, T., 2009. "Alternative ORC bottoming cycles FOR combined cycle power plants," Applied Energy, Elsevier, vol. 86(10), pages 2162-2170, October.
    20. Guerra, Omar J. & Reklaitis, Gintaras V., 2018. "Advances and challenges in water management within energy systems," Renewable and Sustainable Energy Reviews, Elsevier, vol. 82(P3), pages 4009-4019.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:appene:v:130:y:2014:i:c:p:723-737. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.elsevier.com/wps/find/journaldescription.cws_home/405891/description#description .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.