IDEAS home Printed from https://ideas.repec.org/a/gam/jsusta/v14y2022i17p11045-d906634.html
   My bibliography  Save this article

Sustainable Development Solutions for the Medical Waste Problem Using Thermal Plasmas

Author

Listed:
  • Ahmed Rida Galaly

    (Department of Engineering Science, Applied College, Umm Al-Qura University, Makkah 24382, Saudi Arabia
    Department of Physics, Faculty of Science, Beni-Suef University, Beni Suef 62521, Egypt)

Abstract

Waste-to-energy (WTE) conversion is a vital process in the Middle East, especially in the Kingdom of Saudi Arabia (KSA), which is considered sustainable development for the environmental strategic project. Previous publications dealt with the environmentally friendly plasma treatment of wastes such as municipal waste, scrap tire waste, plastic waste, and grey water, using thermal plasmas produced by the cornerstone part of plasma reactors, namely the air plasma torch. In the present paper, with a view to energy recovery from medical waste, the thermodynamic properties of air plasma torches with a flow rate of air ranging from 10 mg/s to 30 mg/s and plasma jet temperatures ranging from 1500 °C to 5000 °C were investigated; these include power loss, enthalpy, plasma flux, and torch efficiency variation with plasma input power and air flow rate. The measured electrothermal efficiency of the plasma torch is in the range of 42% to 80% and increases with the increasing input power and gas flow rate. In Makkah, the number of beds in the hospitals is 10,500; the average annual weight of the medical waste in the hospitals is 2835 × 10 3 t, with an extracted amount of pyrolysis oil equivalent to 2268 × 10 3 t and an equivalent energy of 90 × 10 9 M J. In the proposed plasma treatment project, the amount of diesel oil after the distillation process will reach up to 1928 × 10 3 t, with an estimated sale profit of the electricity reaching up to 21 × 10 6 MW·h. The sale profit of pyrolysis oil in 2022 reaches up to USD 34.44 million, and the sale profit of electricity extracted by using the diesel oil in 2022 reaches up to USD 1020 million for households and USD 1445 million for factories.

Suggested Citation

  • Ahmed Rida Galaly, 2022. "Sustainable Development Solutions for the Medical Waste Problem Using Thermal Plasmas," Sustainability, MDPI, vol. 14(17), pages 1-12, September.
    • Handle: RePEc:gam:jsusta:v:14:y:2022:i:17:p:11045-:d:906634
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/2071-1050/14/17/11045/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/2071-1050/14/17/11045/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Lopez, Gartzen & Artetxe, Maite & Amutio, Maider & Bilbao, Javier & Olazar, Martin, 2017. "Thermochemical routes for the valorization of waste polyolefinic plastics to produce fuels and chemicals. A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 73(C), pages 346-368.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Ping Fa Chiang & Shanshan Han & Mugabekazi Joie Claire & Ndungutse Jean Maurice & Mohammadtaghi Vakili & Abdulmoseen Segun Giwa, 2024. "Sustainable Treatment of Spent Photovoltaic Solar Panels Using Plasma Pyrolysis Technology and Its Economic Significance," Clean Technol., MDPI, vol. 6(2), pages 1-21, April.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Huang, Jijiang & Veksha, Andrei & Chan, Wei Ping & Giannis, Apostolos & Lisak, Grzegorz, 2022. "Chemical recycling of plastic waste for sustainable material management: A prospective review on catalysts and processes," Renewable and Sustainable Energy Reviews, Elsevier, vol. 154(C).
    2. Chhabra, Vibhuti & Bambery, Keith & Bhattacharya, Sankar & Shastri, Yogendra, 2020. "Thermal and in situ infrared analysis to characterise the slow pyrolysis of mixed municipal solid waste (MSW) and its components," Renewable Energy, Elsevier, vol. 148(C), pages 388-401.
    3. Ye, Lian & Zhang, Jianliang & Wang, Guangwei & Wang, Chen & Mao, Xiaoming & Ning, Xiaojun & Zhang, Nan & Teng, Haipeng & Li, Jinhua & Wang, Chuan, 2023. "Feasibility analysis of plastic and biomass hydrochar for blast furnace injection," Energy, Elsevier, vol. 263(PD).
    4. Danfeng Zhang & Xin Wang & Liang Zhao & Huaqing Xie & Chen Guo & Feizhou Qian & Hui Dong & Yun Hu, 2023. "Numerical Investigation on Heat Transfer and Flow Resistance Characteristics of Superheater in Hydrocracking Heat Recovery Steam Generator," Energies, MDPI, vol. 16(17), pages 1-15, August.
    5. Anna Matuszewska & Adam Hańderek & Maciej Paczuski & Krzysztof Biernat, 2021. "Hydrocarbon Fractions from Thermolysis of Waste Plastics as Components of Engine Fuels," Energies, MDPI, vol. 14(21), pages 1-14, November.
    6. Wan Mahari, Wan Adibah & Chong, Cheng Tung & Cheng, Chin Kui & Lee, Chern Leing & Hendrata, Kristian & Yuh Yek, Peter Nai & Ma, Nyuk Ling & Lam, Su Shiung, 2018. "Production of value-added liquid fuel via microwave co-pyrolysis of used frying oil and plastic waste," Energy, Elsevier, vol. 162(C), pages 309-317.
    7. Huo, Erguang & Duan, Dengle & Lei, Hanwu & Liu, Chao & Zhang, Yayun & Wu, Jie & Zhao, Yunfeng & Huang, Zhiyang & Qian, Moriko & Zhang, Qingfa & Lin, Xiaona & Wang, Chenxi & Mateo, Wendy & Villota, Elm, 2020. "Phenols production form Douglas fir catalytic pyrolysis with MgO and biomass-derived activated carbon catalysts," Energy, Elsevier, vol. 199(C).
    8. Masnadi, Mohammad S. & Perrier, Patrick R. & Wang, Jingfan & Rutherford, Jeff & Brandt, Adam R., 2020. "Statistical proxy modeling for life cycle assessment and energetic analysis," Energy, Elsevier, vol. 194(C).
    9. Lucía Quesada & Mónica Calero de Hoces & M. A. Martín-Lara & Germán Luzón & G. Blázquez, 2020. "Performance of Different Catalysts for the In Situ Cracking of the Oil-Waxes Obtained by the Pyrolysis of Polyethylene Film Waste," Sustainability, MDPI, vol. 12(13), pages 1-15, July.
    10. Park, Ki-Bum & Jeong, Yong-Seong & Kim, Joo-Sik, 2019. "Activator-assisted pyrolysis of polypropylene," Applied Energy, Elsevier, vol. 253(C), pages 1-1.
    11. Zhao, Xiang & Klemeš, Jiří Jaromír & Fengqi You,, 2022. "Energy and environmental sustainability of waste personal protective equipment (PPE) treatment under COVID-19," Renewable and Sustainable Energy Reviews, Elsevier, vol. 153(C).
    12. Duan, Dengle & Feng, Zhiqiang & Dong, Xiaoyong & Chen, Xiaoru & Zhang, Yayun & Wan, Kun & Wang, Yunpu & Wang, Qin & Xiao, Gengsheng & Liu, Huifan & Ruan, Roger, 2021. "Improving bio-oil quality from low-density polyethylene pyrolysis: Effects of varying activation and pyrolysis parameters," Energy, Elsevier, vol. 232(C).
    13. Hannah Jones & Florence Saffar & Vasileios Koutsos & Dipa Ray, 2021. "Polyolefins and Polyethylene Terephthalate Package Wastes: Recycling and Use in Composites," Energies, MDPI, vol. 14(21), pages 1-43, November.
    14. Zhang, Yayun & Duan, Dengle & Lei, Hanwu & Villota, Elmar & Ruan, Roger, 2019. "Jet fuel production from waste plastics via catalytic pyrolysis with activated carbons," Applied Energy, Elsevier, vol. 251(C), pages 1-1.
    15. Bergman-Fonte, Clarissa & Nascimento da Silva, Gabriela & Império, Mariana & Draeger, Rebecca & Coutinho, Letícia & Cunha, Bruno S.L. & Rochedo, Pedro R.R. & Szklo, Alexandre & Schaeffer, Roberto, 2023. "Repurposing, co-processing and greenhouse gas mitigation – The Brazilian refining sector under deep decarbonization scenarios: A case study using integrated assessment modeling," Energy, Elsevier, vol. 282(C).
    16. Natacha Phetyim & Sommai Pivsa-Art, 2018. "Prototype Co-Pyrolysis of Used Lubricant Oil and Mixed Plastic Waste to Produce a Diesel-Like Fuel," Energies, MDPI, vol. 11(11), pages 1-11, November.
    17. Fazil, A. & Kumar, Sandeep & Mahajani, Sanjay M., 2022. "Downdraft co-gasification of high ash biomass and plastics," Energy, Elsevier, vol. 243(C).
    18. Park, Ki-Bum & Jeong, Yong-Seong & Guzelciftci, Begum & Kim, Joo-Sik, 2020. "Two-stage pyrolysis of polystyrene: Pyrolysis oil as a source of fuels or benzene, toluene, ethylbenzene, and xylenes," Applied Energy, Elsevier, vol. 259(C).
    19. Arabiourrutia, Miriam & Lopez, Gartzen & Artetxe, Maite & Alvarez, Jon & Bilbao, Javier & Olazar, Martin, 2020. "Waste tyre valorization by catalytic pyrolysis – A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 129(C).
    20. Kumar, Akash & Yan, Beibei & Tao, Junyu & Li, Jian & Kumari, Lata & Oba, Belay Tafa & Aborisade, Moses Akintayo & Chen, Guanyi, 2022. "Influence of waste plastic on pyrolysis of low-lipid microalgae: A study on thermokinetics, behaviors, evolved gas characteristics, and products distribution," Renewable Energy, Elsevier, vol. 185(C), pages 416-430.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jsusta:v:14:y:2022:i:17:p:11045-:d:906634. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.