IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v15y2022i18p6835-d918615.html
   My bibliography  Save this article

Comparison of the Combustion Process Parameters in a Diesel Engine Powered by Second-Generation Biodiesel Compared to the First-Generation Biodiesel

Author

Listed:
  • Piotr Łagowski

    (Department of Automotive Vehicles and Transportation, Faculty of Mechatronics and Mechanical Engineering, Kielce University of Technology, 25-314 Kielce, Poland)

  • Grzegorz Wcisło

    (Department of Bioprocess Engineering, Energy and Automation, Faculty of Production Engineering and Power Technologies, University of Agriculture in Krakow, 31-120 Kraków, Poland)

  • Dariusz Kurczyński

    (Department of Automotive Vehicles and Transportation, Faculty of Mechatronics and Mechanical Engineering, Kielce University of Technology, 25-314 Kielce, Poland)

Abstract

The use of biofuels to power compression–ignition engines makes it possible to reduce emissions of certain harmful components of exhaust gases. The purpose of this study was to determine the influence of second-generation biofuels on the course of indicator graphs and heat release characteristics of the Perkins 1104D-44TA compression–ignition engine. For comparative purposes, the same tests were carried out by feeding the engine with first-generation biofuel and diesel fuel. Babassu butyl esters (BBuE) were used as the second-generation biofuel. The second fuel was a first-generation biofuel—rapeseed oil methyl esters (RME). Analysis of the results made it possible to draw conclusions about the effect of using 2nd and 1st generation biofuels on the parameters of the combustion process. When the DF engine was powered, the lowest fuel dose per work cycle was obtained. In the case of RME and BBuE fuels, it depends on the engine load. For low loads, higher consumption is for RME, and for higher loads, fuel consumption for BBuE in-creases most often. This is due to the lower calorific value of the esters. The results of these tests indicate that feeding the engine with BBuE and RME fuel in most loads resulted in higher maximum combustion pressures compared to feeding the engine with DF which may be directly related to the higher cetane number of these fuels compared to DF and the oxygen content of these fuels. Feeding the engine with BBuE and RME esters compared to DF did not result in large differences in the maximum heat release rates HRmax. However, the values of the first and second maximum heat release rates x 1max and x 2max , in addition to the type of fuel, are strongly influenced by the operating conditions, especially the engine load. Analyzing the combustion angles of 5, 10, 50, and 90% of the fuel dose, it can be seen that feeding the engine with BBuE and RME esters for most measurement points results in faster combustion of the fuel dose compared to DF.

Suggested Citation

  • Piotr Łagowski & Grzegorz Wcisło & Dariusz Kurczyński, 2022. "Comparison of the Combustion Process Parameters in a Diesel Engine Powered by Second-Generation Biodiesel Compared to the First-Generation Biodiesel," Energies, MDPI, vol. 15(18), pages 1-21, September.
    • Handle: RePEc:gam:jeners:v:15:y:2022:i:18:p:6835-:d:918615
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/15/18/6835/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/15/18/6835/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Gintaras Valeika & Jonas Matijošius & Krzysztof Górski & Alfredas Rimkus & Ruslans Smigins, 2021. "A Study of Energy and Environmental Parameters of a Diesel Engine Running on Hydrogenated Vegetable Oil (HVO) with Addition of Biobutanol and Castor Oil," Energies, MDPI, vol. 14(13), pages 1-29, July.
    2. Labeckas, Gvidonas & Slavinskas, Stasys, 2006. "Performance of direct-injection off-road diesel engine on rapeseed oil," Renewable Energy, Elsevier, vol. 31(6), pages 849-863.
    3. Marta Ramos & Ana Paula Soares Dias & Jaime Filipe Puna & João Gomes & João Carlos Bordado, 2019. "Biodiesel Production Processes and Sustainable Raw Materials," Energies, MDPI, vol. 12(23), pages 1-30, November.
    4. Dariusz Kurczyński & Grzegorz Wcisło & Piotr Łagowski, 2021. "Experimental Study of Fuel Consumption and Exhaust Gas Composition of a Diesel Engine Powered by Biodiesel from Waste of Animal Origin," Energies, MDPI, vol. 14(12), pages 1-22, June.
    5. Aldhaidhawi, Mohanad & Chiriac, Radu & Badescu, Viorel, 2017. "Ignition delay, combustion and emission characteristics of Diesel engine fueled with rapeseed biodiesel – A literature review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 73(C), pages 178-186.
    6. Rafał Longwic & Przemysław Sander & Bronisław Jańczuk & Anna Zdziennicka & Katarzyna Szymczyk, 2021. "Modification of Canola Oil Physicochemical Properties by Hexane and Ethanol with Regards of Its Application in Diesel Engine," Energies, MDPI, vol. 14(15), pages 1-14, July.
    7. Çelikten, İsmet & Mutlu, Emre & Solmaz, Hamit, 2012. "Variation of performance and emission characteristics of a diesel engine fueled with diesel, rapeseed oil and hazelnut oil methyl ester blends," Renewable Energy, Elsevier, vol. 48(C), pages 122-126.
    8. Ramadhas, A.S. & Muraleedharan, C. & Jayaraj, S., 2005. "Performance and emission evaluation of a diesel engine fueled with methyl esters of rubber seed oil," Renewable Energy, Elsevier, vol. 30(12), pages 1789-1800.
    9. Wang, Meng & Nie, Kaili & Yun, Feng & Cao, Hao & Deng, Li & Wang, Fang & Tan, Tianwei, 2015. "Biodiesel with low temperature properties: Enzymatic synthesis of fusel alcohol fatty acid ester in a solvent free system," Renewable Energy, Elsevier, vol. 83(C), pages 1020-1025.
    10. Teixeira, Marcos Alexandre & da Graça Carvalho, Maria, 2007. "Regulatory mechanism for biomass renewable energy in Brazil, a case study of the Brazilian Babassu oil extraction industry," Energy, Elsevier, vol. 32(6), pages 999-1005.
    11. Flavio Caresana & Marco Bietresato & Massimiliano Renzi, 2021. "Injection and Combustion Analysis of Pure Rapeseed Oil Methyl Ester (RME) in a Pump-Line-Nozzle Fuel Injection System," Energies, MDPI, vol. 14(22), pages 1-25, November.
    12. Piotr Orliński & Piotr Laskowski & Magdalena Zimakowska-Laskowska & Paweł Mazuruk, 2022. "Assessment of the Impact of the Addition of Biomethanol to Diesel Fuel on the Coking Process of Diesel Engine Injectors," Energies, MDPI, vol. 15(3), pages 1-14, January.
    13. Guido, Chiara & Beatrice, Carlo & Napolitano, Pierpaolo, 2013. "Application of bioethanol/RME/diesel blend in a Euro5 automotive diesel engine: Potentiality of closed loop combustion control technology," Applied Energy, Elsevier, vol. 102(C), pages 13-23.
    14. Saladini, Fabrizio & Patrizi, Nicoletta & Pulselli, Federico M. & Marchettini, Nadia & Bastianoni, Simone, 2016. "Guidelines for emergy evaluation of first, second and third generation biofuels," Renewable and Sustainable Energy Reviews, Elsevier, vol. 66(C), pages 221-227.
    15. Jerzy Cisek & Szymon Lesniak & Winicjusz Stanik & Włodzimierz Przybylski, 2021. "The Synergy of Two Biofuel Additives on Combustion Process to Simultaneously Reduce NOx and PM Emissions," Energies, MDPI, vol. 14(10), pages 1-31, May.
    16. Mani, M. & Nagarajan, G. & Sampath, S., 2011. "Characterisation and effect of using waste plastic oil and diesel fuel blends in compression ignition engine," Energy, Elsevier, vol. 36(1), pages 212-219.
    17. Labecki, L. & Cairns, A. & Xia, J. & Megaritis, A. & Zhao, H. & Ganippa, L.C., 2012. "Combustion and emission of rapeseed oil blends in diesel engine," Applied Energy, Elsevier, vol. 95(C), pages 139-146.
    18. Bhuiya, M.M.K. & Rasul, M.G. & Khan, M.M.K. & Ashwath, N. & Azad, A.K., 2016. "Prospects of 2nd generation biodiesel as a sustainable fuel—Part: 1 selection of feedstocks, oil extraction techniques and conversion technologies," Renewable and Sustainable Energy Reviews, Elsevier, vol. 55(C), pages 1109-1128.
    19. Rafael Estevez & Laura Aguado-Deblas & Francisco J. López-Tenllado & Carlos Luna & Juan Calero & Antonio A. Romero & Felipa M. Bautista & Diego Luna, 2022. "Biodiesel Is Dead: Long Life to Advanced Biofuels—A Comprehensive Critical Review," Energies, MDPI, vol. 15(9), pages 1-39, April.
    20. Puhan, Sukumar & Jegan, R. & Balasubbramanian, K. & Nagarajan, G., 2009. "Effect of injection pressure on performance, emission and combustion characteristics of high linolenic linseed oil methyl ester in a DI diesel engine," Renewable Energy, Elsevier, vol. 34(5), pages 1227-1233.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Sujeet Kesharvani & Gaurav Dwivedi & Tikendra Nath Verma & Puneet Verma, 2022. "The Experimental Investigation of a Diesel Engine Using Ternary Blends of Algae Biodiesel, Ethanol and Diesel Fuels," Energies, MDPI, vol. 16(1), pages 1-18, December.
    2. Fatma Zohra Aklouche & Loubna Hadhoum & Khaled Loubar & Mohand Tazerout, 2023. "A Comprehensive Study on Effect of Biofuel Blending Obtained from Hydrothermal Liquefaction of Olive Mill Waste Water in Internal Combustion Engine," Energies, MDPI, vol. 16(6), pages 1-16, March.
    3. Zdzisław Chłopek & Hubert Sar & Krystian Szczepański & Dagna Zakrzewska, 2023. "Operational Issues of Using Replacement Fuels to Power Internal Combustion Engines," Energies, MDPI, vol. 16(6), pages 1-17, March.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Dariusz Kurczyński & Grzegorz Wcisło & Piotr Łagowski, 2021. "Experimental Study of Fuel Consumption and Exhaust Gas Composition of a Diesel Engine Powered by Biodiesel from Waste of Animal Origin," Energies, MDPI, vol. 14(12), pages 1-22, June.
    2. Aldhaidhawi, Mohanad & Chiriac, Radu & Badescu, Viorel, 2017. "Ignition delay, combustion and emission characteristics of Diesel engine fueled with rapeseed biodiesel – A literature review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 73(C), pages 178-186.
    3. Flavio Caresana & Marco Bietresato & Massimiliano Renzi, 2021. "Injection and Combustion Analysis of Pure Rapeseed Oil Methyl Ester (RME) in a Pump-Line-Nozzle Fuel Injection System," Energies, MDPI, vol. 14(22), pages 1-25, November.
    4. Tamilselvan, P. & Nallusamy, N. & Rajkumar, S., 2017. "A comprehensive review on performance, combustion and emission characteristics of biodiesel fuelled diesel engines," Renewable and Sustainable Energy Reviews, Elsevier, vol. 79(C), pages 1134-1159.
    5. Subramaniam, D. & Murugesan, A. & Avinash, A. & Kumaravel, A., 2013. "Bio-diesel production and its engine characteristics—An expatiate view," Renewable and Sustainable Energy Reviews, Elsevier, vol. 22(C), pages 361-370.
    6. Dariusz Kurczyński & Grzegorz Wcisło & Agnieszka Leśniak & Miłosław Kozak & Piotr Łagowski, 2022. "Production and Testing of Butyl and Methyl Esters as New Generation Biodiesels from Fatty Wastes of the Leather Industry," Energies, MDPI, vol. 15(22), pages 1-20, November.
    7. Kumar, Niraj & Varun, & Chauhan, Sant Ram, 2013. "Performance and emission characteristics of biodiesel from different origins: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 21(C), pages 633-658.
    8. Goh, Brandon Han Hoe & Ong, Hwai Chyuan & Cheah, Mei Yee & Chen, Wei-Hsin & Yu, Kai Ling & Mahlia, Teuku Meurah Indra, 2019. "Sustainability of direct biodiesel synthesis from microalgae biomass: A critical review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 107(C), pages 59-74.
    9. Mofijur, M. & Atabani, A.E. & Masjuki, H.H. & Kalam, M.A. & Masum, B.M., 2013. "A study on the effects of promising edible and non-edible biodiesel feedstocks on engine performance and emissions production: A comparative evaluation," Renewable and Sustainable Energy Reviews, Elsevier, vol. 23(C), pages 391-404.
    10. Azad, A.K. & Rasul, M.G. & Khan, M.M.K. & Sharma, Subhash C. & Mofijur, M. & Bhuiya, M.M.K., 2016. "Prospects, feedstocks and challenges of biodiesel production from beauty leaf oil and castor oil: A nonedible oil sources in Australia," Renewable and Sustainable Energy Reviews, Elsevier, vol. 61(C), pages 302-318.
    11. E, Jiaqiang & Pham, Minhhieu & Zhao, D. & Deng, Yuanwang & Le, DucHieu & Zuo, Wei & Zhu, Hao & Liu, Teng & Peng, Qingguo & Zhang, Zhiqing, 2017. "Effect of different technologies on combustion and emissions of the diesel engine fueled with biodiesel: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 80(C), pages 620-647.
    12. Sanjid, A. & Masjuki, H.H. & Kalam, M.A. & Rahman, S.M. Ashrafur & Abedin, M.J. & Palash, S.M., 2013. "Impact of palm, mustard, waste cooking oil and Calophyllum inophyllum biofuels on performance and emission of CI engine," Renewable and Sustainable Energy Reviews, Elsevier, vol. 27(C), pages 664-682.
    13. Ibrahim M. Hezam & Naga Rama Devi Vedala & Bathina Rajesh Kumar & Arunodaya Raj Mishra & Fausto Cavallaro, 2023. "Assessment of Biofuel Industry Sustainability Factors Based on the Intuitionistic Fuzzy Symmetry Point of Criterion and Rank-Sum-Based MAIRCA Method," Sustainability, MDPI, vol. 15(8), pages 1-24, April.
    14. Chalita Kaewbuddee & Ekarong Sukjit & Jiraphon Srisertpol & Somkiat Maithomklang & Khatha Wathakit & Niti Klinkaew & Pansa Liplap & Weerachai Arjharn, 2020. "Evaluation of Waste Plastic Oil-Biodiesel Blends as Alternative Fuels for Diesel Engines," Energies, MDPI, vol. 13(11), pages 1-16, June.
    15. Varun, & Singh, Paramvir & Tiwari, Samaresh Kumar & Singh, Rituparn & Kumar, Naresh, 2017. "Modification in combustion chamber geometry of CI engines for suitability of biodiesel: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 79(C), pages 1016-1033.
    16. Homeyra Piri & Massimiliano Renzi & Marco Bietresato, 2023. "Technical Implications of the Use of Biofuels in Agricultural and Industrial Compression-Ignition Engines with a Special Focus on the Interactions with (Bio)lubricants," Energies, MDPI, vol. 17(1), pages 1-45, December.
    17. Shah, Pinkesh R. & Gaitonde, U.N. & Ganesh, Anuradda, 2018. "Influence of soy-lecithin as bio-additive with straight vegetable oil on CI engine characteristics," Renewable Energy, Elsevier, vol. 115(C), pages 685-696.
    18. Khandal, S.V. & Banapurmath, N.R. & Gaitonde, V.N. & Hiremath, S.S., 2017. "Paradigm shift from mechanical direct injection diesel engines to advanced injection strategies of diesel homogeneous charge compression ignition (HCCI) engines- A comprehensive review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 70(C), pages 369-384.
    19. Habibullah, M. & Masjuki, H.H. & Kalam, M.A. & Rahman, S.M. Ashrafur & Mofijur, M. & Mobarak, H.M. & Ashraful, A.M., 2015. "Potential of biodiesel as a renewable energy source in Bangladesh," Renewable and Sustainable Energy Reviews, Elsevier, vol. 50(C), pages 819-834.
    20. Kumar, Shiva & Dinesha, P. & Rosen, Marc A., 2019. "Effect of injection pressure on the combustion, performance and emission characteristics of a biodiesel engine with cerium oxide nanoparticle additive," Energy, Elsevier, vol. 185(C), pages 1163-1173.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:15:y:2022:i:18:p:6835-:d:918615. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.