IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v14y2021i17p5545-d629434.html
   My bibliography  Save this article

Multi-Objective Constructal Optimization for Marine Condensers

Author

Listed:
  • Huijun Feng

    (Institute of Thermal Science and Power Engineering, Wuhan Institute of Technology, Wuhan 430205, China
    Hubei Provincial Engineering Technology Research Center of Green Chemical Equipment, Wuhan 430205, China
    School of Mechanical & Electrical Engineering, Wuhan Institute of Technology, Wuhan 430205, China)

  • Wei Tang

    (College of Power Engineering, Naval University of Engineering, Wuhan 430033, China)

  • Lingen Chen

    (Institute of Thermal Science and Power Engineering, Wuhan Institute of Technology, Wuhan 430205, China
    Hubei Provincial Engineering Technology Research Center of Green Chemical Equipment, Wuhan 430205, China
    School of Mechanical & Electrical Engineering, Wuhan Institute of Technology, Wuhan 430205, China)

  • Junchao Shi

    (College of Power Engineering, Naval University of Engineering, Wuhan 430033, China)

  • Zhixiang Wu

    (College of Power Engineering, Naval University of Engineering, Wuhan 430033, China)

Abstract

A marine condenser with exhausted steam as the working fluid is researched in this paper. Constructal designs of the condenser are numerically conducted based on single and multi-objective optimizations, respectively. In the single objective optimization, there is an optimal dimensionless tube diameter leading to the minimum total pumping power required by the condenser. After constructal optimization, the total pumping power is decreased by 42.3%. In addition, with the increase in mass flow rate of the steam and heat transfer area and the decrease in total heat transfer rate, the minimum total pumping power required by the condenser decreases. In the multi-objective optimization, the Pareto optimal set of the entropy generation rate and total pumping power is gained. The optimal results gained by three decision methods in the Pareto optimal set and single objective optimizations are compared by the deviation index. The optimal construct gained by the TOPSIS decision method corresponding to the smallest deviation index is recommended in the optimal design of the condenser. These research ideas can also be used to design other heat transfer devices.

Suggested Citation

  • Huijun Feng & Wei Tang & Lingen Chen & Junchao Shi & Zhixiang Wu, 2021. "Multi-Objective Constructal Optimization for Marine Condensers," Energies, MDPI, vol. 14(17), pages 1-18, September.
    • Handle: RePEc:gam:jeners:v:14:y:2021:i:17:p:5545-:d:629434
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/14/17/5545/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/14/17/5545/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Tang, Wei & Feng, Huijun & Chen, Lingen & Xie, Zhuojun & Shi, Junchao, 2021. "Constructal design for a boiler economizer," Energy, Elsevier, vol. 223(C).
    2. Yang, Jingye & Gao, Lei & Ye, Zhenhong & Hwang, Yunho & Chen, Jiangping, 2021. "Binary-objective optimization of latest low-GWP alternatives to R245fa for organic Rankine cycle application," Energy, Elsevier, vol. 217(C).
    3. Wu, Zhixiang & Feng, Huijun & Chen, Lingen & Xie, Zhuojun & Cai, Cunguang, 2019. "Pumping power minimization of an evaporator in ocean thermal energy conversion system based on constructal theory," Energy, Elsevier, vol. 181(C), pages 974-984.
    4. Azad, Abazar Vahdat & Amidpour, Majid, 2011. "Economic optimization of shell and tube heat exchanger based on constructal theory," Energy, Elsevier, vol. 36(2), pages 1087-1096.
    5. Lee, Ungki & Park, Sudong & Lee, Ikjin, 2020. "Robust design optimization (RDO) of thermoelectric generator system using non-dominated sorting genetic algorithm II (NSGA-II)," Energy, Elsevier, vol. 196(C).
    6. Kepes Rodrigues, Michel & da Silva Brum, Ruth & Vaz, Joaquim & Oliveira Rocha, Luiz Alberto & Domingues dos Santos, Elizaldo & Isoldi, Liércio André, 2015. "Numerical investigation about the improvement of the thermal potential of an Earth-Air Heat Exchanger (EAHE) employing the Constructal Design method," Renewable Energy, Elsevier, vol. 80(C), pages 538-551.
    7. Marcin Jankowski & Aleksandra Borsukiewicz & Kamel Hooman, 2020. "Development of Decision-Making Tool and Pareto Set Analysis for Bi-Objective Optimization of an ORC Power Plant," Energies, MDPI, vol. 13(20), pages 1-27, October.
    8. Mehrgoo, Morteza & Amidpour, Majid, 2017. "Constructal design and optimization of a dual pressure heat recovery steam generator," Energy, Elsevier, vol. 124(C), pages 87-99.
    9. Zhe Xu & Yingqing Guo & Haotian Mao & Fuqiang Yang, 2019. "Configuration Optimization and Performance Comparison of STHX-DDB and STHX-SB by A Multi-Objective Genetic Algorithm," Energies, MDPI, vol. 12(9), pages 1-20, May.
    10. Feng, Huijun & Xie, Zhuojun & Chen, Lingen & Wu, Zhixiang & Xia, Shaojun, 2020. "Constructal design for supercharged boiler superheater," Energy, Elsevier, vol. 191(C).
    11. Shuangshuang Shi & Yanlin Ge & Lingen Chen & Huijun Feng, 2021. "Performance Optimizations with Single-, Bi-, Tri-, and Quadru-Objective for Irreversible Atkinson Cycle with Nonlinear Variation of Working Fluid’s Specific Heat," Energies, MDPI, vol. 14(14), pages 1-23, July.
    12. Jing-Hui Meng & Hao-Chi Wu & Tian-Hu Wang, 2019. "Optimization of Two-Stage Combined Thermoelectric Devices by a Three-Dimensional Multi-Physics Model and Multi-Objective Genetic Algorithm," Energies, MDPI, vol. 12(14), pages 1-24, July.
    13. Mohammad Hossein Ahmadi & Mohammad Ali Ahmadi & Arash Shafaei & Milad Ashouri & Somayeh Toghyani, 2016. "Thermodynamic analysis and optimization of the Atkinson engine by using NSGA-II," International Journal of Low-Carbon Technologies, Oxford University Press, vol. 11(3), pages 317-324.
    14. Shahriyar Abedinnezhad & Mohammad Hossein Ahmadi & Seyed Mohsen Pourkiaei & Fathollah Pourfayaz & Amir Mosavi & Michel Feidt & Shahaboddin Shamshirband, 2019. "Thermodynamic Assessment and Multi-Objective Optimization of Performance of Irreversible Dual-Miller Cycle," Energies, MDPI, vol. 12(20), pages 1-25, October.
    15. Xiao, Wu & Wang, Kaifeng & Jiang, Xiaobin & Li, Xiangcun & Wu, Xuemei & Hao, Ze & He, Gaohong, 2019. "Simultaneous optimization strategies for heat exchanger network synthesis and detailed shell-and-tube heat-exchanger design involving phase changes using GA/SA," Energy, Elsevier, vol. 183(C), pages 1166-1177.
    16. Lingen Chen & Chenqi Tang & Huijun Feng & Yanlin Ge, 2020. "Power, Efficiency, Power Density and Ecological Function Optimization for an Irreversible Modified Closed Variable-Temperature Reservoir Regenerative Brayton Cycle with One Isothermal Heating Process," Energies, MDPI, vol. 13(19), pages 1-23, October.
    17. Wang, Lingbao & Bu, Xianbiao & Li, Huashan, 2020. "Multi-objective optimization and off-design evaluation of organic rankine cycle (ORC) for low-grade waste heat recovery," Energy, Elsevier, vol. 203(C).
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Huijun Feng & Lingen Chen & Wei Tang & Yanlin Ge, 2022. "Optimal Design of a Dual-Pressure Steam Turbine for Rankine Cycle Based on Constructal Theory," Energies, MDPI, vol. 15(13), pages 1-20, July.
    2. Yang, Wenhao & Feng, Huijun & Chen, Lingen & Ge, Yanlin, 2023. "Power and efficiency optimizations of a simple irreversible supercritical organic Rankine cycle," Energy, Elsevier, vol. 278(C).
    3. Hongwei Zhu & Lingen Chen & Yanlin Ge & Shuangshuang Shi & Huijun Feng, 2022. "Multi-Objective Constructal Design for Square Heat-Generation Body with “Arrow-Shaped” High-Thermal-Conductivity Channel," Energies, MDPI, vol. 15(14), pages 1-15, July.
    4. Li, Zhaojin & Bi, Yuehong & Wang, Cun & Shi, Qi & Mou, Tianhong, 2023. "Finite time thermodynamic optimization for performance of absorption energy storage systems," Energy, Elsevier, vol. 282(C).
    5. Canpolat Tosun, Demet & Açıkkalp, Emin & Altuntas, Onder & Hepbasli, Arif & Palmero-Marrero, Ana I. & Borge-Diez, David, 2023. "Dynamic performance and sustainability assessment of a PV driven Carnot battery," Energy, Elsevier, vol. 278(C).
    6. Mao, Liangjie & Wei, Changjiang & Zeng, Song & Cai, Mingjie, 2023. "Heat transfer mechanism of cold-water pipe in ocean thermal energy conversion system," Energy, Elsevier, vol. 269(C).
    7. Niu, Jintao & Wang, Jiansheng & Liu, Xueling, 2023. "Thermodynamic and economic analysis of organic Rankine cycle combined with flash cycle and ejector," Energy, Elsevier, vol. 282(C).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Tang, Wei & Feng, Huijun & Chen, Lingen & Xie, Zhuojun & Shi, Junchao, 2021. "Constructal design for a boiler economizer," Energy, Elsevier, vol. 223(C).
    2. Pengchao Zang & Lingen Chen & Yanlin Ge, 2022. "Maximizing Efficient Power for an Irreversible Porous Medium Cycle with Nonlinear Variation of Working Fluid’s Specific Heat," Energies, MDPI, vol. 15(19), pages 1-12, September.
    3. Shuozhuo Hu & Zhen Yang & Jian Li & Yuanyuan Duan, 2021. "A Review of Multi-Objective Optimization in Organic Rankine Cycle (ORC) System Design," Energies, MDPI, vol. 14(20), pages 1-36, October.
    4. Huijun Feng & Lingen Chen & Wei Tang & Yanlin Ge, 2022. "Optimal Design of a Dual-Pressure Steam Turbine for Rankine Cycle Based on Constructal Theory," Energies, MDPI, vol. 15(13), pages 1-20, July.
    5. Feng, Huijun & Xie, Zhuojun & Chen, Lingen & Wu, Zhixiang & Xia, Shaojun, 2020. "Constructal design for supercharged boiler superheater," Energy, Elsevier, vol. 191(C).
    6. Wu, Zhixiang & Feng, Huijun & Chen, Lingen & Xie, Zhuojun & Cai, Cunguang, 2019. "Pumping power minimization of an evaporator in ocean thermal energy conversion system based on constructal theory," Energy, Elsevier, vol. 181(C), pages 974-984.
    7. Niu, Jintao & Wang, Jiansheng & Liu, Xueling, 2023. "Thermodynamic and economic analysis of organic Rankine cycle combined with flash cycle and ejector," Energy, Elsevier, vol. 282(C).
    8. Xiao, Wu & Cheng, Andi & Li, Shuai & Jiang, Xiaobin & Ruan, Xuehua & He, Gaohong, 2021. "A multi-objective optimization strategy of steam power system to achieve standard emission and optimal economic by NSGA-Ⅱ," Energy, Elsevier, vol. 232(C).
    9. Dongliang Li & Shaojun Xia & Jianghua Geng & Fankai Meng & Yutao Chen & Guoqing Zhu, 2022. "Discriminability Analysis of Characterization Parameters in Micro-Leakage of Turbocharged Boiler’s Evaporation Tube," Energies, MDPI, vol. 15(22), pages 1-20, November.
    10. Ge, Yanlin & Wu, Heng & Chen, Lingen & Feng, Huijun & Xie, Zhihui, 2023. "Finite time and finite speed thermodynamic optimization for an irreversible Atkinson cycle," Energy, Elsevier, vol. 270(C).
    11. Zhu, Meng & Zhou, Jing & Chen, Lei & Su, Sheng & Hu, Song & Qing, Haoran & Li, Aishu & Wang, Yi & Zhong, Wenqi & Xiang, Jun, 2022. "Economic analysis and cost modeling of supercritical CO2 coal-fired boiler based on global optimization," Energy, Elsevier, vol. 239(PD).
    12. Guangbiao Fu & Songyuan Zhang & Zhong Ge & Jian Li & Jian Xu & Jianbin Xie & Zhiyong Xie & Dong Yao & Tao Zhao & Zhijie Wang & Shuaikun Yue & Siyu Zhao & Fanhan Liu & Qiuping Jiang, 2022. "Thermo-Economic Performance Analysis of a Novel Organic Flash Rankine Cycle Using R600/R245fa Mixtures," Energies, MDPI, vol. 15(21), pages 1-19, October.
    13. Chen, Lingen & Shi, Shuangshuang & Ge, Yanlin & Feng, Huijun, 2023. "Ecological function performance analysis and multi-objective optimization for an endoreversible four-reservoir chemical pump," Energy, Elsevier, vol. 282(C).
    14. Li, Guolong & Li, Yanjun & Fang, Chengyue & Su, Jian & Wang, Haotong & Sun, Shengdi & Zhang, Guolei & Shi, Jianxin, 2023. "Research on fault diagnosis of supercharged boiler with limited data based on few-shot learning," Energy, Elsevier, vol. 281(C).
    15. Mazzetti, Marit J. & Hagen, Brede A.L. & Skaugen, Geir & Lindqvist, Karl & Lundberg, Steinar & Kristensen, Oddrun A., 2021. "Achieving 50% weight reduction of offshore steam bottoming cycles," Energy, Elsevier, vol. 230(C).
    16. Aljaghtham, Mutabe & Celik, Emrah, 2020. "Design optimization of oil pan thermoelectric generator to recover waste heat from internal combustion engines," Energy, Elsevier, vol. 200(C).
    17. Ping, Xu & Yang, Fubin & Zhang, Hongguang & Xing, Chengda & Zhang, Wujie & Wang, Yan & Yao, Baofeng, 2023. "Dynamic response assessment and multi-objective optimization of organic Rankine cycle (ORC) under vehicle driving cycle conditions," Energy, Elsevier, vol. 263(PA).
    18. Ahmadi, Mohammad H. & Ahmadi, Mohammad-Ali & Maleki, Akbar & Pourfayaz, Fathollah & Bidi, Mokhtar & Açıkkalp, Emin, 2017. "Exergetic sustainability evaluation and multi-objective optimization of performance of an irreversible nanoscale Stirling refrigeration cycle operating with Maxwell–Boltzmann gas," Renewable and Sustainable Energy Reviews, Elsevier, vol. 78(C), pages 80-92.
    19. Li, You-Rong & Du, Mei-Tang & Wu, Shuang-Ying & Peng, Lan & Liu, Chao, 2012. "Exergoeconomic analysis and optimization of a condenser for a binary mixture of vapors in organic Rankine cycle," Energy, Elsevier, vol. 40(1), pages 341-347.
    20. Zhe Xu & Yingqing Guo & Huarui Yang & Haotian Mao & Zongling Yu & Rui Li, 2020. "One Convenient Method to Calculate Performance and Optimize Configuration for Annular Radiator Using Heat Transfer Unit Simulation," Energies, MDPI, vol. 13(1), pages 1-19, January.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:14:y:2021:i:17:p:5545-:d:629434. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.