IDEAS home Printed from https://ideas.repec.org/a/eee/rensus/v141y2021ics136403212100112x.html
   My bibliography  Save this article

Effects of enhanced fuel with Mg-doped Fe3O4 nanoparticles on combustion of a compression ignition engine: Influence of Mg cation concentration

Author

Listed:
  • Sarvestani, Nasrin Sabet
  • Tabasizadeh, Mohammad
  • Abbaspour Fard, Mohammad Hossein
  • Nayebzadeh, Hamed
  • Van, Thuy Chu
  • Jafari, Mohammad
  • Bodisco, Timothy A.
  • Ristovski, Zoran
  • Brown, Richard J.

Abstract

The present study focuses on the synthesis of novel catalytic nanoparticles and their effect on combustion, performance, and emission characteristics of a diesel engine. For this purpose, Mg cations were doped into a Fe3O4 lattice to form MgxFe(3-x)O4 (x = 0.25, 0.5, 0.75, and 1) using a solution combustion method. Comprehensive characterization studies were carried out to assess the oxygen storage capacity (OSC) and the properties of final powders. These synthesized samples were dispersed in a diesel-biodiesel blend fuel with a concentration of 90 ppm. Assessment of the structure of the samples proved the formation of MgFe2O4 structures, suggesting that Mg cations were embedded into the Fe3O4 and formed appropriate structures. The OSC was reduced from 8661 μmol/g (Mg0·25Fe2·75O4) to 7069 μmol/g (MgFe2O4) by introducing additional Mg cations. When run on a six-cylinder diesel engine, the fuel mixed from the synthesized samples did not significantly influence the indicated power (IP), brake specific fuel consumption (BSFC) or the brake thermal efficiency (BTE). In addition to the obtained result for the OSC of the sample, which declined by increasing the Mg concentration in the Fe3O4 lattice, using the sample with the highest concentration of Mg cations, a considerable reduction was detected in the major exhaust emissions such as HC (56.5%), PM1 (35%), and PN (37%) and a slight decrease occurred in CO (7%) compared to the engine fueled by pure fuel. Based on the experimental engine results, the MgFe2O4 sample can be considered as a useful nanocatalyst for mixing in the fuels for emissions reduction.

Suggested Citation

  • Sarvestani, Nasrin Sabet & Tabasizadeh, Mohammad & Abbaspour Fard, Mohammad Hossein & Nayebzadeh, Hamed & Van, Thuy Chu & Jafari, Mohammad & Bodisco, Timothy A. & Ristovski, Zoran & Brown, Richard J., 2021. "Effects of enhanced fuel with Mg-doped Fe3O4 nanoparticles on combustion of a compression ignition engine: Influence of Mg cation concentration," Renewable and Sustainable Energy Reviews, Elsevier, vol. 141(C).
    • Handle: RePEc:eee:rensus:v:141:y:2021:i:c:s136403212100112x
    DOI: 10.1016/j.rser.2021.110817
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S136403212100112X
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.rser.2021.110817?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Kumar, Shiva & Dinesha, P. & Ajay, C.M. & Kabbur, Poojitha, 2020. "Combined effect of oxygenated liquid and metal oxide nanoparticle fuel additives on the combustion characteristics of a biodiesel engine operated with higher blend percentages," Energy, Elsevier, vol. 197(C).
    2. Nayebzadeh, Hamed & Haghighi, Mohammad & Saghatoleslami, Naser & Alaei, Shervin & Yousefi, Sina, 2019. "Texture/phase evolution during plasma treatment of microwave-combustion synthesized KOH/Ca12Al14O33-C nanocatalyst for reusability enhancement in conversion of canola oil to biodiesel," Renewable Energy, Elsevier, vol. 139(C), pages 28-39.
    3. Sorrell, Steve, 2015. "Reducing energy demand: A review of issues, challenges and approaches," Renewable and Sustainable Energy Reviews, Elsevier, vol. 47(C), pages 74-82.
    4. Kannan, G.R. & Karvembu, R. & Anand, R., 2011. "Effect of metal based additive on performance emission and combustion characteristics of diesel engine fuelled with biodiesel," Applied Energy, Elsevier, vol. 88(11), pages 3694-3703.
    5. Gürü, Metin & Koca, Atilla & Can, Özer & Çınar, Can & Şahin, Fatih, 2010. "Biodiesel production from waste chicken fat based sources and evaluation with Mg based additive in a diesel engine," Renewable Energy, Elsevier, vol. 35(3), pages 637-643.
    6. Ettefaghi, Ehsanollah & Ghobadian, Barat & Rashidi, Alimorad & Najafi, G. & Khoshtaghaza, Mohammad Hadi & Rashtchi, Maryam & Sadeghian, Sina, 2018. "A novel bio-nano emulsion fuel based on biodegradable nanoparticles to improve diesel engines performance and reduce exhaust emissions," Renewable Energy, Elsevier, vol. 125(C), pages 64-72.
    7. Ma, Yu & Zhu, Mingming & Zhang, Dongke, 2013. "The effect of a homogeneous combustion catalyst on exhaust emissions from a single cylinder diesel engine," Applied Energy, Elsevier, vol. 102(C), pages 556-562.
    8. Talebizadeh, P. & Babaie, M. & Brown, R. & Rahimzadeh, H. & Ristovski, Z. & Arai, M., 2014. "The role of non-thermal plasma technique in NOx treatment: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 40(C), pages 886-901.
    9. E, Jiaqiang & Pham, Minhhieu & Zhao, D. & Deng, Yuanwang & Le, DucHieu & Zuo, Wei & Zhu, Hao & Liu, Teng & Peng, Qingguo & Zhang, Zhiqing, 2017. "Effect of different technologies on combustion and emissions of the diesel engine fueled with biodiesel: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 80(C), pages 620-647.
    10. Saxena, Vishal & Kumar, Niraj & Saxena, Vinod.Kumar, 2017. "A comprehensive review on combustion and stability aspects of metal nanoparticles and its additive effect on diesel and biodiesel fuelled C.I. engine," Renewable and Sustainable Energy Reviews, Elsevier, vol. 70(C), pages 563-588.
    11. Zare, Ali & Bodisco, Timothy A. & Nabi, Md Nurun & Hossain, Farhad M. & Rahman, M.M. & Ristovski, Zoran D. & Brown, Richard J., 2017. "The influence of oxygenated fuels on transient and steady-state engine emissions," Energy, Elsevier, vol. 121(C), pages 841-853.
    12. Hoseini, S.S. & Najafi, G. & Ghobadian, B. & Mamat, Rizalman & Sidik, Nor Azwadi Che & Azmi, W.H., 2017. "The effect of combustion management on diesel engine emissions fueled with biodiesel-diesel blends," Renewable and Sustainable Energy Reviews, Elsevier, vol. 73(C), pages 307-331.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. El-Seesy, Ahmed I. & Hassan, Hamdy & Ookawara, S., 2018. "Effects of graphene nanoplatelet addition to jatropha Biodiesel–Diesel mixture on the performance and emission characteristics of a diesel engine," Energy, Elsevier, vol. 147(C), pages 1129-1152.
    2. Hoseini, S.S. & Najafi, G. & Ghobadian, B. & Mamat, R. & Ebadi, M.T. & Yusaf, Talal, 2018. "Novel environmentally friendly fuel: The effects of nanographene oxide additives on the performance and emission characteristics of diesel engines fuelled with Ailanthus altissima biodiesel," Renewable Energy, Elsevier, vol. 125(C), pages 283-294.
    3. Saxena, Vishal & Kumar, Niraj & Saxena, Vinod Kumar, 2019. "Multi-objective optimization of modified nanofluid fuel blends at different TiO2 nanoparticle concentration in diesel engine: Experimental assessment and modeling," Applied Energy, Elsevier, vol. 248(C), pages 330-353.
    4. Liang, Daolun & Ren, Ke & Wu, Zizhan & Jiang, Yangxu & Shen, Dekui & Li, Heping & Liu, Jianzhong, 2021. "Combustion characteristics of oxygenated slurry droplets of nano-Al/EtOH and nano-Al/TPGME blends," Energy, Elsevier, vol. 220(C).
    5. Solmaz, Hamit & Ardebili, Seyed Mohammad Safieddin & Calam, Alper & Yılmaz, Emre & İpci, Duygu, 2021. "Prediction of performance and exhaust emissions of a CI engine fueled with multi-wall carbon nanotube doped biodiesel-diesel blends using response surface method," Energy, Elsevier, vol. 227(C).
    6. Hoseini, S.S. & Najafi, G. & Ghobadian, B. & Mamat, R. & Ebadi, M.T. & Yusaf, Talal, 2019. "Characterization of biodiesel production (ultrasonic-assisted) from evening-primroses (Oenothera lamarckiana) as novel feedstock and its effect on CI engine parameters," Renewable Energy, Elsevier, vol. 130(C), pages 50-60.
    7. Ayhan, Vezir & Ece, Yılmaz Mert, 2020. "New application to reduce NOx emissions of diesel engines: Electronically controlled direct water injection at compression stroke," Applied Energy, Elsevier, vol. 260(C).
    8. EL-Seesy, Ahmed I. & Hassan, Hamdy, 2019. "Investigation of the effect of adding graphene oxide, graphene nanoplatelet, and multiwalled carbon nanotube additives with n-butanol-Jatropha methyl ester on a diesel engine performance," Renewable Energy, Elsevier, vol. 132(C), pages 558-574.
    9. Das, Amar Kumar & Sahu, Santosh Kumar & Panda, Achyut Kumar, 2022. "Current status and prospects of alternate liquid transportation fuels in compression ignition engines: A critical review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 161(C).
    10. Mofijur, M. & Atabani, A.E. & Masjuki, H.H. & Kalam, M.A. & Masum, B.M., 2013. "A study on the effects of promising edible and non-edible biodiesel feedstocks on engine performance and emissions production: A comparative evaluation," Renewable and Sustainable Energy Reviews, Elsevier, vol. 23(C), pages 391-404.
    11. Zhang, Zhi-Hui & Balasubramanian, Rajasekhar, 2015. "Influence of an iron-based fuel-borne catalyst on physicochemical and toxicological characteristics of particulate emissions from a diesel engine," Applied Energy, Elsevier, vol. 146(C), pages 270-278.
    12. E, Jiaqiang & Pham, Minhhieu & Zhao, D. & Deng, Yuanwang & Le, DucHieu & Zuo, Wei & Zhu, Hao & Liu, Teng & Peng, Qingguo & Zhang, Zhiqing, 2017. "Effect of different technologies on combustion and emissions of the diesel engine fueled with biodiesel: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 80(C), pages 620-647.
    13. Sarah Oluwabunmi Bitire & Emeka Charles Nwanna & Tien-Chien Jen, 2023. "The impact of CuO nanoparticles as fuel additives in biodiesel-blend fuelled diesel engine: A review," Energy & Environment, , vol. 34(7), pages 2259-2289, November.
    14. Kumar, Shiva & Dinesha, P. & Bran, Ijas, 2017. "Influence of nanoparticles on the performance and emission characteristics of a biodiesel fuelled engine: An experimental analysis," Energy, Elsevier, vol. 140(P1), pages 98-105.
    15. Mat Yasin, Mohd Hafizil & Mamat, Rizalman & Najafi, G. & Ali, Obed Majeed & Yusop, Ahmad Fitri & Ali, Mohd Hafiz, 2017. "Potentials of palm oil as new feedstock oil for a global alternative fuel: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 79(C), pages 1034-1049.
    16. Saxena, Vishal & Kumar, Niraj & Saxena, Vinod.Kumar, 2017. "A comprehensive review on combustion and stability aspects of metal nanoparticles and its additive effect on diesel and biodiesel fuelled C.I. engine," Renewable and Sustainable Energy Reviews, Elsevier, vol. 70(C), pages 563-588.
    17. Ashok, B. & Nanthagopal, K. & Mohan, Aravind & Johny, Ajith & Tamilarasu, A., 2017. "Comparative analysis on the effect of zinc oxide and ethanox as additives with biodiesel in CI engine," Energy, Elsevier, vol. 140(P1), pages 352-364.
    18. Tadeusz Dziubak & Mirosław Karczewski, 2022. "Experimental Studies of the Effect of Air Filter Pressure Drop on the Composition and Emission Changes of a Compression Ignition Internal Combustion Engine," Energies, MDPI, vol. 15(13), pages 1-31, June.
    19. Kumar, Shiva & Dinesha, P. & Rosen, Marc A., 2019. "Effect of injection pressure on the combustion, performance and emission characteristics of a biodiesel engine with cerium oxide nanoparticle additive," Energy, Elsevier, vol. 185(C), pages 1163-1173.
    20. Sam Ki Yoon & Jun Cong Ge & Nag Jung Choi, 2019. "Influence of Fuel Injection Pressure on the Emissions Characteristics and Engine Performance in a CRDI Diesel Engine Fueled with Palm Biodiesel Blends," Energies, MDPI, vol. 12(20), pages 1-16, October.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:rensus:v:141:y:2021:i:c:s136403212100112x. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.elsevier.com/wps/find/journaldescription.cws_home/600126/description#description .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.