IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v13y2020i24p6739-d465648.html
   My bibliography  Save this article

Multi-Objective Optimization of Solar Thermal Systems Applied to Portuguese Dwellings

Author

Listed:
  • Ana Cristina Ferreira

    (MEtRICs Research Centre, University of Minho, 4804-533 Guimarães, Portugal)

  • Angela Silva

    (Escola Superior de Ciências Empresariais, Instituto Politécnico de Viana do Castelo, 4930-600 Valença, Portugal)

  • José Carlos Teixeira

    (MEtRICs Research Centre, University of Minho, 4804-533 Guimarães, Portugal)

  • Senhorinha Teixeira

    (ALGORITMI Research Centre, University of Minho, 4804-533 Guimarães, Portugal)

Abstract

Solar thermal systems have been widely used to increase energy efficiency in the building sector, since the use of renewable energy sources became one of the top priorities to meet environmental targets. The main objective of this study is the thermo-economic optimization of solar thermal systems for residential building applications, considering a multi-objective approach. The simulations were performed through a MatLab code by implementing an elitist variant of Non-dominated Sorting Genetic Algorithm-II (NASGA-II). The solar collection area and the linear loss coefficient as well as the tank storage volume were defined as decision variables. A two-dimensional Pareto front was obtained, considering as objective functions the minimization of the annualized investment cost and the maximization of the solar collection efficiency. Based on the best trade-off between both objectives and considering that the solar thermal systems can operate for a period of at least 15 years, the Pareto analysis led to the conclusion that a system with an annualized investment cost between 270 and 280 €/year allows reaching a collection efficiency of 60%. After the analysis of the optimal solution points, a configuration was selected to estimate the system total purchasing cost: a panel with a solar area of 4.17 m 2 and with a linear coefficient loss of 3.684 W/m 2 .K; a storage volume of 0.275 m 3 ; and a pump flow rate of 0.1364 m 3 /h. For this configuration, we estimated a total purchasing cost of 2545.0 €, whereas the solar collector and the storage tank are the most expensive components, representing a share of 42% and 43%, respectively. These results represent a specific cost of 610.3 €/m 2 per solar collection area.

Suggested Citation

  • Ana Cristina Ferreira & Angela Silva & José Carlos Teixeira & Senhorinha Teixeira, 2020. "Multi-Objective Optimization of Solar Thermal Systems Applied to Portuguese Dwellings," Energies, MDPI, vol. 13(24), pages 1-23, December.
    • Handle: RePEc:gam:jeners:v:13:y:2020:i:24:p:6739-:d:465648
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/13/24/6739/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/13/24/6739/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Lazzaretto, Andrea & Tsatsaronis, George, 2006. "SPECO: A systematic and general methodology for calculating efficiencies and costs in thermal systems," Energy, Elsevier, vol. 31(8), pages 1257-1289.
    2. Attonaty, Kévin & Pouvreau, Jérôme & Deydier, Alexandre & Oriol, Jean & Stouffs, Pascal, 2020. "Thermodynamic and economic evaluation of an innovative electricity storage system based on thermal energy storage," Renewable Energy, Elsevier, vol. 150(C), pages 1030-1036.
    3. Antoniadis, Christodoulos N. & Martinopoulos, Georgios, 2019. "Optimization of a building integrated solar thermal system with seasonal storage using TRNSYS," Renewable Energy, Elsevier, vol. 137(C), pages 56-66.
    4. Khamis Mansour, M., 2013. "Thermal analysis of novel minichannel-based solar flat-plate collector," Energy, Elsevier, vol. 60(C), pages 333-343.
    5. Karki, Saroj & Haapala, Karl R. & Fronk, Brian M., 2019. "Technical and economic feasibility of solar flat-plate collector thermal energy systems for small and medium manufacturers," Applied Energy, Elsevier, vol. 254(C).
    6. Dimitris Al. Katsaprakakis & Georgios Zidianakis & Yiannis Yiannakoudakis & Evaggelos Manioudakis & Irini Dakanali & Spyros Kanouras, 2020. "Working on Buildings’ Energy Performance Upgrade in Mediterranean Climate," Energies, MDPI, vol. 13(9), pages 1-28, May.
    7. Chen, C.Q. & Diao, Y.H. & Zhao, Y.H. & Wang, Z.Y. & Liang, L. & Wang, T.Y. & Zhu, T.T. & Ma, C., 2020. "Thermal performance of a closed collector–storage solar air heating system with latent thermal storage: An experimental study," Energy, Elsevier, vol. 202(C).
    8. Marion, Michaël & Voicu, Ionut & Tiffonnet, Anne-Lise, 2012. "Study and optimization of a solar subcritical organic Rankine cycle," Renewable Energy, Elsevier, vol. 48(C), pages 100-109.
    9. Sami, S. & Semmar, D. & Hamid, A. & Mecheri, R. & Yaiche, M., 2018. "Viability of integrating Solar Water Heating systems into High Energy Performance housing in Algeria," Energy, Elsevier, vol. 149(C), pages 354-363.
    10. Tsilingiridis, G. & Martinopoulos, G., 2010. "Thirty years of domestic solar hot water systems use in Greece – energy and environmental benefits – future perspectives," Renewable Energy, Elsevier, vol. 35(2), pages 490-497.
    11. Islam, Md. Parvez & Morimoto, Tetsuo, 2018. "Advances in low to medium temperature non-concentrating solar thermal technology," Renewable and Sustainable Energy Reviews, Elsevier, vol. 82(P3), pages 2066-2093.
    12. Ferreira, Ana C.M. & Nunes, Manuel L. & Teixeira, Senhorinha F.C.F. & Leão, Celina P. & Silva, Ângela M. & Teixeira, José C.F. & Martins, Luís A.S.B., 2012. "An economic perspective on the optimisation of a small-scale cogeneration system for the Portuguese scenario," Energy, Elsevier, vol. 45(1), pages 436-444.
    13. Andrea Frattolillo & Laura Canale & Giorgio Ficco & Costantino C. Mastino & Marco Dell’Isola, 2020. "Potential for Building Façade-Integrated Solar Thermal Collectors in a Highly Urbanized Context," Energies, MDPI, vol. 13(21), pages 1-18, November.
    14. Gautam, Abhishek & Chamoli, Sunil & Kumar, Alok & Singh, Satyendra, 2017. "A review on technical improvements, economic feasibility and world scenario of solar water heating system," Renewable and Sustainable Energy Reviews, Elsevier, vol. 68(P1), pages 541-562.
    15. Tschopp, Daniel & Tian, Zhiyong & Berberich, Magdalena & Fan, Jianhua & Perers, Bengt & Furbo, Simon, 2020. "Large-scale solar thermal systems in leading countries: A review and comparative study of Denmark, China, Germany and Austria," Applied Energy, Elsevier, vol. 270(C).
    16. Cruz-Peragon, F. & Palomar, J.M. & Casanova, P.J. & Dorado, M.P. & Manzano-Agugliaro, F., 2012. "Characterization of solar flat plate collectors," Renewable and Sustainable Energy Reviews, Elsevier, vol. 16(3), pages 1709-1720.
    17. Martinopoulos, G. & Tsalikis, G., 2018. "Diffusion and adoption of solar energy conversion systems – The case of Greece," Energy, Elsevier, vol. 144(C), pages 800-807.
    18. Tian, Y. & Zhao, C.Y., 2013. "A review of solar collectors and thermal energy storage in solar thermal applications," Applied Energy, Elsevier, vol. 104(C), pages 538-553.
    19. Lin, Wenye & Ma, Zhenjun & Ren, Haoshan & Gschwander, Stefan & Wang, Shugang, 2019. "Multi-objective optimisation of thermal energy storage using phase change materials for solar air systems," Renewable Energy, Elsevier, vol. 130(C), pages 1116-1129.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Grzegorz Ostasz & Dominika Siwiec & Andrzej Pacana, 2022. "Universal Model to Predict Expected Direction of Products Quality Improvement," Energies, MDPI, vol. 15(5), pages 1-18, February.
    2. Jaroslav Košičan & Miguel Ángel Pardo Picazo & Silvia Vilčeková & Danica Košičanová, 2021. "Life Cycle Assessment and Economic Energy Efficiency of a Solar Thermal Installation in a Family House," Sustainability, MDPI, vol. 13(4), pages 1-19, February.
    3. Omais Abdur Rehman & Valeria Palomba & Andrea Frazzica & Antonios Charalampidis & Sotirios Karellas & Luisa F. Cabeza, 2023. "Numerical and Experimental Analysis of a Low-GWP Heat Pump Coupled to Electrical and Thermal Energy Storage to Increase the Share of Renewables across Europe," Sustainability, MDPI, vol. 15(6), pages 1-33, March.
    4. Lorenzo Gragnaniello & Marcello Iasiello & Gerardo Maria Mauro, 2022. "Multi-Objective Optimization of a Heat Sink for the Thermal Management of a Peltier-Cell-Based Biomedical Refrigerator," Energies, MDPI, vol. 15(19), pages 1-12, October.
    5. Andrzej Pacana & Dominika Siwiec, 2022. "Model to Predict Quality of Photovoltaic Panels Considering Customers’ Expectations," Energies, MDPI, vol. 15(3), pages 1-33, February.
    6. Dominika Siwiec & Andrzej Pacana, 2021. "Model of Choice Photovoltaic Panels Considering Customers’ Expectations," Energies, MDPI, vol. 14(18), pages 1-32, September.
    7. PELELLA, Francesco & ZSEMBINSZKI, Gabriel & VISCITO, Luca & William MAURO, Alfonso & CABEZA, Luisa F., 2023. "Thermo-economic optimization of a multi-source (air/sun/ground) residential heat pump with a water/PCM thermal storage," Applied Energy, Elsevier, vol. 331(C).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Evangelisti, Luca & De Lieto Vollaro, Roberto & Asdrubali, Francesco, 2019. "Latest advances on solar thermal collectors: A comprehensive review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 114(C), pages 1-1.
    2. Selikhov, Yuriy & Klemeš, Jiří Jaromír & Kapustenko, Petro & Arsenyeva, Olga, 2022. "The study of flat plate solar collector with absorbing elements from a polymer material," Energy, Elsevier, vol. 256(C).
    3. Zhang, Tongtong & She, Xiaohui & You, Zhanping & Zhao, Yanqi & Fan, Hongjun & Ding, Yulong, 2022. "Cryogenic thermoelectric generation using cold energy from a decoupled liquid air energy storage system for decentralised energy networks," Applied Energy, Elsevier, vol. 305(C).
    4. Laveet Kumar & Junaid Ahmed & Mamdouh El Haj Assad & M. Hasanuzzaman, 2022. "Prospects and Challenges of Solar Thermal for Process Heating: A Comprehensive Review," Energies, MDPI, vol. 15(22), pages 1-27, November.
    5. Verma, Sujit Kumar & Sharma, Kamal & Gupta, Naveen Kumar & Soni, Pawan & Upadhyay, Neeraj, 2020. "“Performance comparison of innovative spiral shaped solar collector design with conventional flat plate solar collector”," Energy, Elsevier, vol. 194(C).
    6. Laura Canale & Anna Rita Di Fazio & Mario Russo & Andrea Frattolillo & Marco Dell’Isola, 2021. "An Overview on Functional Integration of Hybrid Renewable Energy Systems in Multi-Energy Buildings," Energies, MDPI, vol. 14(4), pages 1-33, February.
    7. Mohammad Al-Smairan & Moayyad Shawaqfah & Fares AlMomani, 2020. "Techno-Economic Investigation of an Integrated Boiler–Solar Water Heating/Cooling System: A Case Study," Energies, MDPI, vol. 14(1), pages 1-18, December.
    8. Islam, Md. Parvez & Morimoto, Tetsuo, 2018. "Advances in low to medium temperature non-concentrating solar thermal technology," Renewable and Sustainable Energy Reviews, Elsevier, vol. 82(P3), pages 2066-2093.
    9. Ismail, Muhammad Imran & Yunus, Nor Alafiza & Hashim, Haslenda, 2021. "Integration of solar heating systems for low-temperature heat demand in food processing industry – A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 147(C).
    10. Alessandro Franco, 2020. "Methods for the Sustainable Design of Solar Energy Systems for Industrial Process Heat," Sustainability, MDPI, vol. 12(12), pages 1-20, June.
    11. Gao, Datong & Kwan, Trevor Hocksun & Dabwan, Yousef Naji & Hu, Maobin & Hao, Yong & Zhang, Tao & Pei, Gang, 2022. "Seasonal-regulatable energy systems design and optimization for solar energy year-round utilization☆," Applied Energy, Elsevier, vol. 322(C).
    12. Zhou, Ruiwen & Ling, Xiang & Peng, Hao & Yang, Lin, 2018. "Thermal characteristics of the combined flat plate heat receiver in solar power tower plant," Energy, Elsevier, vol. 165(PA), pages 275-289.
    13. Miguel J. Prieto & Juan Á. Martínez & Rogelio Peón & Lourdes Á. Barcia & Fernando Nuño, 2017. "On the Convenience of Using Simulation Models to Optimize the Control Strategy of Molten-Salt Heat Storage Systems in Solar Thermal Power Plants," Energies, MDPI, vol. 10(7), pages 1-17, July.
    14. He, Chao & Liu, Chao & Zhou, Mengtong & Xie, Hui & Xu, Xiaoxiao & Wu, Shuangying & Li, Yourong, 2014. "A new selection principle of working fluids for subcritical organic Rankine cycle coupling with different heat sources," Energy, Elsevier, vol. 68(C), pages 283-291.
    15. Filipović, P. & Dović, D. & Horvat, I. & Ranilović, B., 2023. "Evaluation of a novel polymer solar collector using numerical and experimental methods," Energy, Elsevier, vol. 284(C).
    16. Oyekale, Joseph & Petrollese, Mario & Cau, Giorgio, 2020. "Modified auxiliary exergy costing in advanced exergoeconomic analysis applied to a hybrid solar-biomass organic Rankine cycle plant," Applied Energy, Elsevier, vol. 268(C).
    17. Carnevale, E. & Lombardi, L. & Zanchi, L., 2014. "Life Cycle Assessment of solar energy systems: Comparison of photovoltaic and water thermal heater at domestic scale," Energy, Elsevier, vol. 77(C), pages 434-446.
    18. Aikifa Raza & Jin-You Lu & Safa Alzaim & Hongxia Li & TieJun Zhang, 2018. "Novel Receiver-Enhanced Solar Vapor Generation: Review and Perspectives," Energies, MDPI, vol. 11(1), pages 1-29, January.
    19. Zhou, Liqun & Wang, Yiping & Huang, Qunwu, 2019. "Parametric analysis on the performance of flat plate collector with transparent insulation material," Energy, Elsevier, vol. 174(C), pages 534-542.
    20. Wang, Ruilin & Qu, Wanjun & Hong, Hui & Sun, Jie & Jin, Hongguang, 2018. "Experimental performance of 300 kWth prototype of parabolic trough collector with rotatable axis and irreversibility analysis," Energy, Elsevier, vol. 161(C), pages 595-609.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:13:y:2020:i:24:p:6739-:d:465648. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.