IDEAS home Printed from https://ideas.repec.org/a/eee/appene/v198y2017icp160-172.html
   My bibliography  Save this article

Designing the scale of a woody biomass CHP considering local forestry reformation: A case study of Tanegashima, Japan

Author

Listed:
  • Kanematsu, Yuichiro
  • Oosawa, Kazutake
  • Okubo, Tatsuya
  • Kikuchi, Yasunori

Abstract

Biomass has become a renewable resource for energy, but it needs continuous management to make it truly renewable. Planted forests in particular areas in the world are facing the challenges of reformation because of the severe maldistribution of forest age-classes caused by a stagnation in demand for wood or degradation by past deforestation. In these regions, the amount of wood processed and the overall biomass must be controlled by a schedule of forestry reformation. Particularly for energy plants, where a continuous and adequate supply of wood is required, the scale of the plants should be carefully designed to maintain a harmonized demand/supply balance in the region. In this study, we considered the scale design for a combined heating and power (CHP) system using woody biomass for district heating and cooling (DHC) in Tanegashima, a remote island in Japan, which requires immediate forestry reformation in addition to mitigating its fossil-fuel consumption. A process model representing material and energy flows associated with the life cycle of a biomass CHP system was developed, which considered the dependency of timber consumption on the scale of the CHP, together with other design parameters. The profile of the annual timber supply for the next 100years to achieve sustainable forestry planning was calculated, which became the constraint on the feasibility of resource procurement for CHP. The ratio between the maximum and minimum timber supply in the next 20years was determined to be about 1.8. Through simulation and life cycle assessment (LCA) using the developed model, CHP scales were specified to cover the overall heat and power demand of consumers for biomass-derived energy at 840kWe with 1470kWth. We found feasible and effective scale ranges for the various stages of forest-resource status by comparing LCA results, timber consumption, and profiles for timber supply. We have been able to demonstrate that woody biomass utilization in a specific area should address forestry reformation in a sustainable way.

Suggested Citation

  • Kanematsu, Yuichiro & Oosawa, Kazutake & Okubo, Tatsuya & Kikuchi, Yasunori, 2017. "Designing the scale of a woody biomass CHP considering local forestry reformation: A case study of Tanegashima, Japan," Applied Energy, Elsevier, vol. 198(C), pages 160-172.
    • Handle: RePEc:eee:appene:v:198:y:2017:i:c:p:160-172
    DOI: 10.1016/j.apenergy.2017.04.021
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0306261917304208
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.apenergy.2017.04.021?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Murphy, Fionnuala & Devlin, Ger & McDonnell, Kevin, 2014. "Forest biomass supply chains in Ireland: A life cycle assessment of GHG emissions and primary energy balances," Applied Energy, Elsevier, vol. 116(C), pages 1-8.
    2. Shimizu, Teruyuki & Kikuchi, Yasunori & Sugiyama, Hirokazu & Hirao, Masahiko, 2015. "Design method for a local energy cooperative network using distributed energy technologies," Applied Energy, Elsevier, vol. 154(C), pages 781-793.
    3. Puig-Arnavat, Maria & Bruno, Joan Carles & Coronas, Alberto, 2014. "Modeling of trigeneration configurations based on biomass gasification and comparison of performance," Applied Energy, Elsevier, vol. 114(C), pages 845-856.
    4. Michael Den Herder & Marja Kolström & Marcus Lindner & Tommi Suominen & Diana Tuomasjukka & Matias Pekkanen, 2012. "Sustainability Impact Assessment on the Production and Use of Different Wood and Fossil Fuels Employed for Energy Production in North Karelia, Finland," Energies, MDPI, vol. 5(11), pages 1-22, November.
    5. De Meyer, Annelies & Cattrysse, Dirk & Rasinmäki, Jussi & Van Orshoven, Jos, 2014. "Methods to optimise the design and management of biomass-for-bioenergy supply chains: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 31(C), pages 657-670.
    6. Ren, Hongbo & Zhou, Weisheng & Nakagami, Ken'ichi & Gao, Weijun, 2010. "Integrated design and evaluation of biomass energy system taking into consideration demand side characteristics," Energy, Elsevier, vol. 35(5), pages 2210-2222.
    7. Hendricks, Aaron M. & Wagner, John E. & Volk, Timothy A. & Newman, David H. & Brown, Tristan R., 2016. "A cost-effective evaluation of biomass district heating in rural communities," Applied Energy, Elsevier, vol. 162(C), pages 561-569.
    8. Sultana, Arifa & Kumar, Amit, 2012. "Optimal siting and size of bioenergy facilities using geographic information system," Applied Energy, Elsevier, vol. 94(C), pages 192-201.
    9. Ahmadi, Pouria & Dincer, Ibrahim & Rosen, Marc A., 2013. "Development and assessment of an integrated biomass-based multi-generation energy system," Energy, Elsevier, vol. 56(C), pages 155-166.
    10. Yasunori Kikuchi & Yuichiro Kanematsu & Masamichi Ugo & Yosuke Hamada & Tatsuya Okubo, 2016. "Industrial Symbiosis Centered on a Regional Cogeneration Power Plant Utilizing Available Local Resources: A Case Study of Tanegashima," Journal of Industrial Ecology, Yale University, vol. 20(2), pages 276-288, April.
    11. Shabani, Nazanin & Sowlati, Taraneh, 2013. "A mixed integer non-linear programming model for tactical value chain optimization of a wood biomass power plant," Applied Energy, Elsevier, vol. 104(C), pages 353-361.
    12. Krystel K. Castillo-Villar, 2014. "Metaheuristic Algorithms Applied to Bioenergy Supply Chain Problems: Theory, Review, Challenges, and Future," Energies, MDPI, vol. 7(11), pages 1-33, November.
    13. McIlveen-Wright, David R. & Huang, Ye & Rezvani, Sina & Redpath, David & Anderson, Mark & Dave, Ashok & Hewitt, Neil J., 2013. "A technical and economic analysis of three large scale biomass combustion plants in the UK," Applied Energy, Elsevier, vol. 112(C), pages 396-404.
    14. Tonini, Davide & Astrup, Thomas, 2012. "LCA of biomass-based energy systems: A case study for Denmark," Applied Energy, Elsevier, vol. 99(C), pages 234-246.
    15. Cambero, Claudia & Sowlati, Taraneh, 2014. "Assessment and optimization of forest biomass supply chains from economic, social and environmental perspectives – A review of literature," Renewable and Sustainable Energy Reviews, Elsevier, vol. 36(C), pages 62-73.
    16. Truong, Nguyen Le & Gustavsson, Leif, 2013. "Integrated biomass-based production of district heat, electricity, motor fuels and pellets of different scales," Applied Energy, Elsevier, vol. 104(C), pages 623-632.
    17. Vukašinović, Vladimir & Gordić, Dušan, 2016. "Optimization and GIS-based combined approach for the determination of the most cost-effective investments in biomass sector," Applied Energy, Elsevier, vol. 178(C), pages 250-259.
    18. Sacchelli, Sandro & De Meo, Isabella & Paletto, Alessandro, 2013. "Bioenergy production and forest multifunctionality: A trade-off analysis using multiscale GIS model in a case study in Italy," Applied Energy, Elsevier, vol. 104(C), pages 10-20.
    19. Md. Bedarul Alam & Reino Pulkki & Chander Shahi & Thakur Upadhyay, 2012. "Modeling Woody Biomass Procurement for Bioenergy Production at the Atikokan Generating Station in Northwestern Ontario, Canada," Energies, MDPI, vol. 5(12), pages 1-21, December.
    20. Huang, Y. & Wang, Y.D. & Chen, Haisheng & Zhang, Xinjing & Mondol, J. & Shah, N. & Hewitt, N.J., 2017. "Performance analysis of biofuel fired trigeneration systems with energy storage for remote households," Applied Energy, Elsevier, vol. 186(P3), pages 530-538.
    21. Sasaki, Nophea & Knorr, Wolfgang & Foster, David R. & Etoh, Hiroko & Ninomiya, Hiroshi & Chay, Sengtha & Kim, Sophanarith & Sun, Sengxi, 2009. "Woody biomass and bioenergy potentials in Southeast Asia between 1990 and 2020," Applied Energy, Elsevier, vol. 86(Supplemen), pages 140-150, November.
    22. Thakur, Amit & Canter, Christina E. & Kumar, Amit, 2014. "Life-cycle energy and emission analysis of power generation from forest biomass," Applied Energy, Elsevier, vol. 128(C), pages 246-253.
    23. Bracco, Stefano & Dentici, Gabriele & Siri, Silvia, 2013. "Economic and environmental optimization model for the design and the operation of a combined heat and power distributed generation system in an urban area," Energy, Elsevier, vol. 55(C), pages 1014-1024.
    24. Yasunori Kikuchi & Yuichiro Kanematsu & Ryuichi Sato & Takao Nakagaki, 2016. "Distributed Cogeneration of Power and Heat within an Energy Management Strategy for Mitigating Fossil Fuel Consumption," Journal of Industrial Ecology, Yale University, vol. 20(2), pages 289-303, April.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Santos, Andreia & Carvalho, Ana & Barbosa-Póvoa, Ana Paula & Marques, Alexandra & Amorim, Pedro, 2019. "Assessment and optimization of sustainable forest wood supply chains – A systematic literature review," Forest Policy and Economics, Elsevier, vol. 105(C), pages 112-135.
    2. Yamaki, Ayumi & Fujii, Shoma & Kanematsu, Yuichiro & Kikuchi, Yasunori, 2023. "Life cycle greenhouse gas emissions of cogeneration energy hubs at Japanese paper mills with thermal energy storage," Energy, Elsevier, vol. 270(C).
    3. Yamaki, Ayumi & Kanematsu, Yuichiro & Kikuchi, Yasunori, 2020. "Lifecycle greenhouse gas emissions of thermal energy storage implemented in a paper mill for wind energy utilization," Energy, Elsevier, vol. 205(C).
    4. Coady, Joe & Duquette, Jean, 2021. "Quantifying the impacts of biomass driven combined heat and power grids in northern rural and remote communities," Renewable and Sustainable Energy Reviews, Elsevier, vol. 148(C).
    5. Bacenetti, Jacopo, 2019. "Heat and cold production for winemaking using pruning residues: Environmental impact assessment," Applied Energy, Elsevier, vol. 252(C), pages 1-1.
    6. Carla L. Simões & Ricardo Simoes & Ana Sofia Gonçalves & Leonel J. R. Nunes, 2023. "Environmental Analysis of the Valorization of Woody Biomass Residues: A Comparative Study with Vine Pruning Leftovers in Portugal," Sustainability, MDPI, vol. 15(20), pages 1-16, October.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Vukasinovic, Vladimir & Gordic, Dusan & Zivkovic, Marija & Koncalovic, Davor & Zivkovic, Dubravka, 2019. "Long-term planning methodology for improving wood biomass utilization," Energy, Elsevier, vol. 175(C), pages 818-829.
    2. Durusut, Emrah & Tahir, Foaad & Foster, Sam & Dineen, Denis & Clancy, Matthew, 2018. "BioHEAT: A policy decision support tool in Ireland’s bioenergy and heat sectors," Applied Energy, Elsevier, vol. 213(C), pages 306-321.
    3. Cambero, Claudia & Sowlati, Taraneh, 2014. "Assessment and optimization of forest biomass supply chains from economic, social and environmental perspectives – A review of literature," Renewable and Sustainable Energy Reviews, Elsevier, vol. 36(C), pages 62-73.
    4. Saghaei, Mahsa & Ghaderi, Hadi & Soleimani, Hamed, 2020. "Design and optimization of biomass electricity supply chain with uncertainty in material quality, availability and market demand," Energy, Elsevier, vol. 197(C).
    5. Malladi, Krishna Teja & Sowlati, Taraneh, 2018. "Biomass logistics: A review of important features, optimization modeling and the new trends," Renewable and Sustainable Energy Reviews, Elsevier, vol. 94(C), pages 587-599.
    6. Vukašinović, Vladimir & Gordić, Dušan, 2016. "Optimization and GIS-based combined approach for the determination of the most cost-effective investments in biomass sector," Applied Energy, Elsevier, vol. 178(C), pages 250-259.
    7. Ba, Birome Holo & Prins, Christian & Prodhon, Caroline, 2016. "Models for optimization and performance evaluation of biomass supply chains: An Operations Research perspective," Renewable Energy, Elsevier, vol. 87(P2), pages 977-989.
    8. Zailan, Roziah & Lim, Jeng Shiun & Manan, Zainuddin Abdul & Alwi, Sharifah Rafidah Wan & Mohammadi-ivatloo, Behnam & Jamaluddin, Khairulnadzmi, 2021. "Malaysia scenario of biomass supply chain-cogeneration system and optimization modeling development: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 148(C).
    9. Devlin, Ger & Talbot, Bruce, 2014. "Deriving cooperative biomass resource transport supply strategies in meeting co-firing energy regulations: A case for peat and wood fibre in Ireland," Applied Energy, Elsevier, vol. 113(C), pages 1700-1709.
    10. Lo, Shirleen Lee Yuen & How, Bing Shen & Leong, Wei Dong & Teng, Sin Yong & Rhamdhani, Muhammad Akbar & Sunarso, Jaka, 2021. "Techno-economic analysis for biomass supply chain: A state-of-the-art review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 135(C).
    11. Shu, Kesheng & Schneider, Uwe A. & Scheffran, Jürgen, 2017. "Optimizing the bioenergy industry infrastructure: Transportation networks and bioenergy plant locations," Applied Energy, Elsevier, vol. 192(C), pages 247-261.
    12. Wegener, Moritz & Malmquist, Anders & Isalgué, Antonio & Martin, Andrew, 2018. "Biomass-fired combined cooling, heating and power for small scale applications – A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 96(C), pages 392-410.
    13. Fernández-Puratich, Harald & Rebolledo-Leiva, Ricardo & Hernández, Diógenes & Gómez-Lagos, Javier E. & Armengot-Carbo, Bruno & Oliver-Villanueva, José Vicente, 2021. "Bi-objective optimization of multiple agro-industrial wastes supply to a cogeneration system promoting local circular bioeconomy," Applied Energy, Elsevier, vol. 300(C).
    14. Mayerle, Sérgio Fernando & Neiva de Figueiredo, João, 2016. "Designing optimal supply chains for anaerobic bio-digestion/energy generation complexes with distributed small farm feedstock sourcing," Renewable Energy, Elsevier, vol. 90(C), pages 46-54.
    15. Ouhimmou, Mustapha & Rönnqvist, Mikael & Lapointe, Louis-Alexandre, 2021. "Assessment of sustainable integration of new products into value chain through a generic decision support model: An application to the forest value chain," Omega, Elsevier, vol. 99(C).
    16. Zimmer, Tobias & Rudi, Andreas & Müller, Ann-Kathrin & Fröhling, Magnus & Schultmann, Frank, 2017. "Modeling the impact of competing utilization paths on biomass-to-liquid (BtL) supply chains," Applied Energy, Elsevier, vol. 208(C), pages 954-971.
    17. Mirkouei, Amin & Haapala, Karl R. & Sessions, John & Murthy, Ganti S., 2017. "A review and future directions in techno-economic modeling and optimization of upstream forest biomass to bio-oil supply chains," Renewable and Sustainable Energy Reviews, Elsevier, vol. 67(C), pages 15-35.
    18. Leonel J. R. Nunes & Sandra Silva, 2023. "Optimization of the Residual Biomass Supply Chain: Process Characterization and Cost Analysis," Logistics, MDPI, vol. 7(3), pages 1-21, August.
    19. Sarker, Bhaba R. & Wu, Bingqing & Paudel, Krishna P., 2019. "Modeling and optimization of a supply chain of renewable biomass and biogas: Processing plant location," Applied Energy, Elsevier, vol. 239(C), pages 343-355.
    20. Mobtaker, A. & Ouhimmou, M. & Audy, J.-F. & Rönnqvist, M., 2021. "A review on decision support systems for tactical logistics planning in the context of forest bioeconomy," Renewable and Sustainable Energy Reviews, Elsevier, vol. 148(C).

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:appene:v:198:y:2017:i:c:p:160-172. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.elsevier.com/wps/find/journaldescription.cws_home/405891/description#description .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.