IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v15y2022i12p4203-d833544.html
   My bibliography  Save this article

Impact of Separator Thickness on Temperature Distribution in Single Cell of Polymer Electrolyte Fuel Cell Operated at Higher Temperature of 90 °C and 100 °C

Author

Listed:
  • Akira Nishimura

    (Division of Mechanical Engineering, Graduate School of Engineering, Mie University, 1577 Kurimamachiya-cho, Tsu 514-8507, Japan)

  • Nozomu Kono

    (Division of Mechanical Engineering, Graduate School of Engineering, Mie University, 1577 Kurimamachiya-cho, Tsu 514-8507, Japan)

  • Kyohei Toyoda

    (Division of Mechanical Engineering, Graduate School of Engineering, Mie University, 1577 Kurimamachiya-cho, Tsu 514-8507, Japan)

  • Daiki Mishima

    (Division of Mechanical Engineering, Graduate School of Engineering, Mie University, 1577 Kurimamachiya-cho, Tsu 514-8507, Japan)

  • Mohan Lal Kolhe

    (Faculty of Engineering and Science, University of Agder, P.O. Box 422, NO 4604 Kristiansand, Norway)

Abstract

The New Energy and Industry Technology Development Organization (NEDO) road map (Japan, 2017) has proposed that a polymer electrolyte fuel cell (PEFC) system, which operates at a temperature of 90 °C and 100 °C, be applied for stationary and mobility usage, respectively. This study suggests using a thin polymer electrolyte membrane (PEM) and a thin gas diffusion layer (GDL), at the same time, to achieve better power-generation performance, at a higher temperature than usual. The focus of this paper is to clarify the effect of separator thickness on the distribution of temperature at the reaction surface ( T react ), with the relative humidity (RH) of the supply gasses and initial operation temperature ( T ini ), quantitatively. In this study, separator thickness is investigated in a system using a thin PEM and a thin GDL. Moreover, this study investigates the difference between the maximum temperature and the minimum temperature obtained from the distribution of T react as well as the relation between the standard deviation of T react − T ini and total voltage, to clarify the effect of separator thickness. The impact of the flow rates of the supply gases on the distribution of T react is not large, among the investigated conditions. It is noticed that the temperature distribution is wider when a separator thickness of 2.0 mm is selected. On the other hand, it is observed that the temperature increases along with the gas flow through the gas channel, by approximately 2 °C, when using a separator thickness between 1.5 mm and 1.0 mm. The impact of the RH on the distributions of T react − T ini is larger at T ini = 100 °C, when a separator thickness of 1.0 mm is selected. It is revealed that the wider temperature distribution provides a reduction in power-generation performance. This study proposes that the thin separators, i.e., with a thickness of 1.5 mm and 1.0 mm, are not suitable for higher temperature operation than usual.

Suggested Citation

  • Akira Nishimura & Nozomu Kono & Kyohei Toyoda & Daiki Mishima & Mohan Lal Kolhe, 2022. "Impact of Separator Thickness on Temperature Distribution in Single Cell of Polymer Electrolyte Fuel Cell Operated at Higher Temperature of 90 °C and 100 °C," Energies, MDPI, vol. 15(12), pages 1-25, June.
    • Handle: RePEc:gam:jeners:v:15:y:2022:i:12:p:4203-:d:833544
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/15/12/4203/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/15/12/4203/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Xia, Lingchao & Ni, Meng & Xu, Qidong & Xu, Haoran & Zheng, Keqing, 2021. "Optimization of catalyst layer thickness for achieving high performance and low cost of high temperature proton exchange membrane fuel cell," Applied Energy, Elsevier, vol. 294(C).
    2. Nishimura, Akira & Shibuya, Kenichi & Morimoto, Atsushi & Tanaka, Shigeki & Hirota, Masafumi & Nakamura, Yoshihiro & Kojima, Masashi & Narita, Masahiko & Hu, Eric, 2012. "Dominant factor and mechanism of coupling phenomena in single cell of polymer electrolyte fuel cell," Applied Energy, Elsevier, vol. 90(1), pages 73-79.
    3. Nishimura, Akira & Yamamoto, Kohei & Okado, Tatsuya & Kojima, Yuya & Hirota, Masafumi & Kolhe, Mohan Lal, 2020. "Impact analysis of MPL and PEM thickness on temperature distribution within PEFC operating at relatively higher temperature," Energy, Elsevier, vol. 205(C).
    4. Akira Nishimura & Tatsuya Okado & Yuya Kojima & Masafumi Hirota & Eric Hu, 2020. "Impact of MPL on Temperature Distribution in Single Polymer Electrolyte Fuel Cell with Various Thicknesses of Polymer Electrolyte Membrane," Energies, MDPI, vol. 13(10), pages 1-17, May.
    5. Xia, Lingchao & Ni, Meng & He, Qijiao & Xu, Qidong & Cheng, Chun, 2021. "Optimization of gas diffusion layer in high temperature PEMFC with the focuses on thickness and porosity," Applied Energy, Elsevier, vol. 300(C).
    6. Akira Nishimura & Yuya Kojima & Syogo Ito & Eric Hu, 2022. "Impacts of Separator Thickness on Temperature Distribution and Power Generation Characteristics of a Single PEMFC Operated at Higher Temperature of 363 and 373 K," Energies, MDPI, vol. 15(4), pages 1-33, February.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Akira Nishimura & Daiki Mishima & Kyohei Toyoda & Syogo Ito & Mohan Lal Kolhe, 2023. "Numerical Simulation on Effect of Separator Thickness on Coupling Phenomena in Single Cell of PEFC under Higher Temperature Operation Condition at 363 K and 373 K," Energies, MDPI, vol. 16(2), pages 1-28, January.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Akira Nishimura & Kyohei Toyoda & Daiki Mishima & Syogo Ito & Eric Hu, 2022. "Numerical Analysis on Impact of Thickness of PEM and GDL with and without MPL on Coupling Phenomena in PEFC Operated at Higher Temperature Such as 363 K and 373 K," Energies, MDPI, vol. 15(16), pages 1-31, August.
    2. Akira Nishimura & Daiki Mishima & Kyohei Toyoda & Syogo Ito & Mohan Lal Kolhe, 2023. "Numerical Simulation on Effect of Separator Thickness on Coupling Phenomena in Single Cell of PEFC under Higher Temperature Operation Condition at 363 K and 373 K," Energies, MDPI, vol. 16(2), pages 1-28, January.
    3. Akira Nishimura & Kyohei Toyoda & Yuya Kojima & Syogo Ito & Eric Hu, 2021. "Numerical Simulation on Impacts of Thickness of Nafion Series Membranes and Relative Humidity on PEMFC Operated at 363 K and 373 K," Energies, MDPI, vol. 14(24), pages 1-24, December.
    4. Deng, Shutong & Zhang, Jun & Zhang, Caizhi & Luo, Mengzhu & Ni, Meng & Li, Yu & Zeng, Tao, 2022. "Prediction and optimization of gas distribution quality for high-temperature PEMFC based on data-driven surrogate model," Applied Energy, Elsevier, vol. 327(C).
    5. Saka, Kenan & Orhan, Mehmet Fatih, 2022. "Analysis of stack operating conditions for a polymer electrolyte membrane fuel cell," Energy, Elsevier, vol. 258(C).
    6. Bai, Fan & Quan, Hong-Bing & Yin, Ren-Jie & Zhang, Zhuo & Jin, Shu-Qi & He, Pu & Mu, Yu-Tong & Gong, Xiao-Ming & Tao, Wen-Quan, 2022. "Three-dimensional multi-field digital twin technology for proton exchange membrane fuel cells," Applied Energy, Elsevier, vol. 324(C).
    7. Teresa J. Leo & Miguel A. Raso & Emilio Navarro & Eleuterio Mora, 2013. "Long Term Performance Study of a Direct Methanol Fuel Cell Fed with Alcohol Blends," Energies, MDPI, vol. 6(1), pages 1-12, January.
    8. Wang, H.Y. & Yang, W.J. & Kim, Y.B., 2014. "Analyzing in-plane temperature distribution via a micro-temperature sensor in a unit polymer electrolyte membrane fuel cell," Applied Energy, Elsevier, vol. 124(C), pages 148-155.
    9. Zhang, Jingjing & Wang, Biao & Jin, Junhong & Yang, Shenglin & Li, Guang, 2022. "A review of the microporous layer in proton exchange membrane fuel cells: Materials and structural designs based on water transport mechanism," Renewable and Sustainable Energy Reviews, Elsevier, vol. 156(C).
    10. Xia, Sunwen & Yang, Haiping & Lu, Wang & Cai, Ning & Xiao, Haoyu & Chen, Xu & Chen, Yingquan & Wang, Xianhua & Wang, Shurong & Wu, Peng & Chen, Hanping, 2022. "Fe–Co based synergistic catalytic graphitization of biomass: Influence of the catalyst type and the pyrolytic temperature," Energy, Elsevier, vol. 239(PC).
    11. Akira Nishimura & Yuya Kojima & Syogo Ito & Eric Hu, 2022. "Impacts of Separator Thickness on Temperature Distribution and Power Generation Characteristics of a Single PEMFC Operated at Higher Temperature of 363 and 373 K," Energies, MDPI, vol. 15(4), pages 1-33, February.
    12. Xiangyang Chen & Xianglong Luo & Chao Wang & Yingzong Liang & Jianyong Chen & Zhi Yang & Jiacheng He & Ying Chen, 2024. "Channel-to-Rib Width Ratio Optimization for the Electrical Performance Enhancement in PEMFC Based on Accurate Strain-Stress Simulation," Energies, MDPI, vol. 17(3), pages 1-28, February.
    13. Wan, Yue & Qiu, Diankai & Yi, Peiyun & Peng, Linfa & Lai, Xinmin, 2022. "Design and optimization of gradient wettability pore structure of adaptive PEM fuel cell cathode catalyst layer," Applied Energy, Elsevier, vol. 312(C).
    14. Li, Li & Wang, Hongkang & Bei, Shaoyi & Li, Yuanjiang & Sun, Yanyun & Zheng, Keqing & Xu, Qiang, 2023. "Unsymmetrical design and operation in counter-flow microfluidic fuel cell: A prospective study," Energy, Elsevier, vol. 262(PB).
    15. Pei, Houchang & Xiao, Chenguang & Tu, Zhengkai, 2022. "Experimental study on liquid water formation characteristics in a novel transparent proton exchange membrane fuel cell," Applied Energy, Elsevier, vol. 321(C).
    16. Li, Bing & Wan, Kechuang & Xie, Meng & Chu, Tiankuo & Wang, Xiaolei & Li, Xiang & Yang, Daijun & Ming, Pingwen & Zhang, Cunman, 2022. "Durability degradation mechanism and consistency analysis for proton exchange membrane fuel cell stack," Applied Energy, Elsevier, vol. 314(C).
    17. Nishimura, Akira & Yamamoto, Kohei & Okado, Tatsuya & Kojima, Yuya & Hirota, Masafumi & Kolhe, Mohan Lal, 2020. "Impact analysis of MPL and PEM thickness on temperature distribution within PEFC operating at relatively higher temperature," Energy, Elsevier, vol. 205(C).
    18. Lin, Chien-Hung, 2013. "Surface roughness effect on the metallic bipolar plates of a proton exchange membrane fuel cell," Applied Energy, Elsevier, vol. 104(C), pages 898-904.
    19. Hossein Pourrahmani & Hamed Shakeri & Jan Van herle, 2022. "Thermoelectric Generator as the Waste Heat Recovery Unit of Proton Exchange Membrane Fuel Cell: A Numerical Study," Energies, MDPI, vol. 15(9), pages 1-21, April.
    20. Li, Qingshan & Wang, Chenfang & Wang, Chunmei & Zhou, Taotao & Zhang, Xianwen & Zhang, Yangjun & Zhuge, Weilin & Sun, Li, 2023. "Comparison of organic coolants for boiling cooling of proton exchange membrane fuel cell," Energy, Elsevier, vol. 266(C).

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:15:y:2022:i:12:p:4203-:d:833544. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.