IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v14y2021i22p7547-d677227.html
   My bibliography  Save this article

Combustion Characterisation of Bituminous Coal and Pinus Sawdust Blends by Use of Thermo-Gravimetric Analysis

Author

Listed:
  • Garikai T. Marangwanda

    (Department of Mechanical Engineering Science, University of Johannesburg, Johannesburg 2028, South Africa
    Department of Fuels and Energy Engineering, School of Engineering Sciences and Technologies, Chinhoyi University of Technology, Chinhoyi, Zimbabwe)

  • Daniel M. Madyira

    (Department of Mechanical Engineering Science, University of Johannesburg, Johannesburg 2028, South Africa)

  • Patrick G. Ndungu

    (Energy, Sensors and Multifunctional Nanomaterials Research Group, Department of Chemical Sciences, Doornfontein Campus, University of Johannesburg, Johannesburg 2028, South Africa)

  • Chido H. Chihobo

    (Department of Fuels and Energy Engineering, School of Engineering Sciences and Technologies, Chinhoyi University of Technology, Chinhoyi, Zimbabwe)

Abstract

The cocombustion of coal and pinus sawdust waste is an economically viable and sustainable option for increasing the share of biomass in energy production. This technology also has the potential to reduce the emission of greenhouse gases from existing coal fired power plants. The thermal synergistic effects of cocombusting Hwange bituminous coal (HC) with Pinus sawdust (PS) were thus investigated using thermogravimetric analysis. Fuel blending mass ratios of 100HC, 90HC10PS, 80HC20PS, 70HC30PS, and 100PS under an oxidative atmosphere at three different heating rates of 5, 12.5, and 20 °C/min were used for the experimental setup. Zero to negative synergy was generally observed for the mass loss curves (TG) at different blending ratios. Generally positive synergy was observed with relation to rate of mass loss curves (DTG) for the 80HC20PS and 70HC30PS fuel blends only. The ignition index increased with blending ratio by an average of 42.86%, whilst the burnout index showed a maximum increase of 14.6% at 20 °C/min. However, the combustion index representative of stability showed a decreasing trend generally for all the heating rates. No combustion index produced a linear variation with temperature, though upon evaluation, an optimum mass ratio of 20% pinus sawdust was suggested. The chosen optimum blending ratio demonstrated increased ignition and burnout indexes whilst maintaining the stability of combustion at a reasonable range.

Suggested Citation

  • Garikai T. Marangwanda & Daniel M. Madyira & Patrick G. Ndungu & Chido H. Chihobo, 2021. "Combustion Characterisation of Bituminous Coal and Pinus Sawdust Blends by Use of Thermo-Gravimetric Analysis," Energies, MDPI, vol. 14(22), pages 1-19, November.
    • Handle: RePEc:gam:jeners:v:14:y:2021:i:22:p:7547-:d:677227
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/14/22/7547/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/14/22/7547/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Savolainen, Kati, 2003. "Co-firing of biomass in coal-fired utility boilers," Applied Energy, Elsevier, vol. 74(3-4), pages 369-381, March.
    2. Tan, Peng & Ma, Lun & Xia, Ji & Fang, Qingyan & Zhang, Cheng & Chen, Gang, 2017. "Co-firing sludge in a pulverized coal-fired utility boiler: Combustion characteristics and economic impacts," Energy, Elsevier, vol. 119(C), pages 392-399.
    3. Guan-Bang Chen & Samuel Chatelier & Hsien-Tsung Lin & Fang-Hsien Wu & Ta-Hui Lin, 2018. "A Study of Sewage Sludge Co-Combustion with Australian Black Coal and Shiitake Substrate," Energies, MDPI, vol. 11(12), pages 1-25, December.
    4. Riaza, J. & Álvarez, L. & Gil, M.V. & Pevida, C. & Pis, J.J. & Rubiera, F., 2011. "Effect of oxy-fuel combustion with steam addition on coal ignition and burnout in an entrained flow reactor," Energy, Elsevier, vol. 36(8), pages 5314-5319.
    5. Wu, Zhiqiang & Zhang, Jie & Zhang, Bo & Guo, Wei & Yang, Guidong & Yang, Bolun, 2020. "Synergistic effects from co-pyrolysis of lignocellulosic biomass main component with low-rank coal: Online and offline analysis on products distribution and kinetic characteristics," Applied Energy, Elsevier, vol. 276(C).
    6. Jingura, Raphael Muzondiwa & Musademba, Downmore & Kamusoko, Reckson, 2013. "A review of the state of biomass energy technologies in Zimbabwe," Renewable and Sustainable Energy Reviews, Elsevier, vol. 26(C), pages 652-659.
    7. Lü, Hui-Fei & Deng, Jun & Li, Da-Jiang & Xu, Fan & Xiao, Yang & Shu, Chi-Min, 2021. "Effect of oxidation temperature and oxygen concentration on macro characteristics of pre-oxidised coal spontaneous combustion process," Energy, Elsevier, vol. 227(C).
    8. Joanna Wnorowska & Szymon Ciukaj & Sylwester Kalisz, 2021. "Thermogravimetric Analysis of Solid Biofuels with Additive under Air Atmosphere," Energies, MDPI, vol. 14(8), pages 1-19, April.
    9. Paniagua Bermejo, Sergio & Prado-Guerra, Alba & García Pérez, Ana Isabel & Calvo Prieto, Luis Fernando, 2020. "Study of quinoa plant residues as a way to produce energy through thermogravimetric analysis and indexes estimation," Renewable Energy, Elsevier, vol. 146(C), pages 2224-2233.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Mariusz Jerzy Stolarski & Michał Krzyżaniak & Ewelina Olba-Zięty & Jakub Stolarski, 2023. "Changes in Commercial Dendromass Properties Depending on Type and Acquisition Time," Energies, MDPI, vol. 16(24), pages 1-20, December.
    2. Dudziec, Paweł & Stachowicz, Paweł & Stolarski, Mariusz J., 2023. "Diversity of properties of sawmill residues used as feedstock for energy generation," Renewable Energy, Elsevier, vol. 202(C), pages 822-833.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Kuang, Yucen & Jiang, Tao & Wu, Longqi & Liu, Xiaoqian & Yang, Xuke & Sher, Farooq & Wei, Zhifang & Zhang, Shengfu, 2023. "High-temperature rheological behavior and non-isothermal pyrolysis mechanism of macerals separated from different coals," Energy, Elsevier, vol. 277(C).
    2. Hyukjin Oh & Kalyan Annamalai & Paul G. Goughner & Ben Thien & John M. Sweeten, 2021. "Reburning of Animal Waste Based Biomass with Coal for NO x Reduction, Part I: Feedlot Biomass (FB) and Coal:FB Blends," Energies, MDPI, vol. 14(23), pages 1-26, December.
    3. Wander, Paulo R. & Bianchi, Flávio M. & Caetano, Nattan R. & Klunk, Marcos A. & Indrusiak, Maria Luiza S., 2020. "Cofiring low-rank coal and biomass in a bubbling fluidized bed with varying excess air ratio and fluidization velocity," Energy, Elsevier, vol. 203(C).
    4. Díez, Luis I. & García-Mariaca, Alexander & Canalís, Paula & Llera, Eva, 2023. "Oxy-combustion characteristics of torrefied biomass and blends under O2/N2, O2/CO2 and O2/CO2/H2O atmospheres," Energy, Elsevier, vol. 284(C).
    5. Álvarez, L. & Gharebaghi, M. & Jones, J.M. & Pourkashanian, M. & Williams, A. & Riaza, J. & Pevida, C. & Pis, J.J. & Rubiera, F., 2013. "CFD modeling of oxy-coal combustion: Prediction of burnout, volatile and NO precursors release," Applied Energy, Elsevier, vol. 104(C), pages 653-665.
    6. Wang, Guoqiang & Wang, Feng & Li, Longjian & Zhang, Guofu, 2013. "Experiment of catalyst activity distribution effect on methanol steam reforming performance in the packed bed plate-type reactor," Energy, Elsevier, vol. 51(C), pages 267-272.
    7. Zhang, Chuan & Zhou, Li & Chhabra, Pulkit & Garud, Sushant S. & Aditya, Kevin & Romagnoli, Alessandro & Comodi, Gabriele & Dal Magro, Fabio & Meneghetti, Antonella & Kraft, Markus, 2016. "A novel methodology for the design of waste heat recovery network in eco-industrial park using techno-economic analysis and multi-objective optimization," Applied Energy, Elsevier, vol. 184(C), pages 88-102.
    8. Zhang, Zhe & Liu, Congmin & Liu, Wei & Du, Xu & Cui, Yong & Gong, Jian & Guo, Hua & Deng, Yulin, 2017. "Direct conversion of sewage sludge to electricity using polyoxomatelate catalyzed flow fuel cell," Energy, Elsevier, vol. 141(C), pages 1019-1026.
    9. Nyoni, Thabani, 2019. "Modeling and forecasting demand for electricity in Zimbabwe using the Box-Jenkins ARIMA technique," MPRA Paper 96903, University Library of Munich, Germany.
    10. Hua Wang & Wei Zhang & Haihui Xin & Deming Wang & Cuicui Di & Lu Liu, 2021. "Characteristics of Pyrolysis and Low Oxygen Combustion of Long Flame Coal and Reburning of Residues," Energies, MDPI, vol. 14(10), pages 1-17, May.
    11. Wajahat Ullah Khan Tareen & Zuha Anjum & Nabila Yasin & Leenah Siddiqui & Ifzana Farhat & Suheel Abdullah Malik & Saad Mekhilef & Mehdi Seyedmahmoudian & Ben Horan & Mohamed Darwish & Muhammad Aamir &, 2018. "The Prospective Non-Conventional Alternate and Renewable Energy Sources in Pakistan—A Focus on Biomass Energy for Power Generation, Transportation, and Industrial Fuel," Energies, MDPI, vol. 11(9), pages 1-49, September.
    12. Lizheng Zhao & Yanfei Du & Yusen Zeng & Zhizhong Kang & Baomin Sun, 2020. "Sulfur Conversion of Mixed Coal and Gangue during Combustion in a CFB Boiler," Energies, MDPI, vol. 13(3), pages 1-19, January.
    13. Rashwan, Sherif S. & Ibrahim, Abdelmaged H. & Abou-Arab, Tharwat W. & Nemitallah, Medhat A. & Habib, Mohamed A., 2017. "Experimental study of atmospheric partially premixed oxy-combustion flames anchored over a perforated plate burner," Energy, Elsevier, vol. 122(C), pages 159-167.
    14. Lasek, Janusz A. & Janusz, Marcin & Zuwała, Jarosław & Głód, Krzysztof & Iluk, Andrzej, 2013. "Oxy-fuel combustion of selected solid fuels under atmospheric and elevated pressures," Energy, Elsevier, vol. 62(C), pages 105-112.
    15. Dong, Leilei & Alexiadis, Alessio, 2023. "Simulation of char burnout characteristics of biomass/coal blend with a simplified single particle reaction model," Energy, Elsevier, vol. 264(C).
    16. Joanna Wnorowska & Szymon Ciukaj & Sylwester Kalisz, 2021. "Thermogravimetric Analysis of Solid Biofuels with Additive under Air Atmosphere," Energies, MDPI, vol. 14(8), pages 1-19, April.
    17. Xuan Liu & Yang Teng & Kai Zhang, 2022. "Migration Behaviors of As, Se and Pb in Ultra-Low-Emission Coal-Fired Units and Effect of Co-Firing Sewage Sludge in CFB Boilers," Energies, MDPI, vol. 15(4), pages 1-19, February.
    18. Yi, Baojun & Zhang, Liqi & Huang, Fang & Mao, Zhihui & Zheng, Chuguang, 2014. "Effect of H2O on the combustion characteristics of pulverized coal in O2/CO2 atmosphere," Applied Energy, Elsevier, vol. 132(C), pages 349-357.
    19. Zhu, Hongqing & Liao, Qi & Qu, Baolin & Hu, Lintao & Wang, Haoran & Gao, Rongxiang & Zhang, Yilong, 2023. "Relationship between the main functional groups and complex permittivity in pre-oxidised lignite at terahertz frequencies based on grey correlation analysis," Energy, Elsevier, vol. 278(C).
    20. Marianna Czaplicka & Justyna Klyta & Bogusław Komosiński & Tomasz Konieczny & Katarzyna Janoszka, 2021. "Comparison of Carbonaceous Compounds Emission from the Co-Combustion of Coal and Waste in Boilers Used in Residential Heating in Poland, Central Europe," Energies, MDPI, vol. 14(17), pages 1-15, August.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:14:y:2021:i:22:p:7547-:d:677227. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.