IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v11y2018i12p3483-d190369.html
   My bibliography  Save this article

Frosting Performance of a Nanoporous Hydrophilic Aluminum Surface

Author

Listed:
  • Wansheng Yang

    (School of Civil and Transportation Engineering, Guangdong University of Technology, Guangzhou 510006, China)

  • Bin Zeng

    (School of Civil and Transportation Engineering, Guangdong University of Technology, Guangzhou 510006, China)

  • Yanmei Zhang

    (School of Materials and Energy, Guangdong University of Technology, Guangzhou 510006, China)

  • Song He

    (School of Civil and Transportation Engineering, Guangdong University of Technology, Guangzhou 510006, China)

  • Xudong Zhao

    (School of Engineering, University of Hull, Hull HU6 7RX, UK)

Abstract

As an efficient energy-saving piece of equipment, an air-source heat pump can not only reduce the energy consumption required for heating, but can also reduce the pollution from fossil consumption. However, when an air-source heat pump operates under low temperatures and high humidity, the heat exchanger surface of its outdoor evaporator often get covered with frost. The growth of the frost layer seriously affects the operation efficiency of the equipment and limits its engineering application. Looking for materials that can actively inhibit frost forming is a good strategy to solve the problem mentioned above. Numerous studies show that a hydrophilic surface (contact angle less than 90°) can inhibit the normal freezing process. Manufacturing nanostructures on the surface also affect frosting performance. In this paper, nanoporous hydrophilic aluminum sheets, with contact angles of 47.8° (Sample 2), 35.9° (Sample 3), and 22.9° (Sample 4), respectively, were fabricated by the anodic oxidation method. The frosting performance of the nanoporous hydrophilic aluminum was studied compared with polished aluminum, with a contact angle of 60.2° (Sample 1). The frosting performance of the aluminum surface was systematically studied by observing the frost structure from top and side cameras and measuring the frost thickness, frost mass, and frosting rate. It was found that nanoporous hydrophilic aluminum can reduce the frost thickness and frost mass. The frost mass reduction rate of sample 2 reached a maximum of 65.9% at the surface temperature of −15 °C, under test conditions. When the surface temperature was −15 °C, the frosting rate of Sample 2 was 1.71 g/(m 2 ·min), which was about one-third of that on sample 1 (polished aluminum). Nanoporous hydrophilic aluminum behaved better at lessening frost than polished aluminum, which revealed that manufacturing nanopores and promoting hydrophilicity can delay the formation of frost.

Suggested Citation

  • Wansheng Yang & Bin Zeng & Yanmei Zhang & Song He & Xudong Zhao, 2018. "Frosting Performance of a Nanoporous Hydrophilic Aluminum Surface," Energies, MDPI, vol. 11(12), pages 1-17, December.
  • Handle: RePEc:gam:jeners:v:11:y:2018:i:12:p:3483-:d:190369
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/11/12/3483/pdf
    Download Restriction: no

    File URL: https://www.mdpi.com/1996-1073/11/12/3483/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Sheng, Wei & Liu, Pengpeng & Dang, Chaobin & Liu, Guixin, 2017. "Review of restraint frost method on cold surface," Renewable and Sustainable Energy Reviews, Elsevier, vol. 79(C), pages 806-813.
    2. Zhang, Long & Jiang, Yiqiang & Dong, Jiankai & Yao, Yang, 2018. "Advances in vapor compression air source heat pump system in cold regions: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 81(P1), pages 353-365.
    3. Yang, Liu & Yan, Haiyan & Lam, Joseph C., 2014. "Thermal comfort and building energy consumption implications – A review," Applied Energy, Elsevier, vol. 115(C), pages 164-173.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Zheng, Haikun & Ma, Chen & Fu, Dongyu & Sheng, Wei & Wang, Ruirui & Chen, Xiaozhuan & Song, Mengjie & Dang, Chaobin, 2025. "A review of defrosting methods in cold storage," Renewable and Sustainable Energy Reviews, Elsevier, vol. 214(C).
    2. Christian J. L. Hermes & Joel Boeng & Diogo L. da Silva & Fernando T. Knabben & Andrew D. Sommers, 2021. "Evaporator Frosting in Refrigerating Appliances: Fundamentals and Applications," Energies, MDPI, vol. 14(18), pages 1-23, September.
    3. Fei Wang & Rijing Zhao & Wenming Xu & Dong Huang & Zhiguo Qu, 2021. "A Heater-Assisted Air Source Heat Pump Air Conditioner to Improve Thermal Comfort with Frost-Retarded Heating and Heat-Uninterrupted Defrosting," Energies, MDPI, vol. 14(9), pages 1-13, May.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Ebrahim Morady & Madjid Soltani & Farshad Moradi Kashkooli & Masoud Ziabasharhagh & Armughan Al-Haq & Jatin Nathwani, 2022. "Improving Energy Efficiency by Utilizing Wetted Cellulose Pads in Passive Cooling Systems," Energies, MDPI, vol. 15(1), pages 1-17, January.
    2. Hinker, Jonas & Hemkendreis, Christian & Drewing, Emily & März, Steven & Hidalgo Rodríguez, Diego I. & Myrzik, Johanna M.A., 2017. "A novel conceptual model facilitating the derivation of agent-based models for analyzing socio-technical optimality gaps in the energy domain," Energy, Elsevier, vol. 137(C), pages 1219-1230.
    3. Cui, Can & Zhang, Xin & Cai, Wenjian, 2020. "An energy-saving oriented air balancing method for demand controlled ventilation systems with branch and black-box model," Applied Energy, Elsevier, vol. 264(C).
    4. Shuxue, Xu & Yueyue, Wang & Jianhui, Niu & Guoyuan, Ma, 2020. "‘Coal-to-electricity’ project is ongoing in north China," Energy, Elsevier, vol. 191(C).
    5. Picallo-Perez, Ana & Catrini, Pietro & Piacentino, Antonio & Sala, José-Mª, 2019. "A novel thermoeconomic analysis under dynamic operating conditions for space heating and cooling systems," Energy, Elsevier, vol. 180(C), pages 819-837.
    6. Małgorzata Fedorczak-Cisak & Katarzyna Nowak & Marcin Furtak, 2019. "Analysis of the Effect of Using External Venetian Blinds on the Thermal Comfort of Users of Highly Glazed Office Rooms in a Transition Season of Temperate Climate—Case Study," Energies, MDPI, vol. 13(1), pages 1-18, December.
    7. Burillo, Daniel & Chester, Mikhail V. & Pincetl, Stephanie & Fournier, Eric, 2019. "Electricity infrastructure vulnerabilities due to long-term growth and extreme heat from climate change in Los Angeles County," Energy Policy, Elsevier, vol. 128(C), pages 943-953.
    8. Shady Attia, 2020. "Spatial and Behavioral Thermal Adaptation in Net Zero Energy Buildings: An Exploratory Investigation," Sustainability, MDPI, vol. 12(19), pages 1-15, September.
    9. Li, Biao & Han, Zongwei & Bai, Chenguang & Hu, Honghao, 2019. "The influence of soil thermal properties on the operation performance on ground source heat pump system," Renewable Energy, Elsevier, vol. 141(C), pages 903-913.
    10. Bakhshoodeh, Reza & Ocampo, Carlos & Oldham, Carolyn, 2022. "Thermal performance of green façades: Review and analysis of published data," Renewable and Sustainable Energy Reviews, Elsevier, vol. 155(C).
    11. Magnouréwa Josiane Tossim & Parfait Altolnan Tombar & Sinko Banakinao & Célestin Adeito Mavunda & Tchakouni Sondou & Cyprien Coffi Aholou & Yawovi Mawuénya Xolali Dany Ayité, 2024. "Analysis of the Choice of Cement in Construction and Its Impact on Comfort in Togo," Sustainability, MDPI, vol. 16(17), pages 1-19, August.
    12. Sun, Xiaoqin & Medina, Mario A. & Lee, Kyoung Ok & Jin, Xing, 2018. "Laboratory assessment of residential building walls containing pipe-encapsulated phase change materials for thermal management," Energy, Elsevier, vol. 163(C), pages 383-391.
    13. Mohamed, Elamin & Riffat, Saffa & Omer, Siddig & Zeinelabdein, Rami, 2019. "A comprehensive investigation of using mutual air and water heating in multi-functional DX-SAMHP for moderate cold climate," Renewable Energy, Elsevier, vol. 130(C), pages 582-600.
    14. James Ogundiran & Ehsan Asadi & Manuel Gameiro da Silva, 2024. "A Systematic Review on the Use of AI for Energy Efficiency and Indoor Environmental Quality in Buildings," Sustainability, MDPI, vol. 16(9), pages 1-30, April.
    15. Yuting Qi & Queena Qian & Frits Meijer & Henk Visscher, 2020. "Causes of Quality Failures in Building Energy Renovation Projects of Northern China: A Review and Empirical Study," Energies, MDPI, vol. 13(10), pages 1-19, May.
    16. Payam Nejat & Fatemeh Jomehzadeh & Hasanen Mohammed Hussen & John Kaiser Calautit & Muhd Zaimi Abd Majid, 2018. "Application of Wind as a Renewable Energy Source for Passive Cooling through Windcatchers Integrated with Wing Walls," Energies, MDPI, vol. 11(10), pages 1-23, September.
    17. Joshua M. Pearce & Nelson Sommerfeldt, 2021. "Economics of Grid-Tied Solar Photovoltaic Systems Coupled to Heat Pumps: The Case of Northern Climates of the U.S. and Canada," Energies, MDPI, vol. 14(4), pages 1-17, February.
    18. Enescu, Diana, 2017. "A review of thermal comfort models and indicators for indoor environments," Renewable and Sustainable Energy Reviews, Elsevier, vol. 79(C), pages 1353-1379.
    19. Wang, Zhe & Hong, Tianzhen, 2020. "Learning occupants’ indoor comfort temperature through a Bayesian inference approach for office buildings in United States," Renewable and Sustainable Energy Reviews, Elsevier, vol. 119(C).
    20. Wang, Xiaotong & Lu, Meijun & Mao, Wei & Ouyang, Jinlong & Zhou, Bo & Yang, Yunkai, 2015. "Improving benefit-cost analysis to overcome financing difficulties in promoting energy-efficient renovation of existing residential buildings in China," Applied Energy, Elsevier, vol. 141(C), pages 119-130.

    More about this item

    Keywords

    ;
    ;
    ;
    ;

    Statistics

    Access and download statistics

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:11:y:2018:i:12:p:3483-:d:190369. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.