IDEAS home Printed from https://ideas.repec.org/a/eee/energy/v305y2024ics0360544224020395.html
   My bibliography  Save this article

Influence of printing parameters on the thermal properties of 3D-printed construction structures

Author

Listed:
  • Sovetova, Meruyert
  • Calautit, John Kaiser

Abstract

3D printing in the construction sector is a promising, sustainable approach with the potential to build energy-efficient buildings. However, there is a lack of studies on the thermal properties of 3D-printed structures, which are fundamental to their energy efficiency. This study investigates the impact of printing parameters on thermal conductivity and defect development in 3D-printed concrete structures. Heat flow meter, scanning electron microscope and infrared imaging techniques were employed to assess the thermal properties and microstructure of 3D-printed samples. The results demonstrate that printing parameters significantly influence the porosity, void formation, and microstructural characteristics of 3D-printed concrete, ultimately affecting thermal properties. An increase in extrusion rate leads to higher thermal conductivity, whereas an increase in speed and standoff distance reduces thermal conductivity. Excessive spacing between printed lines can induce voids and gaps, contributing to lower thermal conductivity, while minimal spacing can promote higher porosity and larger pores. Infrared imaging revealed nonuniform thermal distribution in 3D-printed structures caused by the layered structure and voids in interlayer gaps. This study provides valuable insights for designing and constructing energy-efficient 3D-printed buildings, contributing to the development of sustainable building practices and the advancement of additive manufacturing in construction.

Suggested Citation

  • Sovetova, Meruyert & Calautit, John Kaiser, 2024. "Influence of printing parameters on the thermal properties of 3D-printed construction structures," Energy, Elsevier, vol. 305(C).
    • Handle: RePEc:eee:energy:v:305:y:2024:i:c:s0360544224020395
    DOI: 10.1016/j.energy.2024.132265
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0360544224020395
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.energy.2024.132265?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Žigart, Maja & Kovačič Lukman, Rebeka & Premrov, Miroslav & Žegarac Leskovar, Vesna, 2018. "Environmental impact assessment of building envelope components for low-rise buildings," Energy, Elsevier, vol. 163(C), pages 501-512.
    2. Shabunko, Veronika & Badrinarayanan, Samyuktha & Pillai, Dhanup S., 2021. "Evaluation of in-situ thermal transmittance of innovative building integrated photovoltaic modules: Application to thermal performance assessment for green mark certification in the tropics," Energy, Elsevier, vol. 235(C).
    3. Radhi, H., 2009. "Can envelope codes reduce electricity and CO2 emissions in different types of buildings in the hot climate of Bahrain?," Energy, Elsevier, vol. 34(2), pages 205-215.
    4. Saikia, Pranaynil & Pancholi, Marmik & Sood, Divyanshu & Rakshit, Dibakar, 2020. "Dynamic optimization of multi-retrofit building envelope for enhanced energy performance with a case study in hot Indian climate," Energy, Elsevier, vol. 197(C).
    5. Markovska, Natasa & Duić, Neven & Mathiesen, Brian Vad & Guzović, Zvonimir & Piacentino, Antonio & Schlör, Holger & Lund, Henrik, 2016. "Addressing the main challenges of energy security in the twenty-first century – Contributions of the conferences on Sustainable Development of Energy, Water and Environment Systems," Energy, Elsevier, vol. 115(P3), pages 1504-1512.
    6. Bruno, Roberto & Bevilacqua, Piero, 2022. "Heat and mass transfer for the U-value assessment of opaque walls in the Mediterranean climate: Energy implications," Energy, Elsevier, vol. 261(PA).
    7. Berman, Barry, 2012. "3-D printing: The new industrial revolution," Business Horizons, Elsevier, vol. 55(2), pages 155-162.
    8. Barone, Giovanni & Buonomano, Annamaria & Giuzio, Giovanni Francesco & Palombo, Adolfo, 2023. "Towards zero energy infrastructure buildings: optimal design of envelope and cooling system," Energy, Elsevier, vol. 279(C).
    9. Darya Nemova & Evgeny Kotov & Darya Andreeva & Svyatoslav Khorobrov & Vyacheslav Olshevskiy & Irina Vasileva & Daria Zaborova & Tatiana Musorina, 2022. "Experimental Study on the Thermal Performance of 3D-Printed Enclosing Structures," Energies, MDPI, vol. 15(12), pages 1-22, June.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Nallapaneni Manoj Kumar & Aneesh A. Chand & Maria Malvoni & Kushal A. Prasad & Kabir A. Mamun & F.R. Islam & Shauhrat S. Chopra, 2020. "Distributed Energy Resources and the Application of AI, IoT, and Blockchain in Smart Grids," Energies, MDPI, vol. 13(21), pages 1-42, November.
    2. Qikang Zhong & Bo Li & Tian Dong, 2024. "Building sustainable slow communities: the impact of built environments on leisure-time physical activities in Shanghai," Palgrave Communications, Palgrave Macmillan, vol. 11(1), pages 1-21, December.
    3. Francesco Cappa & Fausto Del Sette & Darren Hayes & Federica Rosso, 2016. "How to Deliver Open Sustainable Innovation: An Integrated Approach for a Sustainable Marketable Product," Sustainability, MDPI, vol. 8(12), pages 1-14, December.
    4. Florinda Matos & Radu Godina & Celeste Jacinto & Helena Carvalho & Inês Ribeiro & Paulo Peças, 2019. "Additive Manufacturing: Exploring the Social Changes and Impacts," Sustainability, MDPI, vol. 11(14), pages 1-18, July.
    5. Yizhe Yang & Bingshan Liu & Haochen Li & Xin Li & Xiaodong Liu & Gong Wang, 2023. "Automatic selection system of the building orientation based on double-layer priority aggregation multi-attribute decision-making," Journal of Intelligent Manufacturing, Springer, vol. 34(5), pages 2477-2493, June.
    6. Yang, Sungwoong & Cho, Hyun Mi & Yun, Beom Yeol & Hong, Taehoon & Kim, Sumin, 2021. "Energy usage and cost analysis of passive thermal retrofits for low-rise residential buildings in Seoul," Renewable and Sustainable Energy Reviews, Elsevier, vol. 151(C).
    7. Na Liu & Pui-Sze Chow & Hongshan Zhao, 2020. "Challenges and critical successful factors for apparel mass customization operations: recent development and case study," Annals of Operations Research, Springer, vol. 291(1), pages 531-563, August.
    8. George Cornel Dumitrescu & Ion Alexandru Tanase, 2016. "3D Printing – A New Industrial Revolution," Knowledge Horizons - Economics, Faculty of Finance, Banking and Accountancy Bucharest,"Dimitrie Cantemir" Christian University Bucharest, vol. 8(1), pages 32-39, March.
    9. Constantinos Vassiliades & Christos Minterides & Olga-Eleni Astara & Giovanni Barone & Ioannis Vardopoulos, 2023. "Socio-Economic Barriers to Adopting Energy-Saving Bioclimatic Strategies in a Mediterranean Sustainable Real Estate Setting: A Quantitative Analysis of Resident Perspectives," Energies, MDPI, vol. 16(24), pages 1-18, December.
    10. Buonomano, A. & Forzano, C. & Mongibello, L. & Palombo, A. & Russo, G., 2024. "Optimising low-temperature district heating networks: A simulation-based approach with experimental verification," Energy, Elsevier, vol. 304(C).
    11. Lee, Junghun & Kim, Jeonggook & Song, Doosam & Kim, Jonghun & Jang, Cheolyong, 2017. "Impact of external insulation and internal thermal density upon energy consumption of buildings in a temperate climate with four distinct seasons," Renewable and Sustainable Energy Reviews, Elsevier, vol. 75(C), pages 1081-1088.
    12. Franzitta, Vincenzo & La Gennusa, Maria & Peri, Giorgia & Rizzo, Gianfranco & Scaccianoce, Gianluca, 2011. "Toward a European Eco-label brand for residential buildings: Holistic or by-components approaches?," Energy, Elsevier, vol. 36(4), pages 1884-1892.
    13. Jaya Priyadarshini & Rajesh Kr Singh & Ruchi Mishra & Surajit Bag, 2022. "Investigating the interaction of factors for implementing additive manufacturing to build an antifragile supply chain: TISM-MICMAC approach," Operations Management Research, Springer, vol. 15(1), pages 567-588, June.
    14. Ruparathna, Rajeev & Hewage, Kasun & Sadiq, Rehan, 2016. "Improving the energy efficiency of the existing building stock: A critical review of commercial and institutional buildings," Renewable and Sustainable Energy Reviews, Elsevier, vol. 53(C), pages 1032-1045.
    15. Ghobadian, Abby & Talavera, Irene & Bhattacharya, Arijit & Kumar, Vikas & Garza-Reyes, Jose Arturo & O'Regan, Nicholas, 2020. "Examining legitimatisation of additive manufacturing in the interplay between innovation, lean manufacturing and sustainability," International Journal of Production Economics, Elsevier, vol. 219(C), pages 457-468.
    16. Rong, Ke & Patton, Dean & Chen, Weiwei, 2018. "Business models dynamics and business ecosystems in the emerging 3D printing industry," Technological Forecasting and Social Change, Elsevier, vol. 134(C), pages 234-245.
    17. Guo, Shu & Choi, Tsan-Ming & Chung, Sai-Ho, 2022. "Self-design fun: Should 3D printing be employed in mass customization operations?," European Journal of Operational Research, Elsevier, vol. 299(3), pages 883-897.
    18. Calza, Elisa & Lavopa, Alejandro & Ligia Zagato, 2022. "Advanced digital technologies and industrial resilience during the COVID-19 pandemic: A firm-level perspective," MERIT Working Papers 2022-008, United Nations University - Maastricht Economic and Social Research Institute on Innovation and Technology (MERIT).
    19. Diakaki, Christina & Grigoroudis, Evangelos & Kolokotsa, Dionyssia, 2013. "Performance study of a multi-objective mathematical programming modelling approach for energy decision-making in buildings," Energy, Elsevier, vol. 59(C), pages 534-542.
    20. Tullio de Rubeis & Annamaria Ciccozzi & Letizia Giusti & Dario Ambrosini, 2022. "The 3D Printing Potential for Heat Flow Optimization: Influence of Block Geometries on Heat Transfer Processes," Sustainability, MDPI, vol. 14(23), pages 1-19, November.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:energy:v:305:y:2024:i:c:s0360544224020395. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.journals.elsevier.com/energy .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.