IDEAS home Printed from https://ideas.repec.org/a/eee/energy/v179y2019icp315-322.html
   My bibliography  Save this article

Effects of flow rate and fuel/air ratio on propagation behaviors of diffusion H2/air flames in a micro-combustor

Author

Listed:
  • Xiang, Ying
  • Yuan, Zili
  • Wang, Shixuan
  • Fan, Aiwu

Abstract

A Y-shaped micro combustor consisting of three quartz tubes with an identical inner diameter of 2.0 mm was designed. Effects of total flow rate and fuel/air ratio on the propagation behaviors of non-premixed hydrogen-air flames were investigated experimentally. Six distinct modes were observed, including flames with repetitive extinction and ignition. Noise emission was detected during flame propagation towards upstream under relatively high mixture velocities. The mean flame propagation speed decreased monotonically with an increasing mixture velocity, however, it exhibited a non-monotonic variation with the nominal equivalence ratio and peaked at ϕ = 0.9. Stable edge flames were obtained at the intersection under suitable conditions, and its length increased as the mixture velocity was increased, but varied non-monotonically with the nominal equivalence ratio and had a maximum value at ϕ = 0.9. The regime diagram of the six flame propagation modes was drawn, which can provide an overview of the relationship between the inlet condition and flame propagation mode. Qualitative analysis showed that flame dynamics of non-premixed micro-combustion was closely associated with the total flow rate and fuel/air ratio by influencing the mixing effectiveness, residence time, heat release rate and heat loss rate.

Suggested Citation

  • Xiang, Ying & Yuan, Zili & Wang, Shixuan & Fan, Aiwu, 2019. "Effects of flow rate and fuel/air ratio on propagation behaviors of diffusion H2/air flames in a micro-combustor," Energy, Elsevier, vol. 179(C), pages 315-322.
  • Handle: RePEc:eee:energy:v:179:y:2019:i:c:p:315-322
    DOI: 10.1016/j.energy.2019.05.052
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0360544219309156
    Download Restriction: Full text for ScienceDirect subscribers only

    File URL: https://libkey.io/10.1016/j.energy.2019.05.052?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Peng, Qingguo & E, Jiaqiang & Yang, W.M. & Xu, Hongpeng & Chen, Jingwei & Meng, Tian & Qiu, Runzhi, 2018. "Effects analysis on combustion and thermal performance enhancement of a nozzle-inlet micro tube fueled by the premixed hydrogen/air," Energy, Elsevier, vol. 160(C), pages 349-360.
    2. Alipoor, Alireza & Mazaheri, Kiumars, 2016. "Combustion characteristics and flame bifurcation in repetitive extinction-ignition dynamics for premixed hydrogen-air combustion in a heated micro channel," Energy, Elsevier, vol. 109(C), pages 650-663.
    3. Li, Yueh-Heng & Chen, Guan-Bang & Cheng, Tsarng-Sheng & Yeh, Yean-Ling & Chao, Yei-Chin, 2013. "Combustion characteristics of a small-scale combustor with a percolated platinum emitter tube for thermophotovoltaics," Energy, Elsevier, vol. 61(C), pages 150-157.
    4. Fan, Aiwu & Zhang, He & Wan, Jianlong, 2017. "Numerical investigation on flame blow-off limit of a novel microscale Swiss-roll combustor with a bluff-body," Energy, Elsevier, vol. 123(C), pages 252-259.
    5. Wang, Shixuan & Li, Linhong & Xia, Yongfang & Fan, Aiwu & Yao, Hong, 2018. "Effect of a catalytic segment on flame stability in a micro combustor with controlled wall temperature profile," Energy, Elsevier, vol. 165(PA), pages 522-531.
    6. Bani, Stephen & Pan, Jianfeng & Tang, Aikun & Lu, Qingbo & Zhang, Yi, 2018. "Numerical investigation of key parameters of the porous media combustion based Micro-Thermophotovoltaic system," Energy, Elsevier, vol. 157(C), pages 969-978.
    7. Alipoor, Alireza & Mazaheri, Kiumars, 2014. "Studying the repetitive extinction-ignition dynamics for lean premixed hydrogen-air combustion in a heated microchannel," Energy, Elsevier, vol. 73(C), pages 367-379.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Tang, Shihao & Wei, Jia & Xie, Bo & Shi, Zhiwei & Wang, Hao & Tian, Xinghua & He, Biao & Peng, Qingguo, 2023. "Experimental and numerical investigation on H2-fueled thermophotovoltaic micro tube with multi-cavity," Energy, Elsevier, vol. 274(C).
    2. Peng, Qingguo & Xie, Bo & Yang, Wenming & Tang, Shihao & Li, Zhenwei & Zhou, Peng & Luo, Ningkang, 2021. "Effects of porosity and multilayers of porous medium on the hydrogen-fueled combustion and micro-thermophotovoltaic," Renewable Energy, Elsevier, vol. 174(C), pages 391-402.
    3. Shilong, Zhao & Yuxin, Fan, 2020. "Experimental and numerical study on fuel distribution and flame expansion of the enhanced flame holding devices," Energy, Elsevier, vol. 203(C).
    4. Yang, Xiao & Yang, Wenming & Dong, Shikui & Tan, Heping, 2020. "Flame stability analysis of premixed hydrogen/air mixtures in a swirl micro-combustor," Energy, Elsevier, vol. 209(C).
    5. Sun, Bowen & Kang, Xin & Wang, Yu, 2020. "Numerical investigations on the methane-oxygen diffusion flame-street phenomena in a microchannel: Effects of wall temperatures, inflow rates and global equivalence ratios on flame behaviors and combu," Energy, Elsevier, vol. 207(C).
    6. Jia, Yongsheng & Wang, Yingjie & Jiang, Cong & Wang, Xun & Hu, Zhiquan & Xiao, Bo & Liu, Shiming, 2022. "Simultaneous enhancement of the H2 yield and HCl removal efficiency from pyrolysis of infusion tube under novel mayenite-based mesoporous catalytic sorbents," Energy, Elsevier, vol. 244(PB).
    7. Peng, Qingguo & Yang, Wenming & E, Jiaqiang & Li, Shaobo & Li, Zhenwei & Xu, Hongpeng & Fu, Guang, 2021. "Effects of propane addition and burner scale on the combustion characteristics and working performance," Applied Energy, Elsevier, vol. 285(C).
    8. Lopez-Ruiz, G. & Alava, I. & Urresti, I. & Blanco, J.M. & Naud, B., 2021. "Experimental and numerical study of NOx formation in a domestic H2/air coaxial burner at low Reynolds number," Energy, Elsevier, vol. 221(C).
    9. Liu, Zeqi & Liu, Wanhao & Du, Yiqing & Fan, Aiwu, 2024. "Experimental study on the propagation characteristics of non-premixed H2/air flames in a curved micro-combustor," Energy, Elsevier, vol. 299(C).
    10. Li, Linhong & Yang, Guangyao & Fan, Aiwu, 2021. "Non-premixed combustion characteristics and thermal performance of a catalytic combustor for micro-thermophotovoltaic systems," Energy, Elsevier, vol. 214(C).
    11. E, Jiaqiang & Luo, Bo & Han, Dandan & Chen, Jingwei & Liao, Gaoliang & Zhang, Feng & Ding, Jiangjun, 2022. "A comprehensive review on performance improvement of micro energy mechanical system: Heat transfer, micro combustion and energy conversion," Energy, Elsevier, vol. 239(PE).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Cai, Tao & Tang, Aikun & Zhao, Dan & Zhou, Chen & Huang, Qiuhan, 2020. "Flame dynamics and stability of premixed methane/air in micro-planar quartz combustors," Energy, Elsevier, vol. 193(C).
    2. Peng, Qingguo & Yang, Wenming & E, Jiaqiang & Li, Shaobo & Li, Zhenwei & Xu, Hongpeng & Fu, Guang, 2021. "Effects of propane addition and burner scale on the combustion characteristics and working performance," Applied Energy, Elsevier, vol. 285(C).
    3. Wan, Jianlong & Zhao, Haibo, 2018. "Thermal performance of solid walls in a mesoscale combustor with a plate flame holder and preheating channels," Energy, Elsevier, vol. 157(C), pages 448-459.
    4. Wang, Shixuan & Li, Linhong & Xia, Yongfang & Fan, Aiwu & Yao, Hong, 2018. "Effect of a catalytic segment on flame stability in a micro combustor with controlled wall temperature profile," Energy, Elsevier, vol. 165(PA), pages 522-531.
    5. E, Jiaqiang & Luo, Bo & Han, Dandan & Chen, Jingwei & Liao, Gaoliang & Zhang, Feng & Ding, Jiangjun, 2022. "A comprehensive review on performance improvement of micro energy mechanical system: Heat transfer, micro combustion and energy conversion," Energy, Elsevier, vol. 239(PE).
    6. Ni, Siliang & Zhao, Dan & Sellier, Mathieu & Li, Junwei & Chen, Xinjian & Li, Xinyan & Cao, Feng & Li, Weixuan, 2021. "Thermal performances and emitter efficiency improvement studies on premixed micro-combustors with different geometric shapes for thermophotovoltaics applications," Energy, Elsevier, vol. 226(C).
    7. Sun, Bowen & Kang, Xin & Wang, Yu, 2020. "Numerical investigations on the methane-oxygen diffusion flame-street phenomena in a microchannel: Effects of wall temperatures, inflow rates and global equivalence ratios on flame behaviors and combu," Energy, Elsevier, vol. 207(C).
    8. Wan, Jianlong & Zhao, Haibo, 2020. "Effect of conjugate heat exchange of flame holder on laminar premixed flame stabilization in a meso-scale diverging combustor," Energy, Elsevier, vol. 198(C).
    9. Tang, Aikun & Cai, Tao & Deng, Jiang & Zhao, Dan & Huang, Qiuhan & Zhou, Chen, 2019. "Experimental study on flame structure transitions of premixed propane/air in micro-scale planar combustors," Energy, Elsevier, vol. 179(C), pages 558-570.
    10. Huang, Yakun & He, Xiaomin & Jin, Yi & Zhu, Huanyu & Zhu, Zhixin, 2021. "Effect of non-uniform inlet profile on the combustion performance of an afterburner with bluff body," Energy, Elsevier, vol. 216(C).
    11. Wan, Jianlong & Fan, Aiwu & Yao, Hong & Liu, Wei, 2016. "Experimental investigation and numerical analysis on the blow-off limits of premixed CH4/air flames in a mesoscale bluff-body combustor," Energy, Elsevier, vol. 113(C), pages 193-203.
    12. Peng, Qingguo & Wu, Yifeng & E, Jiaqiang & Yang, Wenming & Xu, Hongpeng & Li, Zhenwei, 2019. "Combustion characteristics and thermal performance of premixed hydrogen-air in a two-rearward-step micro tube," Applied Energy, Elsevier, vol. 242(C), pages 424-438.
    13. E, Jiaqiang & Meng, Tian & Chen, Jingwei & Wu, Weiwei & Zhao, Xiaohuan & Zhang, Bin & Peng, Qingguo, 2021. "Effect analysis on performance enhancement of a hydrogen/air non-premixed micro combustor with sudden expansion and contraction structure," Energy, Elsevier, vol. 230(C).
    14. Yang, Xiao & Yang, Wenming & Dong, Shikui & Tan, Heping, 2020. "Flame stability analysis of premixed hydrogen/air mixtures in a swirl micro-combustor," Energy, Elsevier, vol. 209(C).
    15. Zhuang Kang & Zhiwei Shi & Jiahao Ye & Xinghua Tian & Zhixin Huang & Hao Wang & Depeng Wei & Qingguo Peng & Yaojie Tu, 2023. "A Review of Micro Power System and Micro Combustion: Present Situation, Techniques and Prospects," Energies, MDPI, vol. 16(7), pages 1-28, April.
    16. Zuo, Wei & E, Jiaqiang & Hu, Wenyu & Jin, Yu & Han, Dandan, 2017. "Numerical investigations on combustion characteristics of H2/air premixed combustion in a micro elliptical tube combustor," Energy, Elsevier, vol. 126(C), pages 1-12.
    17. Fan, Aiwu & Zhang, He & Wan, Jianlong, 2017. "Numerical investigation on flame blow-off limit of a novel microscale Swiss-roll combustor with a bluff-body," Energy, Elsevier, vol. 123(C), pages 252-259.
    18. Alipoor, Alireza & Saidi, Mohammad Hassan, 2017. "Numerical study of hydrogen-air combustion characteristics in a novel micro-thermophotovoltaic power generator," Applied Energy, Elsevier, vol. 199(C), pages 382-399.
    19. He, Ziqiang & Yan, Yunfei & Zhao, Ting & Zhang, Zhien & Mikulčić, Hrvoje, 2022. "Parametric study of inserting internal spiral fins on the micro combustor performance for thermophotovoltaic systems," Renewable and Sustainable Energy Reviews, Elsevier, vol. 165(C).
    20. Yang, Xiao & He, Zhihong & Cha, Suna & Zhao, Lei & Dong, Shikui & Tan, Heping, 2020. "Parametric analysis on the combustion and thermal performance of a swirl micro-combustor for micro thermophotovoltaic system," Energy, Elsevier, vol. 198(C).

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:energy:v:179:y:2019:i:c:p:315-322. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.journals.elsevier.com/energy .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.