IDEAS home Printed from https://ideas.repec.org/a/eee/appene/v279y2020ics0306261920313532.html
   My bibliography  Save this article

Reforming of diesel and jet fuel for fuel cells on a systems level: Steady-state and transient operation

Author

Listed:
  • Samsun, Remzi Can
  • Prawitz, Matthias
  • Tschauder, Andreas
  • Meißner, Jan
  • Pasel, Joachim
  • Peters, Ralf

Abstract

The operation of fuel cell systems using liquid fuels widens the application possibilities of this promising energy conversion technology. However, systems utilizing diesel and jet fuel reforming are fairly complex and suffer from poor stability and limited dynamics. To address these challenges, this paper investigates the steady-state and transient operation of a 28 kWth fuel processor on the systems level. With the help of experiments that make use of the developed prototype, suitable operating parameters are sought to maximize the simultaneous fuel conversion in the reformer and CO conversion in the shift reactor. Furthermore, a load change strategy is developed with the aim of keeping the CO concentration at the fuel cell anode inlet below the target concentration of 1% of the wet product gas at all times. The identified parameters enable very high conversions (>99.95%) and CO concentrations even lower than the target during steady-state operation using three commercial fuels under full load. The developed load change strategy was validated during 90 min tests, including 16 load change cycles with loads between 40% and 100%. As well as providing excess steam during load change, the selection and control of optimal O2/C and H2O/C ratios and temperature levels proved to be of key importance. In order to minimize the CO concentration, it is recommended to operate the reformer at the identified parameters for each fuel and keep the shift outlet temperature between 295 and 300 °C by adjusting the water feed. The proposed fuel processor concept and the experimentally-validated operating strategies in this work can enable the successful implementation of fuel cell technology in different application areas, including auxiliary power units, remote power systems and range extenders.

Suggested Citation

  • Samsun, Remzi Can & Prawitz, Matthias & Tschauder, Andreas & Meißner, Jan & Pasel, Joachim & Peters, Ralf, 2020. "Reforming of diesel and jet fuel for fuel cells on a systems level: Steady-state and transient operation," Applied Energy, Elsevier, vol. 279(C).
    • Handle: RePEc:eee:appene:v:279:y:2020:i:c:s0306261920313532
    DOI: 10.1016/j.apenergy.2020.115882
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0306261920313532
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.apenergy.2020.115882?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. D.F. Chuahy, Flavio & Kokjohn, Sage L., 2017. "High efficiency dual-fuel combustion through thermochemical recovery and diesel reforming," Applied Energy, Elsevier, vol. 195(C), pages 503-522.
    2. Walluk, Mark R. & Lin, Jiefeng & Waller, Michael G. & Smith, Daniel F. & Trabold, Thomas A., 2014. "Diesel auto-thermal reforming for solid oxide fuel cell systems: Anode off-gas recycle simulation," Applied Energy, Elsevier, vol. 130(C), pages 94-102.
    3. Hanyu Chen & Xi Wang & Zhixiang Pan & Hongming Xu, 2019. "Numerical Simulation and Experimental Investigation of Diesel Fuel Reforming over a Pt/CeO 2 -Al 2 O 3 Catalyst," Energies, MDPI, vol. 12(6), pages 1-14, March.
    4. Pasel, Joachim & Samsun, Remzi Can & Tschauder, Andreas & Peters, Ralf & Stolten, Detlef, 2017. "Advances in autothermal reformer design," Applied Energy, Elsevier, vol. 198(C), pages 88-98.
    5. Peters, R. & Samsun, R.C., 2013. "Evaluation of multifunctional fuel cell systems in aviation using a multistep process analysis methodology," Applied Energy, Elsevier, vol. 111(C), pages 46-63.
    6. Wierzbicki, Teresa A. & Lee, Ivan C. & Gupta, Ashwani K., 2016. "Recent advances in catalytic oxidation and reformation of jet fuels," Applied Energy, Elsevier, vol. 165(C), pages 904-918.
    7. Samsun, Remzi Can & Pasel, Joachim & Janßen, Holger & Lehnert, Werner & Peters, Ralf & Stolten, Detlef, 2014. "Design and test of a 5kWe high-temperature polymer electrolyte fuel cell system operated with diesel and kerosene," Applied Energy, Elsevier, vol. 114(C), pages 238-249.
    8. Bizon, Nicu, 2019. "Real-time optimization strategies of Fuel Cell Hybrid Power Systems based on Load-following control: A new strategy, and a comparative study of topologies and fuel economy obtained," Applied Energy, Elsevier, vol. 241(C), pages 444-460.
    9. Krekel, Daniel & Samsun, Remzi Can & Pasel, Joachim & Prawitz, Matthias & Peters, Ralf & Stolten, Detlef, 2016. "Operating strategies for fuel processing systems with a focus on water–gas shift reactor stability," Applied Energy, Elsevier, vol. 164(C), pages 540-552.
    10. Samsun, Remzi Can & Prawitz, Matthias & Tschauder, Andreas & Pasel, Joachim & Pfeifer, Peter & Peters, Ralf & Stolten, Detlef, 2018. "An integrated diesel fuel processing system with thermal start-up for fuel cells," Applied Energy, Elsevier, vol. 226(C), pages 145-159.
    11. Xu, Xinhai & Li, Peiwen & Shen, Yuesong, 2013. "Small-scale reforming of diesel and jet fuels to make hydrogen and syngas for fuel cells: A review," Applied Energy, Elsevier, vol. 108(C), pages 202-217.
    12. Tribioli, Laura & Cozzolino, Raffaello & Chiappini, Daniele & Iora, Paolo, 2016. "Energy management of a plug-in fuel cell/battery hybrid vehicle with on-board fuel processing," Applied Energy, Elsevier, vol. 184(C), pages 140-154.
    13. Martinez, Andrew S. & Brouwer, Jacob & Samuelsen, G. Scott, 2015. "Comparative analysis of SOFC–GT freight locomotive fueled by natural gas and diesel with onboard reformation," Applied Energy, Elsevier, vol. 148(C), pages 421-438.
    14. Pregelj, Boštjan & Micor, Michał & Dolanc, Gregor & Petrovčič, Janko & Jovan, Vladimir, 2016. "Impact of fuel cell and battery size to overall system performance – A diesel fuel-cell APU case study," Applied Energy, Elsevier, vol. 182(C), pages 365-375.
    15. Ercolino, Giuliana & Ashraf, Muhammad A. & Specchia, Vito & Specchia, Stefania, 2015. "Performance evaluation and comparison of fuel processors integrated with PEM fuel cell based on steam or autothermal reforming and on CO preferential oxidation or selective methanation," Applied Energy, Elsevier, vol. 143(C), pages 138-153.
    16. Han, Gwangwoo & Lee, Sangho & Bae, Joongmyeon, 2015. "Diesel autothermal reforming with hydrogen peroxide for low-oxygen environments," Applied Energy, Elsevier, vol. 156(C), pages 99-106.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Remzi Can Samsun & Matthias Prawitz & Andreas Tschauder & Stefan Weiske & Joachim Pasel & Ralf Peters, 2021. "A Compact, Self-Sustaining Fuel Cell Auxiliary Power Unit Operated on Diesel Fuel," Energies, MDPI, vol. 14(18), pages 1-28, September.
    2. Pan, Zehua & Shen, Jian & Wang, Jingyi & Xu, Xinhai & Chan, Wei Ping & Liu, Siyu & Zhou, Yexin & Yan, Zilin & Jiao, Zhenjun & Lim, Teik-Thye & Zhong, Zheng, 2022. "Thermodynamic analyses of a standalone diesel-fueled distributed power generation system based on solid oxide fuel cells," Applied Energy, Elsevier, vol. 308(C).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Samsun, Remzi Can & Prawitz, Matthias & Tschauder, Andreas & Pasel, Joachim & Pfeifer, Peter & Peters, Ralf & Stolten, Detlef, 2018. "An integrated diesel fuel processing system with thermal start-up for fuel cells," Applied Energy, Elsevier, vol. 226(C), pages 145-159.
    2. Pasel, Joachim & Samsun, Remzi Can & Tschauder, Andreas & Peters, Ralf & Stolten, Detlef, 2017. "Advances in autothermal reformer design," Applied Energy, Elsevier, vol. 198(C), pages 88-98.
    3. Pregelj, Boštjan & Micor, Michał & Dolanc, Gregor & Petrovčič, Janko & Jovan, Vladimir, 2016. "Impact of fuel cell and battery size to overall system performance – A diesel fuel-cell APU case study," Applied Energy, Elsevier, vol. 182(C), pages 365-375.
    4. Purnima, P. & Jayanti, S., 2017. "Water neutrality and waste heat management in ethanol reformer - HTPEMFC integrated system for on-board hydrogen generation," Applied Energy, Elsevier, vol. 199(C), pages 169-179.
    5. Han, Gwangwoo & Lee, Sangho & Bae, Joongmyeon, 2015. "Diesel autothermal reforming with hydrogen peroxide for low-oxygen environments," Applied Energy, Elsevier, vol. 156(C), pages 99-106.
    6. Tribioli, Laura & Cozzolino, Raffaello & Chiappini, Daniele & Iora, Paolo, 2016. "Energy management of a plug-in fuel cell/battery hybrid vehicle with on-board fuel processing," Applied Energy, Elsevier, vol. 184(C), pages 140-154.
    7. Laura Tribioli & Raffaello Cozzolino & Daniele Chiappini, 2017. "Technical Assessment of Different Operating Conditions of an On-Board Autothermal Reformer for Fuel Cell Vehicles," Energies, MDPI, vol. 10(7), pages 1-17, June.
    8. Yao He & Changchang Miao & Ji Wu & Xinxin Zheng & Xintian Liu & Xingtao Liu & Feng Han, 2021. "Research on the Power Distribution Method for Hybrid Power System in the Fuel Cell Vehicle," Energies, MDPI, vol. 14(3), pages 1-15, January.
    9. Wang, Yujie & Sun, Zhendong & Chen, Zonghai, 2019. "Energy management strategy for battery/supercapacitor/fuel cell hybrid source vehicles based on finite state machine," Applied Energy, Elsevier, vol. 254(C).
    10. Alessandro Serpi & Mario Porru, 2019. "Modelling and Design of Real-Time Energy Management Systems for Fuel Cell/Battery Electric Vehicles," Energies, MDPI, vol. 12(22), pages 1-21, November.
    11. Pasel, Joachim & Samsun, Remzi Can & Tschauder, Andreas & Peters, Ralf & Stolten, Detlef, 2015. "A novel reactor type for autothermal reforming of diesel fuel and kerosene," Applied Energy, Elsevier, vol. 150(C), pages 176-184.
    12. Sun, Zhendong & Wang, Yujie & Chen, Zonghai & Li, Xiyun, 2020. "Min-max game based energy management strategy for fuel cell/supercapacitor hybrid electric vehicles," Applied Energy, Elsevier, vol. 267(C).
    13. Abdin, Zainul & Zafaranloo, Ali & Rafiee, Ahmad & Mérida, Walter & Lipiński, Wojciech & Khalilpour, Kaveh R., 2020. "Hydrogen as an energy vector," Renewable and Sustainable Energy Reviews, Elsevier, vol. 120(C).
    14. Fiore, M. & Magi, V. & Viggiano, A., 2020. "Internal combustion engines powered by syngas: A review," Applied Energy, Elsevier, vol. 276(C).
    15. Peng, Fei & Zhao, Yuanzhe & Li, Xiaopeng & Liu, Zhixiang & Chen, Weirong & Liu, Yang & Zhou, Donghua, 2017. "Development of master-slave energy management strategy based on fuzzy logic hysteresis state machine and differential power processing compensation for a PEMFC-LIB-SC hybrid tramway," Applied Energy, Elsevier, vol. 206(C), pages 346-363.
    16. Samsun, Remzi Can & Pasel, Joachim & Janßen, Holger & Lehnert, Werner & Peters, Ralf & Stolten, Detlef, 2014. "Design and test of a 5kWe high-temperature polymer electrolyte fuel cell system operated with diesel and kerosene," Applied Energy, Elsevier, vol. 114(C), pages 238-249.
    17. Bizon, Nicu, 2019. "Efficient fuel economy strategies for the Fuel Cell Hybrid Power Systems under variable renewable/load power profile," Applied Energy, Elsevier, vol. 251(C), pages 1-1.
    18. Walluk, Mark R. & Lin, Jiefeng & Waller, Michael G. & Smith, Daniel F. & Trabold, Thomas A., 2014. "Diesel auto-thermal reforming for solid oxide fuel cell systems: Anode off-gas recycle simulation," Applied Energy, Elsevier, vol. 130(C), pages 94-102.
    19. Kurnia, Jundika C. & Sasmito, Agus P. & Shamim, Tariq, 2017. "Performance evaluation of a PEM fuel cell stack with variable inlet flows under simulated driving cycle conditions," Applied Energy, Elsevier, vol. 206(C), pages 751-764.
    20. Kinnon, Michael Mac & Razeghi, Ghazal & Samuelsen, Scott, 2021. "The role of fuel cells in port microgrids to support sustainable goods movement," Renewable and Sustainable Energy Reviews, Elsevier, vol. 147(C).

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:appene:v:279:y:2020:i:c:s0306261920313532. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.elsevier.com/wps/find/journaldescription.cws_home/405891/description#description .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.