IDEAS home Printed from https://ideas.repec.org/a/sae/risrel/v230y2016i2p178-194.html
   My bibliography  Save this article

Fault diagnosis for the complex manufacturing system

Author

Listed:
  • Dang Trinh Nguyen
  • Quoc Bao Duong
  • Eric Zamai
  • Muhammad Kashif Shahzad

Abstract

Present manufacturing systems are equipped with sensors that provide a basis for real-time monitoring and diagnosis; however, placement of these sensors is constrained by the the functions that they perform and the system’s structure. Moreover, sensors cannot be placed across all components in the equipment due to significant data challenges. This results in non-observable components, which limit our ability to support effective real-time monitoring and fault diagnosis initiatives. Consequently, product quality drifts found during inspection often result in unscheduled breakdown of all equipment involved in respective production operation. This situation becomes more complex for automated manufacturing lines, where success depends on our ability to capitalize maximum production capacities. This paper proposes a methodology that exploits historical data over unobserved equipment components to reduce the search space of potential faulty components, followed by a more accurate diagnosis of failures and causes. The purpose is to improve the effectiveness and efficiency of both the real-time monitoring of potential faulty components and the diagnosis of causes. In the proposed approach, we use a logical diagnosis approach to reduce the search space of suspected equipment in the production flow, which is then formulated as a Bayesian network. The proposed approach computes the risk priority for suspected equipment with corresponding factors (such as human factor and recipe), using joint and conditional probabilities. The objective is to quickly and accurately localize the possible fault origins in real-time and support effective corrective maintenance decisions. The key advantages offered by this approach are: (i) reduced unscheduled equipment breakdown duration, and (ii) stable production capacities, required for success in highly competitive and automated manufacturing systems. Moreover, this is a generic methodology and can be deployed on fully or semi-automated manufacturing systems.

Suggested Citation

  • Dang Trinh Nguyen & Quoc Bao Duong & Eric Zamai & Muhammad Kashif Shahzad, 2016. "Fault diagnosis for the complex manufacturing system," Journal of Risk and Reliability, , vol. 230(2), pages 178-194, April.
    • Handle: RePEc:sae:risrel:v:230:y:2016:i:2:p:178-194
    DOI: 10.1177/1748006X15623089
    as

    Download full text from publisher

    File URL: https://journals.sagepub.com/doi/10.1177/1748006X15623089
    Download Restriction: no
    File URL: https://libkey.io/10.1177/1748006X15623089?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    References listed on IDEAS

    as
    1. Chrissoleon T. Papadopoulos & Michael J. Vidalis & Michael E. J. O’Kelly & Diomidis Spinellis, 2009. "The Design of Production Lines," Springer Optimization and Its Applications, in: Analysis and Design of Discrete Part Production Lines, chapter 3, pages 101-111, Springer.
    2. Diomidis Spinellis & Michael J. Vidalis & Michael E. J. O'Kelly & Chrissoleon T. Papadopoulos, 2009. "Analysis and Design of Discrete Part Production Lines," Springer Optimization and Its Applications, Springer, number 978-0-387-89494-2, September.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. SICARD, Franck & ZAMAI, Éric & FLAUS, Jean-Marie, 2019. "An approach based on behavioral models and critical states distance notion for improving cybersecurity of industrial control systems," Reliability Engineering and System Safety, Elsevier, vol. 188(C), pages 584-603.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Huynh, Linh & Hoang, Hien & Tran, Hung, 2020. "Does FDI enhance provincial productivity? A panel data analysis in Vietnam," MPRA Paper 117620, University Library of Munich, Germany, revised Aug 2021.
    2. Ziwei Lin & Nicla Frigerio & Andrea Matta & Shichang Du, 2021. "Multi-fidelity surrogate-based optimization for decomposed buffer allocation problems," OR Spectrum: Quantitative Approaches in Management, Springer;Gesellschaft für Operations Research e.V., vol. 43(1), pages 223-253, March.
    3. Rodríguez-Castelán, Carlos & López-Calva, Luis Felipe & Barriga-Cabanillas, Oscar, 2023. "Market concentration, trade exposure, and firm productivity in developing countries: Evidence from Mexico," World Development, Elsevier, vol. 165(C).
    4. Konstantinos S. Boulas & Georgios D. Dounias & Chrissoleon T. Papadopoulos, 2023. "A hybrid evolutionary algorithm approach for estimating the throughput of short reliable approximately balanced production lines," Journal of Intelligent Manufacturing, Springer, vol. 34(2), pages 823-852, February.
    5. Lei Li & YanLing Qian & Yong Min Yang & Kai Du, 2016. "A fast algorithm for buffer allocation problem," International Journal of Production Research, Taylor & Francis Journals, vol. 54(11), pages 3243-3255, June.
    6. Andrea Matta & Francesca Simone, 2016. "Analysis of two-machine lines with finite buffer, operation-dependent and time-dependent failure modes," International Journal of Production Research, Taylor & Francis Journals, vol. 54(6), pages 1850-1862, March.
    7. Lei Li & YanLing Qian & Kai Du & YongMin Yang, 2016. "Analysis of approximately balanced production lines," International Journal of Production Research, Taylor & Francis Journals, vol. 54(3), pages 647-664, February.
    8. Mohammad Reza Bazargan-Lari & Sharareh Taghipour & Arash Zaretalab & Mani Sharifi, 2022. "Production scheduling optimization for parallel machines subject to physical distancing due to COVID-19 pandemic," Operations Management Research, Springer, vol. 15(1), pages 503-527, June.
    9. Sachs, F.E. & Helber, S. & Kiesmüller, G.P., 2022. "Evaluation of Unreliable Flow Lines with Limited Buffer Capacities and Spare Part Provisioning," European Journal of Operational Research, Elsevier, vol. 302(2), pages 544-559.
    10. Angelos Kourepis & Alexandros Diamantidis & Stylianos Koukoumialos, 2022. "Exact analysis of a push–pull system with multiple non identical retailers, a distribution center and multiple non identical unreliable suppliers with supply disruptions," Operational Research, Springer, vol. 22(5), pages 4801-4827, November.
    11. James MacGregor Smith, 2018. "Simultaneous buffer and service rate allocation in open finite queueing networks," IISE Transactions, Taylor & Francis Journals, vol. 50(3), pages 203-216, March.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:sae:risrel:v:230:y:2016:i:2:p:178-194. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: SAGE Publications (email available below). General contact details of provider: .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.