IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v15y2021i1p179-d712800.html
   My bibliography  Save this article

Numerical Analysis on Thermohydraulic Performance of the Tube Inserted with Rectangular Winglet Vortex Generators

Author

Listed:
  • Yicong Li

    (School of Naval Architecture, Ocean and Energy Power Engineering, Wuhan University of Technology, Wuhan 430063, China)

  • Zuoqin Qian

    (School of Naval Architecture, Ocean and Energy Power Engineering, Wuhan University of Technology, Wuhan 430063, China)

  • Qiang Wang

    (School of Naval Architecture, Ocean and Energy Power Engineering, Wuhan University of Technology, Wuhan 430063, China)

Abstract

The aim of this design was to improve the heat transfer performance significantly due to larger turbulent region and much vortices formed by tube inserted. In this article, the BSL k-ω model was chosen as turbulence model to simulate the thermohydraulic performance of the proposed tubes inserted with rectangular winglet vortex generators (RWVGs) when the Re was set as 5000 to 15,000. The reliability of the simulation results was obtained by comparing with the empirical formulas and experimental results. By means of numerical simulation, the influence mechanism of geometric parameters of RWVGs on thermal-hydraulic performance in tubes was analyzed. And the impact of three configurational parameters on the thermal performance was studied, namely the angle α , the height H and the number N of the RWVGs, respectively. The results revealed that the capacity of heat transfer in tubes with RWVG inserts was obviously larger than that in ordinary circular tube. In addition, it could be seen from the results that both Nu and f increased with the increase of H and N . At the same time, the case of α = 135° showed the greatest enhancement of thermal performance than the case of α = 45° and α = 90°.The PEC achieved the highest value of 1.23 when the height H of RWVG was 0.7 mm, the number N was 20, and angle α was 135°.

Suggested Citation

  • Yicong Li & Zuoqin Qian & Qiang Wang, 2021. "Numerical Analysis on Thermohydraulic Performance of the Tube Inserted with Rectangular Winglet Vortex Generators," Energies, MDPI, vol. 15(1), pages 1-23, December.
    • Handle: RePEc:gam:jeners:v:15:y:2021:i:1:p:179-:d:712800
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/15/1/179/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/15/1/179/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Liu, S. & Sakr, M., 2013. "A comprehensive review on passive heat transfer enhancements in pipe exchangers," Renewable and Sustainable Energy Reviews, Elsevier, vol. 19(C), pages 64-81.
    2. Sheikholeslami, Mohsen & Gorji-Bandpy, Mofid & Ganji, Davood Domiri, 2015. "Review of heat transfer enhancement methods: Focus on passive methods using swirl flow devices," Renewable and Sustainable Energy Reviews, Elsevier, vol. 49(C), pages 444-469.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Rashidi, Saman & Hormozi, Faramarz & Sundén, Bengt & Mahian, Omid, 2019. "Energy saving in thermal energy systems using dimpled surface technology – A review on mechanisms and applications," Applied Energy, Elsevier, vol. 250(C), pages 1491-1547.
    2. Sun, Yalong & Tang, Yong & Zhang, Shiwei & Yuan, Wei & Tang, Heng, 2022. "A review on fabrication and pool boiling enhancement of three-dimensional complex structures," Renewable and Sustainable Energy Reviews, Elsevier, vol. 162(C).
    3. Gallegos, Ralph Kristoffer B. & Sharma, Rajnish N., 2017. "Flags as vortex generators for heat transfer enhancement: Gaps and challenges," Renewable and Sustainable Energy Reviews, Elsevier, vol. 76(C), pages 950-962.
    4. Yicong Li & Zuoqin Qian & Qiang Wang, 2022. "A Thermohydraulic Performance of Internal Spiral Finned Tube Based on the Inner Tube Secondary Flow," Energies, MDPI, vol. 15(2), pages 1-23, January.
    5. Hui Xiao & Zhimin Dong & Rui Long & Kun Yang & Fang Yuan, 2019. "A Study on the Mechanism of Convective Heat Transfer Enhancement Based on Heat Convection Velocity Analysis," Energies, MDPI, vol. 12(21), pages 1-22, November.
    6. Singla, Mohit & Hans, Vishavjeet Singh & Singh, Sukhmeet, 2022. "CFD analysis of rib roughened solar evacuated tube collector for air heating," Renewable Energy, Elsevier, vol. 183(C), pages 78-89.
    7. Sheikholeslami, M. & Ganji, D.D., 2016. "Heat transfer enhancement in an air to water heat exchanger with discontinuous helical turbulators; experimental and numerical studies," Energy, Elsevier, vol. 116(P1), pages 341-352.
    8. Acherjee, Simul & Deb, Ujjwal Kumar & Bhuyan, Md. Moniruzzaman, 2020. "The effect of the angle of perforation on perforated inserts in a pipe flow for heat transfer analysis," Mathematics and Computers in Simulation (MATCOM), Elsevier, vol. 171(C), pages 306-314.
    9. Chang, Chun & Sciacovelli, Adriano & Wu, Zhiyong & Li, Xin & Li, Yongliang & Zhao, Mingzhi & Deng, Jie & Wang, Zhifeng & Ding, Yulong, 2018. "Enhanced heat transfer in a parabolic trough solar receiver by inserting rods and using molten salt as heat transfer fluid," Applied Energy, Elsevier, vol. 220(C), pages 337-350.
    10. Yazid, Muhammad Noor Afiq Witri Muhammad & Sidik, Nor Azwadi Che & Yahya, Wira Jazair, 2017. "Heat and mass transfer characteristics of carbon nanotube nanofluids: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 80(C), pages 914-941.
    11. Cao, Yan & Ayed, Hamdi & Hashemian, Mehran & Issakhov, Alibek & Jarad, Fahd & Wae-hayee, Makatar, 2021. "Inducing swirl flow inside the pipes of flat-plate solar collector by using multiple nozzles for enhancing thermal performance," Renewable Energy, Elsevier, vol. 180(C), pages 1344-1357.
    12. Manikandan, G.K. & Iniyan, S. & Goic, Ranko, 2019. "Enhancing the optical and thermal efficiency of a parabolic trough collector – A review," Applied Energy, Elsevier, vol. 235(C), pages 1524-1540.
    13. Vanaki, Sh.M. & Ganesan, P. & Mohammed, H.A., 2016. "Numerical study of convective heat transfer of nanofluids: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 54(C), pages 1212-1239.
    14. Arnut Phila & Chinaruk Thianpong & Smith Eiamsa-ard, 2019. "Influence of Geometric Parameters of Alternate Axis Twisted Baffles on the Local Heat Transfer Distribution and Pressure Drop in a Rectangular Channel Using a Transient Liquid Crystal Technique," Energies, MDPI, vol. 12(12), pages 1-25, June.
    15. Zhang, Shiyou & Peng, Keming & Wei, Wenlong & Tang, Siqi & Yao, Jin, 2021. "The matrix method of energy analysis and energy-saving design on the electromechanical system," Energy, Elsevier, vol. 224(C).
    16. Gürdal, Mehmet & Arslan, Kamil & Gedik, Engin & Minea, Alina Adriana, 2022. "Effects of using nanofluid, applying a magnetic field, and placing turbulators in channels on the convective heat transfer: A comprehensive review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 162(C).
    17. Ahadi, Mohammad & Abbassi, Abbas, 2015. "Entropy generation analysis of laminar forced convection through uniformly heated helical coils considering effects of high length and heat flux and temperature dependence of thermophysical properties," Energy, Elsevier, vol. 82(C), pages 322-332.
    18. Jafari, Davoud & Wits, Wessel W., 2018. "The utilization of selective laser melting technology on heat transfer devices for thermal energy conversion applications: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 91(C), pages 420-442.
    19. Kumar, Rajneesh & Varun, & Kumar, Anoop, 2016. "Thermal and fluid dynamic characteristics of flow through triangular cross-sectional duct: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 61(C), pages 123-140.
    20. Feng, Zhenfei & Jiang, Ping & Zheng, Siyao & Zhang, Qingyuan & Chen, Zhen & Guo, Fangwen & Zhang, Jinxin, 2023. "Experimental and numerical investigations on the effects of insertion-type longitudinal vortex generators on flow and heat transfer characteristics in square minichannels," Energy, Elsevier, vol. 278(PA).

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:15:y:2021:i:1:p:179-:d:712800. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.