IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v13y2020i23p6163-d450162.html
   My bibliography  Save this article

Thermodynamic Modeling and Performance Analysis of a Combined Power Generation System Based on HT-PEMFC and ORC

Author

Listed:
  • Hyun Sung Kang

    (Eco-Friendly Vehicle R & D Division, Korea Automotive Technology Institute, 303 Pungse-Ro, Pungse-Myeon, Cheonan-Si 330-912, Korea
    Department of Mechanical Engineering, Korea University, 409 Innovation Hall Building, Anam-Dong, Sungbuk-Gu, Seoul 02841, Korea)

  • Myong-Hwan Kim

    (Hydrogen Fuel Cell Mobility R&D Center, Korea Automotive Technology Institute, 303 Pungse-Ro, Pungse-Myeon, Cheonan-Si 330-912, Korea)

  • Yoon Hyuk Shin

    (Eco-Friendly Vehicle R & D Division, Korea Automotive Technology Institute, 303 Pungse-Ro, Pungse-Myeon, Cheonan-Si 330-912, Korea)

Abstract

Recently, the need for energy-saving and eco-friendly energy systems is increasing as problems such as rapid climate change and air pollution are getting more serious. While research on a power generation system using hydrogen energy-based fuel cells, which rarely generates harmful substances unlike fossil fuels, is being done, a power generation system that combines fuel cells and Organic Rankine Cycle (ORC) is being recognized. In the case of High Temperature Proton Exchange Membrane Fuel Cell (HT-PEMFC) with an operating temperature of approximately 150 to 200 °C, the importance of a thermal management system increases. It also produces the waste heat energy at a relatively high temperature, so it can be used as a heat source for ORC system. In order to achieve this outcome, waste heat must be used on a limited scale within a certain range of the temperature of the stack coolant. Therefore, it is necessary to utilize the waste heat of ORC system reflecting the stack thermal management and to establish and predict an appropriate operating range. By constructing an analytical model of a combined power generation system of HT-PEMFC and ORC systems, this study compares the stack load and power generation performance and efficiency of the system by operating temperature. In the integrated lumped thermal capacity model, the effects of stack operating temperature and current density, which are important factors affecting the performance change of HT-PEMFC and ORC combined cycle power generation, were compared according to operating conditions. In the comparison of the change in power and waste heat generation of the HT-PEMFC stack, it was shown that the rate of change in power and waste heat generation by the stack operating temperature was clearly changed according to the current density. In the case of the ORC system, changes in the thermal efficiency of the ORC system according to the operating temperature of the stack and the environmental temperature (cooling temperature) of the object to which this system is applied were characteristic. This study is expected to contribute to the establishment of an optimal operation strategy and efficient system configuration according to the subjects of the HT-PEMFC and ORC combined power generation system in the future.

Suggested Citation

  • Hyun Sung Kang & Myong-Hwan Kim & Yoon Hyuk Shin, 2020. "Thermodynamic Modeling and Performance Analysis of a Combined Power Generation System Based on HT-PEMFC and ORC," Energies, MDPI, vol. 13(23), pages 1-18, November.
    • Handle: RePEc:gam:jeners:v:13:y:2020:i:23:p:6163-:d:450162
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/13/23/6163/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/13/23/6163/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Jannelli, Elio & Minutillo, Mariagiovanna & Perna, Alessandra, 2013. "Analyzing microcogeneration systems based on LT-PEMFC and HT-PEMFC by energy balances," Applied Energy, Elsevier, vol. 108(C), pages 82-91.
    2. Najafi, Behzad & Haghighat Mamaghani, Alireza & Rinaldi, Fabio & Casalegno, Andrea, 2015. "Long-term performance analysis of an HT-PEM fuel cell based micro-CHP system: Operational strategies," Applied Energy, Elsevier, vol. 147(C), pages 582-592.
    3. Hyun Sung Kang & Yoon Hyuk Shin, 2019. "Analytical Study of Tri-Generation System Integrated with Thermal Management Using HT-PEMFC Stack," Energies, MDPI, vol. 12(16), pages 1-17, August.
    4. Mohsen Kandidayeni & Alvaro Macias & Loïc Boulon & João Pedro F. Trovão, 2020. "Online Modeling of a Fuel Cell System for an Energy Management Strategy Design," Energies, MDPI, vol. 13(14), pages 1-17, July.
    5. Chang, Huawei & Wan, Zhongmin & Zheng, Yao & Chen, Xi & Shu, Shuiming & Tu, Zhengkai & Chan, Siew Hwa & Chen, Rui & Wang, Xiaodong, 2017. "Energy- and exergy-based working fluid selection and performance analysis of a high-temperature PEMFC-based micro combined cooling heating and power system," Applied Energy, Elsevier, vol. 204(C), pages 446-458.
    6. Tianqi He & Rongqi Shi & Jie Peng & Weilin Zhuge & Yangjun Zhang, 2016. "Waste Heat Recovery of a PEMFC System by Using Organic Rankine Cycle," Energies, MDPI, vol. 9(4), pages 1-15, April.
    7. Magdalena Dudek & Andrzej Raźniak & Maciej Rosół & Tomasz Siwek & Piotr Dudek, 2020. "Design, Development, and Performance of a 10 kW Polymer Exchange Membrane Fuel Cell Stack as Part of a Hybrid Power Source Designed to Supply a Motor Glider," Energies, MDPI, vol. 13(17), pages 1-29, August.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Viviana Cigolotti & Matteo Genovese & Petronilla Fragiacomo, 2021. "Comprehensive Review on Fuel Cell Technology for Stationary Applications as Sustainable and Efficient Poly-Generation Energy Systems," Energies, MDPI, vol. 14(16), pages 1-28, August.
    2. Guoqiang Wang & Feng Wang & Delun Guan, 2022. "A Study of Thermoelectric Generation Coupled with Methanol Steam Reforming for Hydrogen Production," Energies, MDPI, vol. 15(21), pages 1-11, November.
    3. Li, Yanju & Li, Dongxu & Ma, Zheshu & Zheng, Meng & Lu, Zhanghao & Song, Hanlin & Guo, Xinjia & Shao, Wei, 2022. "Performance analysis and optimization of a novel vehicular power system based on HT-PEMFC integrated methanol steam reforming and ORC," Energy, Elsevier, vol. 257(C).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Gabriele Loreti & Andrea Luigi Facci & Stefano Ubertini, 2021. "High-Efficiency Combined Heat and Power through a High-Temperature Polymer Electrolyte Membrane Fuel Cell and Gas Turbine Hybrid System," Sustainability, MDPI, vol. 13(22), pages 1-24, November.
    2. Víctor Sanz i López & Ramon Costa-Castelló & Carles Batlle, 2022. "Literature Review of Energy Management in Combined Heat and Power Systems Based on High-Temperature Proton Exchange Membrane Fuel Cells for Residential Comfort Applications," Energies, MDPI, vol. 15(17), pages 1-22, September.
    3. Haghighat Mamaghani, Alireza & Najafi, Behzad & Casalegno, Andrea & Rinaldi, Fabio, 2017. "Predictive modelling and adaptive long-term performance optimization of an HT-PEM fuel cell based micro combined heat and power (CHP) plant," Applied Energy, Elsevier, vol. 192(C), pages 519-529.
    4. Raffaello Cozzolino, 2018. "Thermodynamic Performance Assessment of a Novel Micro-CCHP System Based on a Low Temperature PEMFC Power Unit and a Half-Effect Li/Br Absorption Chiller," Energies, MDPI, vol. 11(2), pages 1-21, February.
    5. Chang, Huawei & Wan, Zhongmin & Zheng, Yao & Chen, Xi & Shu, Shuiming & Tu, Zhengkai & Chan, Siew Hwa & Chen, Rui & Wang, Xiaodong, 2017. "Energy- and exergy-based working fluid selection and performance analysis of a high-temperature PEMFC-based micro combined cooling heating and power system," Applied Energy, Elsevier, vol. 204(C), pages 446-458.
    6. Xia, Lingchao & Ni, Meng & He, Qijiao & Xu, Qidong & Cheng, Chun, 2021. "Optimization of gas diffusion layer in high temperature PEMFC with the focuses on thickness and porosity," Applied Energy, Elsevier, vol. 300(C).
    7. Li, Xueling & Chang, Huawei & Duan, Chen & Zheng, Yao & Shu, Shuiming, 2019. "Thermal performance analysis of a novel linear cavity receiver for parabolic trough solar collectors," Applied Energy, Elsevier, vol. 237(C), pages 431-439.
    8. Al Moussawi, Houssein & Fardoun, Farouk & Louahlia, Hasna, 2017. "Selection based on differences between cogeneration and trigeneration in various prime mover technologies," Renewable and Sustainable Energy Reviews, Elsevier, vol. 74(C), pages 491-511.
    9. Thomas, Sobi & Vang, Jakob Rabjerg & Araya, Samuel Simon & Kær, Søren Knudsen, 2017. "Experimental study to distinguish the effects of methanol slip and water vapour on a high temperature PEM fuel cell at different operating conditions," Applied Energy, Elsevier, vol. 192(C), pages 422-436.
    10. Xia, Lingchao & Ni, Meng & Xu, Qidong & Xu, Haoran & Zheng, Keqing, 2021. "Optimization of catalyst layer thickness for achieving high performance and low cost of high temperature proton exchange membrane fuel cell," Applied Energy, Elsevier, vol. 294(C).
    11. Fong, K.F. & Lee, C.K., 2015. "Performance analysis of internal-combustion-engine primed trigeneration systems for use in high-rise office buildings in Hong Kong," Applied Energy, Elsevier, vol. 160(C), pages 793-801.
    12. Assareh, Ehsanolah & Mousavi Asl, Seyed Sajad & Agarwal, Neha & Ahmadinejad, Mehrdad & Ghodrat, Maryam & Lee, Moonyong, 2023. "New optimized configuration for a hybrid PVT solar/electrolyzer/absorption chiller system utilizing the response surface method as a machine learning technique and multi-objective optimization," Energy, Elsevier, vol. 281(C).
    13. Zhang, S. & Reimer, U. & Beale, S.B. & Lehnert, W. & Stolten, D., 2019. "Modeling polymer electrolyte fuel cells: A high precision analysis," Applied Energy, Elsevier, vol. 233, pages 1094-1103.
    14. Alijanpour sheshpoli, Mohamad & Mousavi Ajarostaghi, Seyed Soheil & Delavar, Mojtaba Aghajani, 2018. "Waste heat recovery from a 1180 kW proton exchange membrane fuel cell (PEMFC) system by Recuperative organic Rankine cycle (RORC)," Energy, Elsevier, vol. 157(C), pages 353-366.
    15. Kwan, Trevor Hocksun & Wu, Xiaofeng & Yao, Qinghe, 2018. "Multi-objective genetic optimization of the thermoelectric system for thermal management of proton exchange membrane fuel cells," Applied Energy, Elsevier, vol. 217(C), pages 314-327.
    16. Asensio, F.J. & San Martín, J.I. & Zamora, I. & Oñederra, O., 2018. "Model for optimal management of the cooling system of a fuel cell-based combined heat and power system for developing optimization control strategies," Applied Energy, Elsevier, vol. 211(C), pages 413-430.
    17. Bizon, Nicu, 2014. "Tracking the maximum efficiency point for the FC system based on extremum seeking scheme to control the air flow," Applied Energy, Elsevier, vol. 129(C), pages 147-157.
    18. Guida, D. & Minutillo, M., 2017. "Design methodology for a PEM fuel cell power system in a more electrical aircraft," Applied Energy, Elsevier, vol. 192(C), pages 446-456.
    19. S. M. Seyed Mahmoudi & Niloufar Sarabchi & Mortaza Yari & Marc A. Rosen, 2019. "Exergy and Exergoeconomic Analyses of a Combined Power Producing System including a Proton Exchange Membrane Fuel Cell and an Organic Rankine Cycle," Sustainability, MDPI, vol. 11(12), pages 1-25, June.
    20. Purnima, P. & Jayanti, S., 2017. "Water neutrality and waste heat management in ethanol reformer - HTPEMFC integrated system for on-board hydrogen generation," Applied Energy, Elsevier, vol. 199(C), pages 169-179.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:13:y:2020:i:23:p:6163-:d:450162. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.