IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v11y2018i10p2684-d174360.html
   My bibliography  Save this article

A Micro Swing Rotor Engine and the Preliminary Study of Its Thermodynamic Characteristics

Author

Listed:
  • Chen Xia

    (College of Energy and Power Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China)

  • Zhiguang Zhang

    (College of Energy and Power Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China)

  • Guoping Huang

    (College of Energy and Power Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China)

  • Tong Zhou

    (College of Energy and Power Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China)

  • Jianhua Xu

    (College of Energy and Power Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China)

Abstract

The rapid progress in microelectromechanical system technology has facilitated great developments in micro heat engines, however, defects in these engines still need to be overcome. Thus, a novel four-stroke micro swing rotor engine (MSRE) that features the advantages of Wankel engine and the micro swing engine is proposed in this study. Kinematic and thermodynamic analyses of the MSRE were performed, and a preliminary experimental research was conducted. In the MSRE, the driver assembly was used to dominate the movements of the two rotors. By the design guideline adaptable to the engine operation principle, the volume of each chamber will vary in a sine-like waveform, which was validated by kinematic analyses. Then, a prototype in mesoscale was designed and fabricated. In consideration of the leakage effect, the thermodynamic characteristics of this engine were numerically investigated. Results indicate that the engine thermodynamic processes were seriously affected by leakage flow, especially when working at low frequencies. Gap height and operation frequency were the two dominant factors that affected engine performance. Under a certain gap height, the MSRE had to work at a specific frequency range and the corresponding optical values exist for engine efficiency and power. With a 20 μm height, the MSRE reached the maximum efficiency of 23.62% at 55 Hz and the maximum power of 3442 W at 95 Hz. Feasibility of the engine was further verified by an experimental test on the operation characteristics, including the cold state test with pressured air blow and the combustion test for engine operation at thermal state. This research lays a good foundation for future development of MSRE, which is of great practical significance for the progress in micro power systems.

Suggested Citation

  • Chen Xia & Zhiguang Zhang & Guoping Huang & Tong Zhou & Jianhua Xu, 2018. "A Micro Swing Rotor Engine and the Preliminary Study of Its Thermodynamic Characteristics," Energies, MDPI, vol. 11(10), pages 1-25, October.
    • Handle: RePEc:gam:jeners:v:11:y:2018:i:10:p:2684-:d:174360
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/11/10/2684/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/11/10/2684/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Chou, S.K. & Yang, W.M. & Chua, K.J. & Li, J. & Zhang, K.L., 2011. "Development of micro power generators - A review," Applied Energy, Elsevier, vol. 88(1), pages 1-16, January.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Jahangiri, M. & Asghari, M., 2023. "The strain gradient-based torsional vibration analysis of micro-rotors with nonlinear flexural-torsional coupling," Applied Mathematics and Computation, Elsevier, vol. 440(C).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Peng, Qingguo & Xie, Bo & Yang, Wenming & Tang, Shihao & Li, Zhenwei & Zhou, Peng & Luo, Ningkang, 2021. "Effects of porosity and multilayers of porous medium on the hydrogen-fueled combustion and micro-thermophotovoltaic," Renewable Energy, Elsevier, vol. 174(C), pages 391-402.
    2. Tang, Aikun & Deng, Jiang & Cai, Tao & Xu, Yiming & Pan, Jianfeng, 2017. "Combustion characteristics of premixed propane/hydrogen/air in the micro-planar combustor with different channel-heights," Applied Energy, Elsevier, vol. 203(C), pages 635-642.
    3. Rashid Naseer & Huliang Dai & Abdessattar Abdelkefi & Lin Wang, 2019. "Comparative Study of Piezoelectric Vortex-Induced Vibration-Based Energy Harvesters with Multi-Stability Characteristics," Energies, MDPI, vol. 13(1), pages 1-24, December.
    4. Vinay Sankar & Sreejith Sudarsanan & Sudipto Mukhopadhyay & Prabhu Selvaraj & Aravind Balakrishnan & Ratna Kishore Velamati, 2023. "Towards the Development of Miniature Scale Liquid Fuel Combustors for Power Generation Application—A Review," Energies, MDPI, vol. 16(10), pages 1-41, May.
    5. Jiaqiang, E. & Zuo, Wei & Liu, Xueling & Peng, Qingguo & Deng, Yuanwang & Zhu, Hao, 2016. "Effects of inlet pressure on wall temperature and exergy efficiency of the micro-cylindrical combustor with a step," Applied Energy, Elsevier, vol. 175(C), pages 337-345.
    6. Aravind Muraleedharan & Jithin Edacheri Veetil & Akram Mohammad & Sudarshan Kumar & Ratna Kishore Velamati, 2021. "Effect of Burner Wall Material on Microjet Hydrogen Diffusion Flames near Extinction: A Numerical Study," Energies, MDPI, vol. 14(24), pages 1-24, December.
    7. Jalal Zarvandi & Mohammadreza Baigmohammadi & Sadegh Tabejamaat, 2021. "A Numerical Study on the Effects of the Geometry and Location of an Inserted Wire on Methane–Air Flames in a Micro–Burner," Energies, MDPI, vol. 15(1), pages 1-11, December.
    8. Aravind, B. & Khandelwal, Bhupendra & Ramakrishna, P.A. & Kumar, Sudarshan, 2020. "Towards the development of a high power density, high efficiency, micro power generator," Applied Energy, Elsevier, vol. 261(C).
    9. Tang, Aikun & Cai, Tao & Deng, Jiang & Zhao, Dan & Huang, Qiuhan & Zhou, Chen, 2019. "Experimental study on flame structure transitions of premixed propane/air in micro-scale planar combustors," Energy, Elsevier, vol. 179(C), pages 558-570.
    10. Fanciulli, C. & Abedi, H. & Merotto, L. & Dondè, R. & De Iuliis, S. & Passaretti, F., 2018. "Portable thermoelectric power generation based on catalytic combustor for low power electronic equipment," Applied Energy, Elsevier, vol. 215(C), pages 300-308.
    11. Akhtar, Saad & Kurnia, Jundika C. & Shamim, Tariq, 2015. "A three-dimensional computational model of H2–air premixed combustion in non-circular micro-channels for a thermo-photovoltaic (TPV) application," Applied Energy, Elsevier, vol. 152(C), pages 47-57.
    12. Sark, W.G.J.H.M. van, 2011. "Feasibility of photovoltaic - Thermoelectric hybrid modules," Applied Energy, Elsevier, vol. 88(8), pages 2785-2790, August.
    13. Formosa, Fabien & Fréchette, Luc G., 2013. "Scaling laws for free piston Stirling engine design: Benefits and challenges of miniaturization," Energy, Elsevier, vol. 57(C), pages 796-808.
    14. Zuo, Wei & E, Jiaqiang & Liu, Haili & Peng, Qingguo & Zhao, Xiaohuan & Zhang, Zhiqing, 2016. "Numerical investigations on an improved micro-cylindrical combustor with rectangular rib for enhancing heat transfer," Applied Energy, Elsevier, vol. 184(C), pages 77-87.
    15. Gurunadh Velidi & Chun Sang Yoo, 2023. "A Review on Flame Stabilization Technologies for UAV Engine Micro-Meso Scale Combustors: Progress and Challenges," Energies, MDPI, vol. 16(9), pages 1-44, May.
    16. Yang, Wenming & Chou, Siawkiang & Chua, Kianjon & An, Hui & Karthikeyan, Kumarasamy & Zhao, Xing, 2012. "An advanced micro modular combustor-radiator with heat recuperation for micro-TPV system application," Applied Energy, Elsevier, vol. 97(C), pages 749-753.
    17. He, Zhi-Zhu, 2020. "A coupled electrical-thermal impedance matching model for design optimization of thermoelectric generator," Applied Energy, Elsevier, vol. 269(C).
    18. Ferrari, Claudio & Melino, Francesco & Pinelli, Michele & Spina, Pier Ruggero, 2014. "Thermophotovoltaic energy conversion: Analytical aspects, prototypes and experiences," Applied Energy, Elsevier, vol. 113(C), pages 1717-1730.
    19. Zuo, Wei & Zhang, Yuntian & Li, Qingqing & Li, Jing & He, Zhu, 2021. "Numerical investigations on hydrogen-fueled micro-cylindrical combustors with cavity for micro-thermophotovoltaic applications," Energy, Elsevier, vol. 223(C).
    20. Bani, Stephen & Pan, Jianfeng & Tang, Aikun & Lu, Qingbo & Zhang, Yi, 2018. "Numerical investigation of key parameters of the porous media combustion based Micro-Thermophotovoltaic system," Energy, Elsevier, vol. 157(C), pages 969-978.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:11:y:2018:i:10:p:2684-:d:174360. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.