IDEAS home Printed from https://ideas.repec.org/a/eee/renene/v242y2025ics0960148125001132.html
   My bibliography  Save this article

PCM melting characteristics in a sidewall-heated rectangular cavity with non-uniform longitudinal fins near the bottom

Author

Listed:
  • Liu, Hua-Yang
  • Hu, Yu-Peng
  • Yang, Guo-Yao
  • Wu, Chun-Mei
  • Li, You-Rong

Abstract

This paper employs three-dimensional numerical simulations to investigate the influences of adding non-uniform longitudinal fins near the bottom of a rectangular enclosure with a heated sidewall on the melting process of RT42. The focus is on enhancing natural convection, especially in the final melting stage. Using the longitudinal rectangular fins on the sidewall as a baseline case, we investigate the effects of the heights at the left (Ll) and right (Lr) sides of the fin, fin thicknesses (0.2, 0.25, and 0.3 mm), and the number of fins (1 or 2) on the heat storage characteristics. The results indicate that adding fins in the lower region of the container significantly improves energy storage efficiency. A greater right-side fin height demonstrates relatively superior melting performance. When fin thickness is 0.2 mm, the optimal non-uniform fin configuration (Case 8: Ll = 3 mm and Lr = 7 mm) reduces the melting time by 27.5 %, increases the energy storage rate by 37.3 %, and enhances the average Nusselt number by 28.5 % compared to the baseline case. Additionally, while double fins decrease the melting rate, they improve the uniformity of temperature distribution and enhance natural convection. Compared to the baseline case, the heat storage rate and the maximum average velocity increase by 56.3 % and 18.6 %, respectively.

Suggested Citation

  • Liu, Hua-Yang & Hu, Yu-Peng & Yang, Guo-Yao & Wu, Chun-Mei & Li, You-Rong, 2025. "PCM melting characteristics in a sidewall-heated rectangular cavity with non-uniform longitudinal fins near the bottom," Renewable Energy, Elsevier, vol. 242(C).
    • Handle: RePEc:eee:renene:v:242:y:2025:i:c:s0960148125001132
    DOI: 10.1016/j.renene.2025.122451
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0960148125001132
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.renene.2025.122451?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Xu, Yang & He, Chen & Chen, Yang & Sun, Yu & Yin, Hang & Zheng, Zhang-Jing, 2023. "Experimental and numerical study on the effect of the intelligent memory metal fin on the melting and solidification process of PCM," Renewable Energy, Elsevier, vol. 218(C).
    2. Huang, Yongping & Deng, Zilong & Chen, Yongping & Zhang, Chengbin, 2023. "Performance investigation of a biomimetic latent heat thermal energy storage device for waste heat recovery in data centers," Applied Energy, Elsevier, vol. 335(C).
    3. Huang, Xinyu & Li, Fangfei & Li, Yuanji & Meng, Xiangzhao & Yang, Xiaohu & Sundén, Bengt, 2023. "Optimization of melting performance of a heat storage tank under rotation conditions: Based on taguchi design and response surface method," Energy, Elsevier, vol. 271(C).
    4. Nakhchi, M.E. & Hatami, M. & Rahmati, M., 2021. "A numerical study on the effects of nanoparticles and stair fins on performance improvement of phase change thermal energy storages," Energy, Elsevier, vol. 215(PA).
    5. Huang, Yongping & Liu, Xiangdong, 2021. "Charging and discharging enhancement of a vertical latent heat storage unit by fractal tree-shaped fins," Renewable Energy, Elsevier, vol. 174(C), pages 199-217.
    6. Kirincic, Mateo & Trp, Anica & Lenic, Kristian & Batista, Josip, 2024. "Latent thermal energy storage performance enhancement through optimization of geometry parameters," Applied Energy, Elsevier, vol. 365(C).
    7. Dhaidan, Nabeel S. & Khodadadi, J.M., 2015. "Melting and convection of phase change materials in different shape containers: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 43(C), pages 449-477.
    8. Soni, Vikram & Kumar, Arvind & Jain, V.K., 2018. "Modeling of PCM melting: Analysis of discrepancy between numerical and experimental results and energy storage performance," Energy, Elsevier, vol. 150(C), pages 190-204.
    9. Kazemi, M. & Hosseini, M.J. & Ranjbar, A.A. & Bahrampoury, R., 2018. "Improvement of longitudinal fins configuration in latent heat storage systems," Renewable Energy, Elsevier, vol. 116(PA), pages 447-457.
    10. Najafpour, Nategheh & Adibi, Omid, 2024. "Investigating the effects of nano-enhanced phase change material on melting performance of LHTES with novel perforated hybrid stair fins," Energy, Elsevier, vol. 290(C).
    11. Zheng, Zhang-Jing & Yang, Chao & Xu, Yang & Cai, Xiao, 2021. "Effect of metal foam with two-dimensional porosity gradient on melting behavior in a rectangular cavity," Renewable Energy, Elsevier, vol. 172(C), pages 802-815.
    12. Liu, Zhan & Liu, Zihui & Liu, Gang & Yang, Xiaohu & Yan, Jinyue, 2022. "Melting assessment on the effect of nonuniform Y-shaped fin upon solid–liquid phase change in a thermal storage tank," Applied Energy, Elsevier, vol. 321(C).
    13. Dutil, Yvan & Rousse, Daniel R. & Salah, Nizar Ben & Lassue, Stéphane & Zalewski, Laurent, 2011. "A review on phase-change materials: Mathematical modeling and simulations," Renewable and Sustainable Energy Reviews, Elsevier, vol. 15(1), pages 112-130, January.
    14. Tao, Y.B. & He, Y.L., 2015. "Effects of natural convection on latent heat storage performance of salt in a horizontal concentric tube," Applied Energy, Elsevier, vol. 143(C), pages 38-46.
    15. Agyenim, Francis & Hewitt, Neil & Eames, Philip & Smyth, Mervyn, 2010. "A review of materials, heat transfer and phase change problem formulation for latent heat thermal energy storage systems (LHTESS)," Renewable and Sustainable Energy Reviews, Elsevier, vol. 14(2), pages 615-628, February.
    16. Liu, Zhan & Liu, Zihui & Guo, Junfei & Wang, Fan & Yang, Xiaohu & Yan, Jinyue, 2022. "Innovative ladder-shaped fin design on a latent heat storage device for waste heat recovery," Applied Energy, Elsevier, vol. 321(C).
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Grzegorz Czerwiński & Jerzy Wołoszyn, 2022. "Influence of the Longitudinal and Tree-Shaped Fin Parameters on the Shell-and-Tube LHTES Energy Efficiency," Energies, MDPI, vol. 16(1), pages 1-24, December.
    2. Mostafavi Tehrani, S. Saeed & Shoraka, Yashar & Diarce, Gonzalo & Taylor, Robert A., 2019. "An improved, generalized effective thermal conductivity method for rapid design of high temperature shell-and-tube latent heat thermal energy storage systems," Renewable Energy, Elsevier, vol. 132(C), pages 694-708.
    3. Hu, Zhipei & Jiang, Shuo & Sun, Zhigao & Li, Jun, 2024. "Numerical simulation of fin arrangements on the melting process of PCM in a rectangular unit," Renewable Energy, Elsevier, vol. 220(C).
    4. Muhammad Saqib & Rafal Andrzejczyk, 2023. "A review of phase change materials and heat enhancement methodologies," Wiley Interdisciplinary Reviews: Energy and Environment, Wiley Blackwell, vol. 12(3), May.
    5. Liu, Yang & Zheng, Ruowei & Li, Ji, 2022. "High latent heat phase change materials (PCMs) with low melting temperature for thermal management and storage of electronic devices and power batteries: Critical review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 168(C).
    6. Khan, Zakir & Khan, Zulfiqar Ahmad, 2017. "Experimental investigations of charging/melting cycles of paraffin in a novel shell and tube with longitudinal fins based heat storage design solution for domestic and industrial applications," Applied Energy, Elsevier, vol. 206(C), pages 1158-1168.
    7. Klimeš, Lubomír & Charvát, Pavel & Mastani Joybari, Mahmood & Zálešák, Martin & Haghighat, Fariborz & Panchabikesan, Karthik & El Mankibi, Mohamed & Yuan, Yanping, 2020. "Computer modelling and experimental investigation of phase change hysteresis of PCMs: The state-of-the-art review," Applied Energy, Elsevier, vol. 263(C).
    8. Huang, Shengyao & Lv, Laiquan & Rong, Yan & Zhou, Hao, 2024. "Experimental study on the thermal characteristics of a visualized shell-and-tube LHTES system at different endothermic and exothermic temperatures," Renewable Energy, Elsevier, vol. 221(C).
    9. Fei Ma & Tianji Zhu & Yalin Zhang & Xinli Lu & Wei Zhang & Feng Ma, 2023. "A Review on Heat Transfer Enhancement of Phase Change Materials Using Fin Tubes," Energies, MDPI, vol. 16(1), pages 1-25, January.
    10. Wang, Jiahao & Liu, Xiaomin & Desideri, Umberto, 2024. "Performance improvement evaluation of latent heat energy storage units using improved bi-objective topology optimization method," Applied Energy, Elsevier, vol. 364(C).
    11. Khan, Mohammed Mumtaz A. & Saidur, R. & Al-Sulaiman, Fahad A., 2017. "A review for phase change materials (PCMs) in solar absorption refrigeration systems," Renewable and Sustainable Energy Reviews, Elsevier, vol. 76(C), pages 105-137.
    12. Vogel, J. & Felbinger, J. & Johnson, M., 2016. "Natural convection in high temperature flat plate latent heat thermal energy storage systems," Applied Energy, Elsevier, vol. 184(C), pages 184-196.
    13. Zheng, Zhang-Jing & Cai, Xiao & Yang, Chao & Xu, Yang, 2022. "Improving the solidification performance of a latent heat thermal energy storage unit using arrow-shaped fins obtained by an innovative fast optimization algorithm," Renewable Energy, Elsevier, vol. 195(C), pages 566-577.
    14. Sharif, M.K. Anuar & Al-Abidi, A.A. & Mat, S. & Sopian, K. & Ruslan, M.H. & Sulaiman, M.Y. & Rosli, M.A.M., 2015. "Review of the application of phase change material for heating and domestic hot water systems," Renewable and Sustainable Energy Reviews, Elsevier, vol. 42(C), pages 557-568.
    15. Zhao, Dongliang & Tan, Gang, 2015. "Numerical analysis of a shell-and-tube latent heat storage unit with fins for air-conditioning application," Applied Energy, Elsevier, vol. 138(C), pages 381-392.
    16. Zeng, Kuo & Gao, Junjie & Lu, Yongwen & Zuo, Hongyang & Chi, Bowen & Fang, Zheyu & Li, Jun & Xu, Huaqian & Li, Beiyang & Yang, Haiping & Chen, Hanping, 2024. "Comprehensive enhancement of melting-solidifying process in latent heat storage based on eccentric fin-foam combination," Energy, Elsevier, vol. 313(C).
    17. Waqas, Adeel & Ud Din, Zia, 2013. "Phase change material (PCM) storage for free cooling of buildings—A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 18(C), pages 607-625.
    18. Tehrani, S. Saeed Mostafavi & Taylor, Robert A. & Saberi, Pouya & Diarce, Gonzalo, 2016. "Design and feasibility of high temperature shell and tube latent heat thermal energy storage system for solar thermal power plants," Renewable Energy, Elsevier, vol. 96(PA), pages 120-136.
    19. Yang, Chao & Xu, Xing-Rong & Bake, Maitiniyazi & Wu, Chun-Mei & Li, You-Rong & Zheng, Zhang-Jing & Yu, Jia-Jia, 2024. "Numerical investigation and optimization of the melting performance of latent heat thermal energy storage unit strengthened by graded metal foam and mechanical rotation," Renewable Energy, Elsevier, vol. 227(C).
    20. Zhang, Chengbin & Wang, Huijuan & Huang, Yongping & Zhang, Liangliang & Chen, Yongping, 2025. "Immersion liquid cooling for electronics: Materials, systems, applications and prospects," Renewable and Sustainable Energy Reviews, Elsevier, vol. 208(C).

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:renene:v:242:y:2025:i:c:s0960148125001132. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.journals.elsevier.com/renewable-energy .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.