IDEAS home Printed from https://ideas.repec.org/a/eee/renene/v154y2020icp1327-1345.html
   My bibliography  Save this article

Utilizing circular jet impingement to enhance thermal performance of solar air heater

Author

Listed:
  • Singh, Satyender
  • Chaurasiya, Shailendra Kumar
  • Negi, Bharat Singh
  • Chander, Subhash
  • Nemś, Magdalena
  • Negi, Sushant

Abstract

In the present work, the thermal performance of impinging jet double pass solar air heater is investigated experimentally. A corrugated wavy plate consists of circular holes, each of 7.66 mm in diameter on the crest region are used to provide the impinging jets of air that provide 1.4%–0.48% plate perforation. While, the double pass is provided by circulating the air first through the channel formed between back and lower corrugated plates and then through another wavy channel formed between two corrugated plates. To provide thermal backup and increase heat transfer to air, two design configurations are investigated i.e. Design-I without porous media (100% porosity) and Design-II with porous media (95%–98% porosity) in the wavy channel. Moreover, the deep insight on physics of fluid using CFD tool is presented in the extent of this work. It is recommended to operate the present solar air heater designs at the mass flow rate of 0.04 kg/s, bed porosity of 98% and impinging plate perforation of 0.48% to have the best thermal performance. Whereas, the maximum thermal efficiency and thermohydraulic efficiency of 94% and 84% is obtained for Design-I, which is about 7.5% and 19%, respectively high compared to Design-II.

Suggested Citation

  • Singh, Satyender & Chaurasiya, Shailendra Kumar & Negi, Bharat Singh & Chander, Subhash & Nemś, Magdalena & Negi, Sushant, 2020. "Utilizing circular jet impingement to enhance thermal performance of solar air heater," Renewable Energy, Elsevier, vol. 154(C), pages 1327-1345.
    • Handle: RePEc:eee:renene:v:154:y:2020:i:c:p:1327-1345
    DOI: 10.1016/j.renene.2020.03.095
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0960148120304274
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.renene.2020.03.095?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Dhiman, Prashant & Thakur, N.S. & Chauhan, S.R., 2012. "Thermal and thermohydraulic performance of counter and parallel flow packed bed solar air heaters," Renewable Energy, Elsevier, vol. 46(C), pages 259-268.
    2. Ho, C.D. & Yeh, H.M. & Cheng, T.W. & Chen, T.C. & Wang, R.C., 2009. "The influences of recycle on performance of baffled double-pass flat-plate solar air heaters with internal fins attached," Applied Energy, Elsevier, vol. 86(9), pages 1470-1478, September.
    3. Hernández, Alejandro L. & Quiñonez, José E., 2013. "Analytical models of thermal performance of solar air heaters of double-parallel flow and double-pass counter flow," Renewable Energy, Elsevier, vol. 55(C), pages 380-391.
    4. Singh, Satyender & Dhiman, Prashant, 2014. "Thermal and thermohydraulic performance evaluation of a novel type double pass packed bed solar air heater under external recycle using an analytical and RSM (response surface methodology) combined ap," Energy, Elsevier, vol. 72(C), pages 344-359.
    5. Ozgen, Filiz & Esen, Mehmet & Esen, Hikmet, 2009. "Experimental investigation of thermal performance of a double-flow solar air heater having aluminium cans," Renewable Energy, Elsevier, vol. 34(11), pages 2391-2398.
    6. Singh, Satyender, 2020. "Experimental and numerical investigations of a single and double pass porous serpentine wavy wiremesh packed bed solar air heater," Renewable Energy, Elsevier, vol. 145(C), pages 1361-1387.
    7. Omojaro, A.P. & Aldabbagh, L.B.Y., 2010. "Experimental performance of single and double pass solar air heater with fins and steel wire mesh as absorber," Applied Energy, Elsevier, vol. 87(12), pages 3759-3765, December.
    8. Naphon, Paisarn, 2005. "On the performance and entropy generation of the double-pass solar air heater with longitudinal fins," Renewable Energy, Elsevier, vol. 30(9), pages 1345-1357.
    9. Yeh, Ho-Ming & Ho, Chii-Dong, 2009. "Effect of external recycle on the performances of flat-plate solar air heaters with internal fins attached," Renewable Energy, Elsevier, vol. 34(5), pages 1340-1347.
    10. Chauhan, Ranchan & Thakur, N.S., 2014. "Investigation of the thermohydraulic performance of impinging jet solar air heater," Energy, Elsevier, vol. 68(C), pages 255-261.
    11. Ho, C.D. & Yeh, H.M. & Wang, R.C., 2005. "Heat-transfer enhancement in double-pass flat-plate solar air heaters with recycle," Energy, Elsevier, vol. 30(15), pages 2796-2817.
    12. El-Sebaii, A.A. & Aboul-Enein, S. & Ramadan, M.R.I. & Shalaby, S.M. & Moharram, B.M., 2011. "Thermal performance investigation of double pass-finned plate solar air heater," Applied Energy, Elsevier, vol. 88(5), pages 1727-1739, May.
    13. Mohammadi, K. & Sabzpooshani, M., 2013. "Comprehensive performance evaluation and parametric studies of single pass solar air heater with fins and baffles attached over the absorber plate," Energy, Elsevier, vol. 57(C), pages 741-750.
    14. Ho, Chii-Dong & Chang, Hsuan & Wang, Rei-Chi & Lin, Chun-Sheng, 2012. "Performance improvement of a double-pass solar air heater with fins and baffles under recycling operation," Applied Energy, Elsevier, vol. 100(C), pages 155-163.
    15. El-Sebaii, A.A. & Aboul-Enein, S. & Ramadan, M.R.I. & Shalaby, S.M. & Moharram, B.M., 2011. "Investigation of thermal performance of-double pass-flat and v-corrugated plate solar air heaters," Energy, Elsevier, vol. 36(2), pages 1076-1086.
    16. Ho, C.D. & Yeh, C.W. & Hsieh, S.M., 2005. "Improvement in device performance of multi-pass flat-plate solar air heaters with external recycle," Renewable Energy, Elsevier, vol. 30(10), pages 1601-1621.
    17. Dhiman, Prashant & Thakur, N.S. & Kumar, Anoop & Singh, Satyender, 2011. "An analytical model to predict the thermal performance of a novel parallel flow packed bed solar air heater," Applied Energy, Elsevier, vol. 88(6), pages 2157-2167, June.
    18. Aldabbagh, L.B.Y. & Egelioglu, F. & Ilkan, M., 2010. "Single and double pass solar air heaters with wire mesh as packing bed," Energy, Elsevier, vol. 35(9), pages 3783-3787.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Chaudhri, Kapil & Bhagoria, J.L. & Kumar, Vikash, 2022. "Transverse wedge-shaped rib roughened solar air heater (SAH) - Exergy based experimental investigation," Renewable Energy, Elsevier, vol. 184(C), pages 1150-1164.
    2. Tuncer, Azim Doğuş & Khanlari, Ataollah, 2023. "Improving the performance of a triple-flow solar air collector using recyclable aluminum cans as extended heat transfer surfaces: An energetic, exergetic, economic and environmental survey," Energy, Elsevier, vol. 282(C).
    3. Chaurasiya, Shailendra Kumar & Singh, Satyender, 2023. "High thermal performance of the solar air heater designs triggered by improved jet stability," Renewable Energy, Elsevier, vol. 204(C), pages 532-545.
    4. Liaqat Hussain & Muhammad Mahabat Khan & Manzar Masud & Fawad Ahmed & Zabdur Rehman & Łukasz Amanowicz & Krzysztof Rajski, 2021. "Heat Transfer Augmentation through Different Jet Impingement Techniques: A State-of-the-Art Review," Energies, MDPI, vol. 14(20), pages 1-40, October.
    5. Sheikhnejad, Yahya & Gandjalikhan Nassab, Seyed Abdolreza, 2021. "Enhancement of solar chimney performance by passive vortex generator," Renewable Energy, Elsevier, vol. 169(C), pages 437-450.
    6. Mahato, M.K. & Singh, S.N., 2024. "Effect of the partial blockage in the exit of the mixing channel on thermo - Hydraulic performance of the multi – Pass jet plate solar air heater," Renewable Energy, Elsevier, vol. 222(C).
    7. António Araújo, 2020. "Thermo-Hydraulic Performance of Solar Air Collectors with Artificially Roughened Absorbers: A Comparative Review of Semi-Empirical Models," Energies, MDPI, vol. 13(14), pages 1-33, July.
    8. Gürbüz, Emine Yağız & Şahinkesen, İstemihan & Kusun, Barış & Tuncer, Azim Doğuş & Keçebaş, Ali, 2023. "Enhancing the performance of an unglazed solar air collector using mesh tubes and Fe3O4 nano-enhanced absorber coating," Energy, Elsevier, vol. 277(C).
    9. Das, Biplab & Mondol, Jayanta Deb & Negi, Sushant & Smyth, Mervyn & Pugsley, Adrian, 2021. "Experimental performance analysis of a novel sand coated and sand filled polycarbonate sheet based solar air collector," Renewable Energy, Elsevier, vol. 164(C), pages 990-1004.
    10. Rajesh Maithani & Anil Kumar & Manoj Kumar & Sachin Sharma, 2022. "Sustainability and Cost Effectiveness Analysis of Staggered Jet Impingement on Solar Thermal Collector," Energies, MDPI, vol. 15(19), pages 1-19, October.
    11. Kumar, Raj & Kumar, Sushil & Nadda, Rahul & Kumar, Khusmeet & Goel, Varun, 2022. "Thermo-hydraulic efficiency and correlation development of an indoor designed jet impingement solar thermal collector roughened with discrete multi-arc ribs," Renewable Energy, Elsevier, vol. 189(C), pages 1259-1277.
    12. Kumar, Amit & Singh, Ajeet Pratap & Akshayveer, & Singh, O.P., 2022. "Performance characteristics of a new curved double-pass counter flow solar air heater," Energy, Elsevier, vol. 239(PA).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Singh, Satyender & Dhiman, Prashant, 2016. "Thermal performance of double pass packed bed solar air heaters – A comprehensive review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 53(C), pages 1010-1031.
    2. Alam, Tabish & Kim, Man-Hoe, 2017. "Performance improvement of double-pass solar air heater – A state of art of review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 79(C), pages 779-793.
    3. Ravi, Ravi Kant & Saini, Rajeshwer Prasad, 2016. "A review on different techniques used for performance enhancement of double pass solar air heaters," Renewable and Sustainable Energy Reviews, Elsevier, vol. 56(C), pages 941-952.
    4. Singh, Satyender & Dhiman, Prashant, 2014. "Thermal and thermohydraulic performance evaluation of a novel type double pass packed bed solar air heater under external recycle using an analytical and RSM (response surface methodology) combined ap," Energy, Elsevier, vol. 72(C), pages 344-359.
    5. Oztop, Hakan F. & Bayrak, Fatih & Hepbasli, Arif, 2013. "Energetic and exergetic aspects of solar air heating (solar collector) systems," Renewable and Sustainable Energy Reviews, Elsevier, vol. 21(C), pages 59-83.
    6. Hassan, Hamdy & Abo-Elfadl, Saleh, 2018. "Experimental study on the performance of double pass and two inlet ports solar air heater (SAH) at different configurations of the absorber plate," Renewable Energy, Elsevier, vol. 116(PA), pages 728-740.
    7. Varun Pratap Singh & Siddharth Jain & Ashish Karn & Ashwani Kumar & Gaurav Dwivedi & Chandan Swaroop Meena & Nitesh Dutt & Aritra Ghosh, 2022. "Recent Developments and Advancements in Solar Air Heaters: A Detailed Review," Sustainability, MDPI, vol. 14(19), pages 1-55, September.
    8. Kabeel, A.E. & Hamed, Mofreh H. & Omara, Z.M. & Kandeal, A.W., 2017. "Solar air heaters: Design configurations, improvement methods and applications – A detailed review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 70(C), pages 1189-1206.
    9. Sabzpooshani, M. & Mohammadi, K. & Khorasanizadeh, H., 2014. "Exergetic performance evaluation of a single pass baffled solar air heater," Energy, Elsevier, vol. 64(C), pages 697-706.
    10. Yu Wang & Mikael Boulic & Robyn Phipps & Manfred Plagmann & Chris Cunningham, 2020. "Experimental Performance of a Solar Air Collector with a Perforated Back Plate in New Zealand," Energies, MDPI, vol. 13(6), pages 1-16, March.
    11. Saxena, Abhishek & Varun, & El-Sebaii, A.A., 2015. "A thermodynamic review of solar air heaters," Renewable and Sustainable Energy Reviews, Elsevier, vol. 43(C), pages 863-890.
    12. Fudholi, Ahmad & Sopian, Kamaruzzaman, 2019. "A review of solar air flat plate collector for drying application," Renewable and Sustainable Energy Reviews, Elsevier, vol. 102(C), pages 333-345.
    13. Kumar, Amit & Akshayveer, & Singh, Ajeet Pratap & Singh, O.P., 2020. "Efficient designs of double-pass curved solar air heaters," Renewable Energy, Elsevier, vol. 160(C), pages 1105-1118.
    14. Rajarajeswari, K. & Sreekumar, A., 2016. "Matrix solar air heaters – A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 57(C), pages 704-712.
    15. Singh, Sukhmeet & Chander, Subhash & Saini, J.S., 2012. "Investigations on thermo-hydraulic performance due to flow-attack-angle in V-down rib with gap in a rectangular duct of solar air heater," Applied Energy, Elsevier, vol. 97(C), pages 907-912.
    16. Kumar, Rajesh & Chand, Prabha, 2017. "Performance enhancement of solar air heater using herringbone corrugated fins," Energy, Elsevier, vol. 127(C), pages 271-279.
    17. Das, Biplab & Mondol, Jayanta Deb & Debnath, Suman & Pugsley, Adrian & Smyth, Mervyn & Zacharopoulos, A., 2020. "Effect of the absorber surface roughness on the performance of a solar air collector: An experimental investigation," Renewable Energy, Elsevier, vol. 152(C), pages 567-578.
    18. Nowzari, Raheleh & Aldabbagh, L.B.Y. & Egelioglu, F., 2014. "Single and double pass solar air heaters with partially perforated cover and packed mesh," Energy, Elsevier, vol. 73(C), pages 694-702.
    19. Dhiman, Prashant & Thakur, N.S. & Chauhan, S.R., 2012. "Thermal and thermohydraulic performance of counter and parallel flow packed bed solar air heaters," Renewable Energy, Elsevier, vol. 46(C), pages 259-268.
    20. Hassan, Hamdy & Abo-Elfadl, Saleh & El-Dosoky, M.F., 2020. "An experimental investigation of the performance of new design of solar air heater (tubular)," Renewable Energy, Elsevier, vol. 151(C), pages 1055-1066.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:renene:v:154:y:2020:i:c:p:1327-1345. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.journals.elsevier.com/renewable-energy .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.