IDEAS home Printed from https://ideas.repec.org/a/eee/energy/v267y2023ics036054422203482x.html
   My bibliography  Save this article

Waste to fuel: Pyrolysis of waste transformer oil and its evaluation as alternative fuel along with different nanoparticles in CI engine with exhaust gas recirculation

Author

Listed:
  • Sathish, Thanikodi
  • Surakasi, Raviteja
  • KishoreT, Lakshmana
  • Rathinasamy, Saravanan
  • Ağbulut, Ümit
  • Shaik, Saboor
  • Park, Sung Goon
  • Afzal, Asif

Abstract

The present research aims to produce the alternative fuel from waste electric transformer oil through two levels pyrolysis process with potassium hydroxide catalyst, enhance it by 150 ppm of 30–50 nm sized Zinc oxide and Cerium oxide nanoparticles and then tested with/without EGR method to achieve low exhaust emissions. The experiments were performed on a single-cylinder, four-stroke CI engine at varying engine loads from 0 to 100% with an increment of 25% at a fixed engine speed of 1500 rpm. The results obtained from the combined test fuels have been compared with reference (conventional) diesel fuel. The performance of fuels like Diesel, PBWTO, PBWTO/ZnO, PBWTO/CeO2, and with working conditions like PBWTO/ZnO +20% EGR and PBWTO/CeO2 +20% EGR were recorded respectively at full load conditions in which HC emission as 11, 19, 14, 13, 15 and 15 ppm, 32.9%, smoke opacity as 32.9%, 39.5%, 16.6%, 19.3%, 20.1%. WTO addition into diesel fuel increased the CO emission; however, it is reduced with the nanoparticle addition. That is, PBWTO/ZnO, PBWTO/CeO2, PBWTO/ZnO +20% EGR and PBWTO/CeO2 +20% EGR have produced 0.058%, 0.046%, 0.056%, and 0.043% of lesser CO emission than PBWTO fuel respectively. In particular, EGR ensured noteworthy NOx emissions. For example, D, PBWTO, PBWTO/ZnO, PBWTO/CeO2, PBWTO/ZnO +20% EGR and PBWTO/CeO2 +20% EGR have emitted 1248 ppm, 1427 ppm, 1484 ppm, 1156 ppm, 831 ppm and 821 ppm of NOx emission, respectively. Due to the lower calorific value, higher viscosity, and poor atomization of WTO-added test fuels, the engine performance worsened. Accordingly, under full load condition, BTE was found to be 30.12%, 27.35%, 25.44%, 26.04%, 24.67%, and 25.26%, and BSFC was calculated to be 342, 410, 456, 450, 470, and 459 g/kWh for D, PBWTO, PBWTO/ZnO, PBWTO/CeO2, PBWTO/ZnO +20% EGR and PBWTO/CeO2 +20% EGR, respectively. In the conclusion, it is well-noticed that waste transformer oil can be used as a fuel substitute in CI engines with no modification on the vehicular system, and the addition of nanoparticles is a very good solution to mitigate the high exhaust pollutants arising from the use of WTO substitutes.

Suggested Citation

  • Sathish, Thanikodi & Surakasi, Raviteja & KishoreT, Lakshmana & Rathinasamy, Saravanan & Ağbulut, Ümit & Shaik, Saboor & Park, Sung Goon & Afzal, Asif, 2023. "Waste to fuel: Pyrolysis of waste transformer oil and its evaluation as alternative fuel along with different nanoparticles in CI engine with exhaust gas recirculation," Energy, Elsevier, vol. 267(C).
    • Handle: RePEc:eee:energy:v:267:y:2023:i:c:s036054422203482x
    DOI: 10.1016/j.energy.2022.126595
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S036054422203482X
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.energy.2022.126595?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Karagoz, Mustafa & Uysal, Cuneyt & Agbulut, Umit & Saridemir, Suat, 2021. "Exergetic and exergoeconomic analyses of a CI engine fueled with diesel-biodiesel blends containing various metal-oxide nanoparticles," Energy, Elsevier, vol. 214(C).
    2. Kasiraman, G. & Edwin Geo, V. & Nagalingam, B., 2016. "Assessment of cashew nut shell oil as an alternate fuel for CI (Compression ignition) engines," Energy, Elsevier, vol. 101(C), pages 402-410.
    3. Krzywanski, J. & Czakiert, T. & Nowak, W. & Shimizu, T. & Zylka, A. & Idziak, K. & Sosnowski, M. & Grabowska, K., 2022. "Gaseous emissions from advanced CLC and oxyfuel fluidized bed combustion of coal and biomass in a complex geometry facility:A comprehensive model," Energy, Elsevier, vol. 251(C).
    4. Thangaraja, J. & Kannan, C., 2016. "Effect of exhaust gas recirculation on advanced diesel combustion and alternate fuels - A review," Applied Energy, Elsevier, vol. 180(C), pages 169-184.
    5. Ooi, Jong Boon & Ismail, Harun Mohamed & Tan, Boon Thong & Wang, Xin, 2018. "Effects of graphite oxide and single-walled carbon nanotubes as diesel additives on the performance, combustion, and emission characteristics of a light-duty diesel engine," Energy, Elsevier, vol. 161(C), pages 70-80.
    6. Suresh, M. & Jawahar, C.P. & Richard, Arun, 2018. "A review on biodiesel production, combustion, performance, and emission characteristics of non-edible oils in variable compression ratio diesel engine using biodiesel and its blends," Renewable and Sustainable Energy Reviews, Elsevier, vol. 92(C), pages 38-49.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Sivasankar, G.A. & Moorthy, C. Balakrishna & Kaliappan, Seeniappan & Sathyamurthy, Ravishankar & Sathish, T. & Saravanan, R. & Ağbulut, Ümit, 2023. "Sustainable nano-added biofuel production from borassus flabellifer oil for conventional internal combustion engines," Energy, Elsevier, vol. 282(C).
    2. Jegan, C. Dhayananth & Selvakumaran, T. & Karthe, M. & Hemachandu, P. & Gopinathan, R. & Sathish, T. & Ağbulut, Ümit, 2023. "Influences of various metal oxide-based nanosized particles-added algae biodiesel on engine characteristics," Energy, Elsevier, vol. 284(C).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Ağbulut, Ümit & Gürel, Ali Etem & Sarıdemir, Suat, 2021. "Experimental investigation and prediction of performance and emission responses of a CI engine fuelled with different metal-oxide based nanoparticles–diesel blends using different machine learning alg," Energy, Elsevier, vol. 215(PA).
    2. Das, Amar Kumar & Hansdah, Dulari & Panda, Achyut Kumar, 2021. "Thermal balancing and exergetic performance evaluation of a compression ignition engine fuelled with waste plastic pyrolytic oil and different fuel additives," Energy, Elsevier, vol. 229(C).
    3. K. M. V. Ravi Teja & P. Issac Prasad & K. Vijaya Kumar Reddy & N. R. Banapurmath & Manzoore Elahi M. Soudagar & T. M. Yunus Khan & Irfan Anjum Badruddin, 2021. "Influence of Combustion Chamber Shapes and Nozzle Geometry on Performance, Emission, and Combustion Characteristics of CRDI Engine Powered with Biodiesel Blends," Sustainability, MDPI, vol. 13(17), pages 1-19, August.
    4. Khoa, Nguyen Xuan & Lim, Ocktaeck, 2019. "The effects of combustion duration on residual gas, effective release energy, engine power and engine emissions characteristics of the motorcycle engine," Applied Energy, Elsevier, vol. 248(C), pages 54-63.
    5. Aboelazayem, Omar & Gadalla, Mamdouh & Saha, Basudeb, 2019. "Derivatisation-free characterisation and supercritical conversion of free fatty acids into biodiesel from high acid value waste cooking oil," Renewable Energy, Elsevier, vol. 143(C), pages 77-90.
    6. Ooi, Jong Boon & Kau, Chia Chuin & Manoharan, Dilrukshan Naveen & Wang, Xin & Tran, Manh-Vu & Hung, Yew Mun, 2023. "Effects of multi-walled carbon nanotubes on the combustion, performance, and emission characteristics of a single-cylinder diesel engine fueled with palm-oil biodiesel-diesel blend," Energy, Elsevier, vol. 281(C).
    7. Singh, Paramvir & Chauhan, S.R. & Goel, Varun, 2018. "Assessment of diesel engine combustion, performance and emission characteristics fuelled with dual fuel blends," Renewable Energy, Elsevier, vol. 125(C), pages 501-510.
    8. Wang, Guotao & Liao, Qi & Wang, Chang & Liang, Yongtu & Zhang, Haoran, 2022. "Multiperiod optimal planning of biofuel refueling stations: A bi-level game-theoretic approach," Renewable Energy, Elsevier, vol. 200(C), pages 1152-1165.
    9. Pachiannan, Tamilselvan & Zhong, Wenjun & Rajkumar, Sundararajan & He, Zhixia & Leng, Xianying & Wang, Qian, 2019. "A literature review of fuel effects on performance and emission characteristics of low-temperature combustion strategies," Applied Energy, Elsevier, vol. 251(C), pages 1-1.
    10. Hu, Wenshuo & Zhang, Yu & Wang, Xiaoxiang & Wu, Weihong & Song, Hao & Yang, Yang & Liu, Shaojun & Zheng, Chenghang & Gao, Xiang, 2023. "Mechanistic assessment of NO oxidative activation on tungsten-promoted ceria catalysts and its consequence for low-temperature NH3-SCR," Applied Energy, Elsevier, vol. 330(PA).
    11. Xu Zheng & Nan Zhou & Quan Zhou & Yi Qiu & Ruijun Liu & Zhiyong Hao, 2020. "Experimental Investigation on the High-frequency Pressure Oscillation Characteristics of a Combustion Process in a DI Diesel Engine," Energies, MDPI, vol. 13(4), pages 1-25, February.
    12. Ziqiang Yang & Fenghai Li & Mingjie Ma & Xuefei Liu & Hongli Fan & Zhenzhu Li & Yong Wang & Yitian Fang, 2023. "Regulation Mechanism of Solid Waste on Ash Fusion Characteristics of Sorghum Straw under O 2 /CO 2 Atmosphere," Energies, MDPI, vol. 16(20), pages 1-17, October.
    13. K. M. V. Ravi Teja & P. Issac Prasad & K. Vijaya Kumar Reddy & Nagaraj R. Banapurmath & Muhammad A. Kalam & C. Ahamed Saleel, 2022. "Effect of Injection Parameters on the Performance of Compression Ignition Engine Powered with Jamun Seed and Cashew Nutshell B20 Biodiesel Blends," Sustainability, MDPI, vol. 14(8), pages 1-18, April.
    14. Soto, Felipe & Marques, Gian & Torres-Jiménez, E. & Vieira, Bráulio & Lacerda, André & Armas, Octavio & Guerrero-Villar, F., 2019. "A comparative study of performance and regulated emissions in a medium-duty diesel engine fueled with sugarcane diesel-farnesane and sugarcane biodiesel-LS9," Energy, Elsevier, vol. 176(C), pages 392-409.
    15. Tayari, Sara & Abedi, Reza & Rahi, Abbas, 2020. "Comparative assessment of engine performance and emissions fueled with three different biodiesel generations," Renewable Energy, Elsevier, vol. 147(P1), pages 1058-1069.
    16. Hoang, Anh Tuan & Tabatabaei, Meisam & Aghbashlo, Mortaza & Carlucci, Antonio Paolo & Ölçer, Aykut I. & Le, Anh Tuan & Ghassemi, Abbas, 2021. "Rice bran oil-based biodiesel as a promising renewable fuel alternative to petrodiesel: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 135(C).
    17. Nguyen Xuan Khoa & Ocktaeck Lim, 2022. "A Review of the External and Internal Residual Exhaust Gas in the Internal Combustion Engine," Energies, MDPI, vol. 15(3), pages 1-21, February.
    18. Ağbulut, Ümit & Elibol, Erdem & Demirci, Tuna & Sarıdemir, Suat & Gürel, Ali Etem & Rajak, Upendra & Afzal, Asif & Verma, Tikendra Nath, 2022. "Synthesis of graphene oxide nanoparticles and the influences of their usage as fuel additives on CI engine behaviors," Energy, Elsevier, vol. 244(PA).
    19. Zhu, Shujun & Hui, Jicheng & Lyu, Qinggang & Ouyang, Ziqu & Zeng, Xiongwei & Zhu, Jianguo & Liu, Jingzhang & Cao, Xiaoyang & Zhang, Xiaoyu & Ding, Hongliang & Liu, Yuhua, 2023. "Experimental study on pulverized coal swirl-opposed combustion preheated by a circulating fluidized bed. Part A. Wide-load operation and low-NOx emission characteristics," Energy, Elsevier, vol. 284(C).
    20. S, Prabakaran & T, Mohanraj & A, Arumugam, 2021. "Azolla pinnata methyl ester production and process optimization using a novel heterogeneous catalyst," Renewable Energy, Elsevier, vol. 180(C), pages 353-371.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:energy:v:267:y:2023:i:c:s036054422203482x. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.journals.elsevier.com/energy .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.