IDEAS home Printed from https://ideas.repec.org/a/eee/energy/v195y2020ics0360544219325873.html
   My bibliography  Save this article

3D-printing of shape-controllable thermoelectric devices with enhanced output performance

Author

Listed:
  • Su, Ning
  • Zhu, Pengfei
  • Pan, Yuhui
  • Li, Fu
  • Li, Bo

Abstract

Reducing the heat loss between thermoelectric (TE) devices and heat sources is an important factor to improve the conversion efficiency of the devices. Direct-writing three-dimensional (3D) printing technology, which is a bottom-up additive manufacturing method, can produce complex structures that cannot be formed by traditional preparation methods and also has more flexibility in the design of structural parameters. In this work, TE materials consisting of Bi2Te3/polyvinylpyrrolidone (PVP) and Bi0.5Sb1.5Te3/PVP composites with different contents of TE fillers and heat treatment times were synthesized by direct-writing 3D printing technology. The results showed that the sample containing 91 wt% TE filler displayed maximum figure of merit values of 0.104 (p-type) and 0.11 (n-type) after heat treatment for 6 h. The in-plane and annular TE devices were then printed by direct-writing technology and their output performance was measured. The annular device displayed an open-circuit voltage of 60.80 mV and maximum output power of 0.68 mW when the temperature difference was 54.6 K, which were consistent with the results obtained for simulations using the finite element method. Both the experimental and simulation results indicated that direct-writing 3D printing is an effective approach to fabricate TE materials and devices with excellent performance at room temperature. The shape-controllable TE devices can be applied to any shape of heat source to minimize heat loss.

Suggested Citation

  • Su, Ning & Zhu, Pengfei & Pan, Yuhui & Li, Fu & Li, Bo, 2020. "3D-printing of shape-controllable thermoelectric devices with enhanced output performance," Energy, Elsevier, vol. 195(C).
    • Handle: RePEc:eee:energy:v:195:y:2020:i:c:s0360544219325873
    DOI: 10.1016/j.energy.2019.116892
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0360544219325873
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.energy.2019.116892?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Fredrick Kim & Beomjin Kwon & Youngho Eom & Ji Eun Lee & Sangmin Park & Seungki Jo & Sung Hoon Park & Bong-Seo Kim & Hye Jin Im & Min Ho Lee & Tae Sik Min & Kyung Tae Kim & Han Gi Chae & William P. Ki, 2018. "3D printing of shape-conformable thermoelectric materials using all-inorganic Bi2Te3-based inks," Nature Energy, Nature, vol. 3(4), pages 301-309, April.
    2. Liu, Di & Cai, Yang & Zhao, Fu-Yun, 2017. "Optimal design of thermoelectric cooling system integrated heat pipes for electric devices," Energy, Elsevier, vol. 128(C), pages 403-413.
    3. He, Wei & Zhang, Gan & Zhang, Xingxing & Ji, Jie & Li, Guiqiang & Zhao, Xudong, 2015. "Recent development and application of thermoelectric generator and cooler," Applied Energy, Elsevier, vol. 143(C), pages 1-25.
    4. Xiao, Jinsheng & Yang, Tianqi & Li, Peng & Zhai, Pengcheng & Zhang, Qingjie, 2012. "Thermal design and management for performance optimization of solar thermoelectric generator," Applied Energy, Elsevier, vol. 93(C), pages 33-38.
    5. Hamid Elsheikh, Mohamed & Shnawah, Dhafer Abdulameer & Sabri, Mohd Faizul Mohd & Said, Suhana Binti Mohd & Haji Hassan, Masjuki & Ali Bashir, Mohamed Bashir & Mohamad, Mahazani, 2014. "A review on thermoelectric renewable energy: Principle parameters that affect their performance," Renewable and Sustainable Energy Reviews, Elsevier, vol. 30(C), pages 337-355.
    6. Siddique, Abu Raihan Mohammad & Rabari, Ronil & Mahmud, Shohel & Heyst, Bill Van, 2016. "Thermal energy harvesting from the human body using flexible thermoelectric generator (FTEG) fabricated by a dispenser printing technique," Energy, Elsevier, vol. 115(P1), pages 1081-1091.
    7. Li, Siyang & Pei, Jun & Liu, Dawei & Bao, Liangliang & Li, Jing-Feng & Wu, Huaqiang & Li, Liangliang, 2016. "Fabrication and characterization of thermoelectric power generators with segmented legs synthesized by one-step spark plasma sintering," Energy, Elsevier, vol. 113(C), pages 35-43.
    8. Dunham, Marc T. & Barako, Michael T. & LeBlanc, Saniya & Asheghi, Mehdi & Chen, Baoxing & Goodson, Kenneth E., 2015. "Power density optimization for micro thermoelectric generators," Energy, Elsevier, vol. 93(P2), pages 2006-2017.
    9. Tian, Hua & Sun, Xiuxiu & Jia, Qi & Liang, Xingyu & Shu, Gequn & Wang, Xu, 2015. "Comparison and parameter optimization of a segmented thermoelectric generator by using the high temperature exhaust of a diesel engine," Energy, Elsevier, vol. 84(C), pages 121-130.
    10. Lan, Song & Yang, Zhijia & Chen, Rui & Stobart, Richard, 2018. "A dynamic model for thermoelectric generator applied to vehicle waste heat recovery," Applied Energy, Elsevier, vol. 210(C), pages 327-338.
    11. Sung Hoon Park & Seungki Jo & Beomjin Kwon & Fredrick Kim & Hyeong Woo Ban & Ji Eun Lee & Da Hwi Gu & Se Hwa Lee & Younghun Hwang & Jin-Sang Kim & Dow-Bin Hyun & Sukbin Lee & Kyoung Jin Choi & Wook Jo, 2016. "High-performance shape-engineerable thermoelectric painting," Nature Communications, Nature, vol. 7(1), pages 1-10, December.
    12. Manikandan, S. & Kaushik, S.C., 2016. "The influence of Thomson effect in the performance optimization of a two stage thermoelectric generator," Energy, Elsevier, vol. 100(C), pages 227-237.
    13. Song, Haijun & Cai, Kefeng, 2017. "Preparation and properties of PEDOT:PSS/Te nanorod composite films for flexible thermoelectric power generator," Energy, Elsevier, vol. 125(C), pages 519-525.
    14. Zhu, Wei & Deng, Yuan & Gao, Min & Wang, Yao & Cui, Jiaolin & Gao, Hongli, 2015. "Thin-film solar thermoelectric generator with enhanced power output: Integrated optimization design to obtain directional heat flow," Energy, Elsevier, vol. 89(C), pages 106-117.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Cagri Oztan & Ryan Welch & Saniya LeBlanc, 2022. "Additive Manufacturing of Bulk Thermoelectric Architectures: A Review," Energies, MDPI, vol. 15(9), pages 1-16, April.
    2. Gokan May & Foivos Psarommatis, 2023. "Maximizing Energy Efficiency in Additive Manufacturing: A Review and Framework for Future Research," Energies, MDPI, vol. 16(10), pages 1-28, May.
    3. Tianbo Lu & Yuqiang Li & Jianxin Zhang & Pingfan Ning & Pingjuan Niu, 2020. "Cooling and Mechanical Performance Analysis of a Trapezoidal Thermoelectric Cooler with Variable Cross-Section," Energies, MDPI, vol. 13(22), pages 1-19, November.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Shittu, Samson & Li, Guiqiang & Zhao, Xudong & Ma, Xiaoli, 2020. "Review of thermoelectric geometry and structure optimization for performance enhancement," Applied Energy, Elsevier, vol. 268(C).
    2. Liu, Shuang & Hu, Bingkun & Liu, Dawei & Li, Fu & Li, Jing-Feng & Li, Bo & Li, Liangliang & Lin, Yuan-Hua & Nan, Ce-Wen, 2018. "Micro-thermoelectric generators based on through glass pillars with high output voltage enabled by large temperature difference," Applied Energy, Elsevier, vol. 225(C), pages 600-610.
    3. Ge, Ya & Liu, Zhichun & Sun, Henan & Liu, Wei, 2018. "Optimal design of a segmented thermoelectric generator based on three-dimensional numerical simulation and multi-objective genetic algorithm," Energy, Elsevier, vol. 147(C), pages 1060-1069.
    4. Zhang, Houcheng & Xu, Haoran & Chen, Bin & Dong, Feifei & Ni, Meng, 2017. "Two-stage thermoelectric generators for waste heat recovery from solid oxide fuel cells," Energy, Elsevier, vol. 132(C), pages 280-288.
    5. Eom, Yoomin & Wijethunge, Dimuthu & Park, Hwanjoo & Park, Sang Hyun & Kim, Woochul, 2017. "Flexible thermoelectric power generation system based on rigid inorganic bulk materials," Applied Energy, Elsevier, vol. 206(C), pages 649-656.
    6. Hancock, Asher J. & Fulton, Laura B. & Ying, Justin & Clifford, Corey E. & Sammak, Shervin & Barry, Matthew M., 2021. "A GPU-Accelerated ray-tracing method for determining radiation view factors in multi-junction thermoelectric generators," Energy, Elsevier, vol. 228(C).
    7. Ravi Anant Kishore & Roop L. Mahajan & Shashank Priya, 2018. "Combinatory Finite Element and Artificial Neural Network Model for Predicting Performance of Thermoelectric Generator," Energies, MDPI, vol. 11(9), pages 1-17, August.
    8. Shu, Gequn & Ma, Xiaonan & Tian, Hua & Yang, Haoqi & Chen, Tianyu & Li, Xiaoya, 2018. "Configuration optimization of the segmented modules in an exhaust-based thermoelectric generator for engine waste heat recovery," Energy, Elsevier, vol. 160(C), pages 612-624.
    9. Ding, L.C. & Akbarzadeh, A. & Tan, L., 2018. "A review of power generation with thermoelectric system and its alternative with solar ponds," Renewable and Sustainable Energy Reviews, Elsevier, vol. 81(P1), pages 799-812.
    10. Cui, Tengfei & Xuan, Yimin & Yin, Ershuai & Li, Qiang & Li, Dianhong, 2017. "Experimental investigation on potential of a concentrated photovoltaic-thermoelectric system with phase change materials," Energy, Elsevier, vol. 122(C), pages 94-102.
    11. Soprani, S. & Haertel, J.H.K. & Lazarov, B.S. & Sigmund, O. & Engelbrecht, K., 2016. "A design approach for integrating thermoelectric devices using topology optimization," Applied Energy, Elsevier, vol. 176(C), pages 49-64.
    12. Yin, Ershuai & Li, Qiang & Xuan, Yimin, 2018. "Optimal design method for concentrating photovoltaic-thermoelectric hybrid system," Applied Energy, Elsevier, vol. 226(C), pages 320-329.
    13. Jia, Xiao-Dong & Wang, Yuan-Jing & Gao, Yuan-Wen, 2017. "Numerical simulation of thermoelectric performance of linear-shaped thermoelectric generators under transient heat supply," Energy, Elsevier, vol. 130(C), pages 276-285.
    14. Twaha, Ssennoga & Zhu, Jie & Yan, Yuying & Li, Bo, 2016. "A comprehensive review of thermoelectric technology: Materials, applications, modelling and performance improvement," Renewable and Sustainable Energy Reviews, Elsevier, vol. 65(C), pages 698-726.
    15. Jang, Eunhwa & Banerjee, Priyanshu & Huang, Jiyuan & Madan, Deepa, 2021. "High performance scalable and cost-effective thermoelectric devices fabricated using energy efficient methods and naturally occuring materials," Applied Energy, Elsevier, vol. 294(C).
    16. Siddique, Abu Raihan Mohammad & Rabari, Ronil & Mahmud, Shohel & Heyst, Bill Van, 2016. "Thermal energy harvesting from the human body using flexible thermoelectric generator (FTEG) fabricated by a dispenser printing technique," Energy, Elsevier, vol. 115(P1), pages 1081-1091.
    17. Liu, Kai & Tang, Xiaobin & Liu, Yunpeng & Xu, Zhiheng & Yuan, Zicheng & Zhang, Zhengrong, 2020. "Enhancing the performance of fully-scaled structure-adjustable 3D thermoelectric devices based on cold–press sintering and molding," Energy, Elsevier, vol. 206(C).
    18. Cai, Yang & Zhang, Dong-Dong & Liu, Di & Zhao, Fu-Yun & Wang, Han-Qing, 2019. "Air source thermoelectric heat pump for simultaneous cold air delivery and hot water supply: Full modeling and performance evaluation," Renewable Energy, Elsevier, vol. 130(C), pages 968-981.
    19. Vaithinathan Karthikeyan & James Utama Surjadi & Xiaocui Li & Rong Fan & Vaskuri C. S. Theja & Wen Jung Li & Yang Lu & Vellaisamy A. L. Roy, 2023. "Three dimensional architected thermoelectric devices with high toughness and power conversion efficiency," Nature Communications, Nature, vol. 14(1), pages 1-10, December.
    20. Zeb, K. & Ali, S.M. & Khan, B. & Mehmood, C.A. & Tareen, N. & Din, W. & Farid, U. & Haider, A., 2017. "A survey on waste heat recovery: Electric power generation and potential prospects within Pakistan," Renewable and Sustainable Energy Reviews, Elsevier, vol. 75(C), pages 1142-1155.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:energy:v:195:y:2020:i:c:s0360544219325873. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.journals.elsevier.com/energy .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.