IDEAS home Printed from https://ideas.repec.org/a/eee/appene/v238y2019icp1269-1298.html
   My bibliography  Save this article

Review of the state-of-the-art of particulate matter emissions from modern gasoline fueled engines

Author

Listed:
  • Qian, Yong
  • Li, Zilong
  • Yu, Liang
  • Wang, Xiaole
  • Lu, Xingcai

Abstract

Gasoline direct injection engines are widely used because of their high thermal efficiency, despite their significant high particulate emissions. Due to the potential carcinogenicity of engine particulate emissions, the new gasoline direct injection passenger vehicle emissions standards have begun to limit the particle number and/or the mass of the particulate matter emissions. To combat high particulate matter emissions, a large number of studies have been conducted worldwide to determine the most effective cause of particulate matter emissions. It was found that particulate emissions are mainly derived from the non-premixed combustion and the stratified combustion of the fuel film on the piston top surface, cylinder walls, and valve bottom surface. Thus, the fuel/air mixture preparation methods, fuel physicochemical properties, and engine operating parameters have significant effects on particulate matter emissions. In addition, the particulate matter emissions of light-duty vehicles are measured on the chassis dynamometer in various driving cycles, which implies that the driving cycles will play an important role in the testing results, even for a vehicle engine. Therefore, in terms of the recently published documents on this important topic, this paper presents a comprehensive review on the latest research progress, including the particulate matter formation mechanism of gasoline engines, effects of fuel/air mixture preparation strategies, fuel physical-chemical properties, and engine operating conditions on particulate size distribution characteristics. Furthermore, the characteristics of the particulate emissions of gasoline/alcohol blends, and the effects of the driving cycle on vehicle particulate emissions were also summarized. In addition, the characteristics of the particulate emissions of new-generation gasoline combustion modes, such as homogenous charge compression ignition combustion, reactivity control compression ignition combustion, and gasoline compression ignition combustion are preliminarily discussed, and future research directions are also discussed.

Suggested Citation

  • Qian, Yong & Li, Zilong & Yu, Liang & Wang, Xiaole & Lu, Xingcai, 2019. "Review of the state-of-the-art of particulate matter emissions from modern gasoline fueled engines," Applied Energy, Elsevier, vol. 238(C), pages 1269-1298.
    • Handle: RePEc:eee:appene:v:238:y:2019:i:c:p:1269-1298
    DOI: 10.1016/j.apenergy.2019.01.179
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0306261919301874
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.apenergy.2019.01.179?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Bogarra, M. & Herreros, J.M. & Tsolakis, A. & York, A.P.E. & Millington, P.J., 2016. "Study of particulate matter and gaseous emissions in gasoline direct injection engine using on-board exhaust gas fuel reforming," Applied Energy, Elsevier, vol. 180(C), pages 245-255.
    2. Jiang, Chenxu & Li, Zilong & Qian, Yong & Wang, Xiaole & Zhang, Yahui & Lu, Xingcai, 2018. "Influences of fuel injection strategies on combustion performance and regular/irregular emissions in a turbocharged gasoline direct injection engine: Commercial gasoline versus multi-components gasoli," Energy, Elsevier, vol. 157(C), pages 173-187.
    3. Koegl, M. & Hofbeck, B. & Will, S. & Zigan, L., 2018. "Investigation of soot formation and oxidation of ethanol and butanol fuel blends in a DISI engine at different exhaust gas recirculation rates," Applied Energy, Elsevier, vol. 209(C), pages 426-434.
    4. Qian, Yong & Yu, Liang & Li, Zilong & Zhang, Yahui & Xu, Leilei & Zhou, Qiyan & Han, Dong & Lu, Xingcai, 2018. "A new methodology for diesel surrogate fuel formulation: Bridging fuel fundamental properties and real engine combustion characteristics," Energy, Elsevier, vol. 148(C), pages 424-447.
    5. Storch, Michael & Hinrichsen, Florian & Wensing, Michael & Will, Stefan & Zigan, Lars, 2015. "The effect of ethanol blending on mixture formation, combustion and soot emission studied in an optical DISI engine," Applied Energy, Elsevier, vol. 156(C), pages 783-792.
    6. Park, Cheolwoong & Lee, Sunyoup & Yi, Uihyung, 2016. "Effects of engine operating conditions on particle emissions of lean-burn gasoline direct-injection engine," Energy, Elsevier, vol. 115(P1), pages 1148-1155.
    7. He, Liqiang & Hu, Jingnan & Zhang, Shaojun & Wu, Ye & Zhu, Rencheng & Zu, Lei & Bao, Xiaofeng & Lai, Yitu & Su, Sheng, 2018. "The impact from the direct injection and multi-port fuel injection technologies for gasoline vehicles on solid particle number and black carbon emissions," Applied Energy, Elsevier, vol. 226(C), pages 819-826.
    8. Catapano, Francesco & Sementa, Paolo & Vaglieco, Bianca Maria, 2016. "Air-fuel mixing and combustion behavior of gasoline-ethanol blends in a GDI wall-guided turbocharged multi-cylinder optical engine," Renewable Energy, Elsevier, vol. 96(PA), pages 319-332.
    9. Kim, Keunsoo & Kim, Junghwan & Oh, Seungmook & Kim, Changup & Lee, Yonggyu, 2017. "Evaluation of injection and ignition schemes for the ultra-lean combustion direct-injection LPG engine to control particulate emissions," Applied Energy, Elsevier, vol. 194(C), pages 123-135.
    10. Jiang, Changzhao & Xu, Hongming & Srivastava, Dhananjay & Ma, Xiao & Dearn, Karl & Cracknell, Roger & Krueger-Venus, Jens, 2017. "Effect of fuel injector deposit on spray characteristics, gaseous emissions and particulate matter in a gasoline direct injection engine," Applied Energy, Elsevier, vol. 203(C), pages 390-402.
    11. Esarte, Claudia & Abián, María & Millera, Ángela & Bilbao, Rafael & Alzueta, María U., 2012. "Gas and soot products formed in the pyrolysis of acetylene mixed with methanol, ethanol, isopropanol or n-butanol," Energy, Elsevier, vol. 43(1), pages 37-46.
    12. Wang, Chongming & Xu, Hongming & Herreros, Jose Martin & Wang, Jianxin & Cracknell, Roger, 2014. "Impact of fuel and injection system on particle emissions from a GDI engine," Applied Energy, Elsevier, vol. 132(C), pages 178-191.
    13. Lattimore, Thomas & Wang, Chongming & Xu, Hongming & Wyszynski, Miroslaw L. & Shuai, Shijin, 2016. "Investigation of EGR Effect on Combustion and PM Emissions in a DISI Engine," Applied Energy, Elsevier, vol. 161(C), pages 256-267.
    14. Wang, Buyu & Mosbach, Sebastian & Schmutzhard, Sebastian & Shuai, Shijin & Huang, Yaqing & Kraft, Markus, 2016. "Modelling soot formation from wall films in a gasoline direct injection engine using a detailed population balance model," Applied Energy, Elsevier, vol. 163(C), pages 154-166.
    15. Zhu, Rencheng & Hu, Jingnan & Bao, Xiaofeng & He, Liqiang & Zu, Lei, 2017. "Effects of aromatics, olefins and distillation temperatures (T50 & T90) on particle mass and number emissions from gasoline direct injection (GDI) vehicles," Energy Policy, Elsevier, vol. 101(C), pages 185-193.
    16. Cho, Jaeho & Si, Woosung & Jang, Wonwook & Jin, Dongyoung & Myung, Cha-Lee & Park, Simsoo, 2015. "Impact of intermediate ethanol blends on particulate matter emission from a spark ignition direct injection (SIDI) engine," Applied Energy, Elsevier, vol. 160(C), pages 592-602.
    17. Daniel, Ritchie & Xu, Hongming & Wang, Chongming & Richardson, Dave & Shuai, Shijin, 2013. "Gaseous and particulate matter emissions of biofuel blends in dual-injection compared to direct-injection and port injection," Applied Energy, Elsevier, vol. 105(C), pages 252-261.
    18. Bonatesta, F. & Chiappetta, E. & La Rocca, A., 2014. "Part-load particulate matter from a GDI engine and the connection with combustion characteristics," Applied Energy, Elsevier, vol. 124(C), pages 366-376.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Zhang, Wenbin & Zhang, Zhou & Ma, Xiao & Awad, Omar I. & Li, Yanfei & Shuai, Shijin & Xu, Hongming, 2020. "Impact of injector tip deposits on gasoline direct injection engine combustion, fuel economy and emissions," Applied Energy, Elsevier, vol. 262(C).
    2. Anbari Attar, Mohammadreza & Xu, Hongming, 2016. "Experimental investigation of impacts of engine hardware, operating parameters and combustion performance on particulate emissions in a DISI engine," Applied Energy, Elsevier, vol. 177(C), pages 703-715.
    3. Wang, Buyu & Mosbach, Sebastian & Schmutzhard, Sebastian & Shuai, Shijin & Huang, Yaqing & Kraft, Markus, 2016. "Modelling soot formation from wall films in a gasoline direct injection engine using a detailed population balance model," Applied Energy, Elsevier, vol. 163(C), pages 154-166.
    4. Zhang, Bin & E, Jiaqiang & Gong, Jinke & Yuan, Wenhua & Zuo, Wei & Li, Yu & Fu, Jun, 2016. "Multidisciplinary design optimization of the diesel particulate filter in the composite regeneration process," Applied Energy, Elsevier, vol. 181(C), pages 14-28.
    5. Shi, Lei & Ji, Changwei & Wang, Shuofeng & Su, Teng & Cong, Xiaoyu & Wang, Du & Tang, Chuanqi, 2019. "Effects of second injection timing on combustion characteristics of the spark ignition direct injection gasoline engines with dimethyl ether enrichment in the intake port," Energy, Elsevier, vol. 180(C), pages 10-18.
    6. Zhang, Mengzhu & Ge, Yunshan & Wang, Xin & Xu, Hongming & Tan, Jianwei & Hao, Lijun, 2021. "Effects of ethanol and aromatic compositions on regulated and unregulated emissions of E10-fuelled China-6 compliant gasoline direct injection vehicles," Renewable Energy, Elsevier, vol. 176(C), pages 322-333.
    7. Mohsin Raza & Longfei Chen & Felix Leach & Shiting Ding, 2018. "A Review of Particulate Number (PN) Emissions from Gasoline Direct Injection (GDI) Engines and Their Control Techniques," Energies, MDPI, vol. 11(6), pages 1-26, June.
    8. Costa, M. & Catapano, F. & Sementa, P. & Sorge, U. & Vaglieco, B.M., 2016. "Mixture preparation and combustion in a GDI engine under stoichiometric or lean charge: an experimental and numerical study on an optically accessible engine," Applied Energy, Elsevier, vol. 180(C), pages 86-103.
    9. Jeon, Joonho, 2020. "Spatiotemporal flame propagations, combustion and solid particle emissions from lean and stoichiometric gasoline direct injection engine operation," Energy, Elsevier, vol. 210(C).
    10. Storch, Michael & Koegl, Matthias & Altenhoff, Michael & Will, Stefan & Zigan, Lars, 2016. "Investigation of soot formation of spark-ignited ethanol-blended gasoline sprays with single- and multi-component base fuels," Applied Energy, Elsevier, vol. 181(C), pages 278-287.
    11. Jiang, Changzhao & Parker, Matthew C. & Butcher, Daniel & Spencer, Adrian & Garner, Colin P. & Helie, Jerome, 2019. "Comparison of flash boiling resistance of two injector designs and the consequences on downsized gasoline engine emissions," Applied Energy, Elsevier, vol. 254(C).
    12. Kangjin Kim & Wonyong Chung & Myungsoo Kim & Charyung Kim & Cha-Lee Myung & Simsoo Park, 2020. "Inspection of PN, CO 2 , and Regulated Gaseous Emissions Characteristics from a GDI Vehicle under Various Real-World Vehicle Test Modes," Energies, MDPI, vol. 13(10), pages 1-17, May.
    13. Slavchov, Radomir I. & Mosbach, Sebastian & Kraft, Markus & Pearson, Richard & Filip, Sorin V., 2018. "An adsorption-precipitation model for the formation of injector external deposits in internal combustion engines," Applied Energy, Elsevier, vol. 228(C), pages 1423-1438.
    14. Koegl, M. & Hofbeck, B. & Will, S. & Zigan, L., 2018. "Investigation of soot formation and oxidation of ethanol and butanol fuel blends in a DISI engine at different exhaust gas recirculation rates," Applied Energy, Elsevier, vol. 209(C), pages 426-434.
    15. Jiang, Chenxu & Li, Zilong & Qian, Yong & Wang, Xiaole & Zhang, Yahui & Lu, Xingcai, 2018. "Influences of fuel injection strategies on combustion performance and regular/irregular emissions in a turbocharged gasoline direct injection engine: Commercial gasoline versus multi-components gasoli," Energy, Elsevier, vol. 157(C), pages 173-187.
    16. Gao, Zhiming & Curran, Scott J. & Parks, James E. & Smith, David E. & Wagner, Robert M. & Daw, C. Stuart & Edwards, K. Dean & Thomas, John F., 2015. "Drive cycle simulation of high efficiency combustions on fuel economy and exhaust properties in light-duty vehicles," Applied Energy, Elsevier, vol. 157(C), pages 762-776.
    17. Yu, Shenghao & Yin, Bifeng & Bi, Qinsheng & Chen, Chen & Jia, Hekun, 2021. "Experimental and numerical investigation on inner flow and spray characteristics of elliptical GDI injectors with large aspect ratio," Energy, Elsevier, vol. 224(C).
    18. Tara Larsson & Senthil Krishnan Mahendar & Anders Christiansen-Erlandsson & Ulf Olofsson, 2021. "The Effect of Pure Oxygenated Biofuels on Efficiency and Emissions in a Gasoline Optimised DISI Engine," Energies, MDPI, vol. 14(13), pages 1-24, June.
    19. Huang, Yuhan & Surawski, Nic C. & Zhuang, Yuan & Zhou, John L. & Hong, Guang, 2021. "Dual injection: An effective and efficient technology to use renewable fuels in spark ignition engines," Renewable and Sustainable Energy Reviews, Elsevier, vol. 143(C).
    20. Salvo, Orlando de & Vaz de Almeida, Flávio G., 2019. "Influence of technologies on energy efficiency results of official Brazilian tests of vehicle energy consumption," Applied Energy, Elsevier, vol. 241(C), pages 98-112.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:appene:v:238:y:2019:i:c:p:1269-1298. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.elsevier.com/wps/find/journaldescription.cws_home/405891/description#description .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.