IDEAS home Printed from https://ideas.repec.org/a/eee/appene/v229y2018icp828-840.html
   My bibliography  Save this article

Oxy-fuel combustion in a two-pass oxygen transport reactor for fire tube boiler application

Author

Listed:
  • Mansir, Ibrahim B.
  • Ben-Mansour, Rached
  • Habib, Mohamed A.

Abstract

Application of oxy-fuel combustion carbon capture technology to power plants is currently getting special attention as one of the means of curtailing CO2 emission responsible for the current climate change. The key concept of oxy-fuel combustion technology is the use of pure oxygen, obtained via air separation technologies, for combustion instead of air. Currently, the membrane separation technology is gaining high momentum due to its flexibility for different applications. Integrating oxygen transport membrane reactors to fire tube boilers has the prospects of concurrent permeation of oxygen, in-situ combustion as well as steam generation within a confined space, thus, potential for more compact boilers. Despite the in-situ prospects of the Oxygen Transport Membrane (OTM) integration, it comes with the heat transfer design challenges due to fragile nature of the membrane as well as maintaining the required operating temperatures for optimum performance. Hence the geometry as well as the heat transfer characteristics need to be well designed and the system needs to be thoroughly investigated for optimum performance. In this study, numerical modeling of a two-pass oxygen transport membrane reactor for oxygen permeation and oxy-fuel combustion characteristics analyses for fire tube boilers application was conducted. It was found that, for the non-reactive conditions, the effects of gases inlet temperature and mass flow rates on oxygen permeation along the length of the membrane was meager within the scope of this study. The gases inlet conditions dictate the rate of oxygen permeation under reactive conditions. Also, the gases inlet temperature and mass flow rates control the amount of heat transfer to the load. The sweep gas inlet condition was more critical to the stability of the combustion reaction. The current design of the proposed OTM reactor can deliver power output in the range from 1 to 5 MWe when applied to a typical fire-tube boiler.

Suggested Citation

  • Mansir, Ibrahim B. & Ben-Mansour, Rached & Habib, Mohamed A., 2018. "Oxy-fuel combustion in a two-pass oxygen transport reactor for fire tube boiler application," Applied Energy, Elsevier, vol. 229(C), pages 828-840.
    • Handle: RePEc:eee:appene:v:229:y:2018:i:c:p:828-840
    DOI: 10.1016/j.apenergy.2018.08.057
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0306261918312121
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.apenergy.2018.08.057?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Nemitallah, Medhat A. & Habib, Mohamed A. & Salaudeen, Shakirudeen A. & Mansir, Ibrahim, 2017. "Hydrogen production, oxygen separation and syngas oxy-combustion inside a water splitting membrane reactor," Renewable Energy, Elsevier, vol. 113(C), pages 221-234.
    2. Khalil, Ahmed E.E. & Gupta, Ashwani K., 2017. "Flame fluctuations in Oxy-CO2-methane mixtures in swirl assisted distributed combustion," Applied Energy, Elsevier, vol. 204(C), pages 303-317.
    3. Mancini, N.D. & Mitsos, A., 2011. "Ion transport membrane reactors for oxy-combustion–Part II: Analysis and comparison of alternatives," Energy, Elsevier, vol. 36(8), pages 4721-4739.
    4. Hu, Yukun & Yan, Jinyue & Li, Hailong, 2012. "Effects of flue gas recycle on oxy-coal power generation systems," Applied Energy, Elsevier, vol. 97(C), pages 255-263.
    5. Mancini, N.D. & Mitsos, A., 2011. "Ion transport membrane reactors for oxy-combustion – Part I: intermediate-fidelity modeling," Energy, Elsevier, vol. 36(8), pages 4701-4720.
    6. Yin, Chungen & Yan, Jinyue, 2016. "Oxy-fuel combustion of pulverized fuels: Combustion fundamentals and modeling," Applied Energy, Elsevier, vol. 162(C), pages 742-762.
    7. Habib, Mohamed A. & Nemitallah, Medhat A., 2015. "Design of an ion transport membrane reactor for application in fire tube boilers," Energy, Elsevier, vol. 81(C), pages 787-801.
    8. Hu, Yukun & Li, Hailong & Yan, Jinyue, 2014. "Numerical investigation of heat transfer characteristics in utility boilers of oxy-coal combustion," Applied Energy, Elsevier, vol. 130(C), pages 543-551.
    9. Castillo, Renzo, 2011. "Thermodynamic analysis of a hard coal oxyfuel power plant with high temperature three-end membrane for air separation," Applied Energy, Elsevier, vol. 88(5), pages 1480-1493, May.
    10. Yang, Xin & Clements, Alastair & Szuhánszki, János & Huang, Xiaohong & Farias Moguel, Oscar & Li, Jia & Gibbins, Jon & Liu, Zhaohui & Zheng, Chuguang & Ingham, Derek & Ma, Lin & Nimmo, Bill & Pourkash, 2018. "Prediction of the radiative heat transfer in small and large scale oxy-coal furnaces," Applied Energy, Elsevier, vol. 211(C), pages 523-537.
    11. Hu, Yukun & Yan, Jinyue, 2012. "Characterization of flue gas in oxy-coal combustion processes for CO2 capture," Applied Energy, Elsevier, vol. 90(1), pages 113-121.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Bordbar, Hadi & Maximov, Alexander & Hyppänen, Timo, 2019. "Improved banded method for spectral thermal radiation in participating media with spectrally dependent wall emittance," Applied Energy, Elsevier, vol. 235(C), pages 1090-1105.
    2. Te Zhao & Chusheng Chen & Hong Ye, 2021. "CFD Simulation of Syngas Combustion in a Two-Pass Oxygen Transport Membrane Reactor for Fire Tube Boiler Application," Energies, MDPI, vol. 14(21), pages 1-15, November.
    3. Mieszko Tokarski & Rafał Buczyński, 2023. "Heat Transfer Analysis for Combustion under Low-Gradient Conditions in a Small-Scale Industrial Energy Systems," Energies, MDPI, vol. 17(1), pages 1-18, December.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Ramadan, Islam A. & Ibrahim, Abdelmaged H. & Abou-Arab, Tharwat W. & Rashwan, Sherif S. & Nemitallah, Medhat A. & Habib, Mohamed A., 2016. "Effects of oxidizer flexibility and bluff-body blockage ratio on flammability limits of diffusion flames," Applied Energy, Elsevier, vol. 178(C), pages 19-28.
    2. Guo, Junjun & Liu, Zhaohui & Hu, Fan & Li, Pengfei & Luo, Wei & Huang, Xiaohong, 2018. "A compatible configuration strategy for burner streams in a 200 MWe tangentially fired oxy-fuel combustion boiler," Applied Energy, Elsevier, vol. 220(C), pages 59-69.
    3. Habib, Mohamed A. & Imteyaz, Binash & Nemitallah, Medhat A., 2020. "Second law analysis of premixed and non-premixed oxy-fuel combustion cycles utilizing oxygen separation membranes," Applied Energy, Elsevier, vol. 259(C).
    4. Yin, Chungen & Yan, Jinyue, 2016. "Oxy-fuel combustion of pulverized fuels: Combustion fundamentals and modeling," Applied Energy, Elsevier, vol. 162(C), pages 742-762.
    5. Habib, Mohamed A. & Salaudeen, Shakirudeen A. & Nemitallah, Medhat A. & Ben-Mansour, R. & Mokheimer, Esmail M.A., 2016. "Numerical investigation of syngas oxy-combustion inside a LSCF-6428 oxygen transport membrane reactor," Energy, Elsevier, vol. 96(C), pages 654-665.
    6. Wu, Hai-bo & Xu, Ming-xin & Li, Yan-bing & Wu, Jin-hua & Shen, Jian-chong & Liao, Haiyan, 2020. "Experimental research on the process of compression and purification of CO2 in oxy-fuel combustion," Applied Energy, Elsevier, vol. 259(C).
    7. Habib, Mohamed A. & Nemitallah, Medhat A. & Ahmed, Pervez & Sharqawy, Mostafa H. & Badr, Hassan M. & Muhammad, Inam & Yaqub, Mohamed, 2015. "Experimental analysis of oxygen-methane combustion inside a gas turbine reactor under various operating conditions," Energy, Elsevier, vol. 86(C), pages 105-114.
    8. Xu, Yishu & Liu, Xiaowei & Zhou, Zijian & Sheng, Lei & Wang, Chao & Xu, Minghou, 2014. "The role of steam in silica vaporization and ultrafine particulate matter formation during wet oxy-coal combustion," Applied Energy, Elsevier, vol. 133(C), pages 144-151.
    9. Bordbar, Hadi & Maximov, Alexander & Hyppänen, Timo, 2019. "Improved banded method for spectral thermal radiation in participating media with spectrally dependent wall emittance," Applied Energy, Elsevier, vol. 235(C), pages 1090-1105.
    10. Shin, Donghwan & Kang, Sanggyu, 2018. "Numerical analysis of an ion transport membrane system for oxy–fuel combustion," Applied Energy, Elsevier, vol. 230(C), pages 875-888.
    11. Nemitallah, Medhat A. & Habib, Mohamed A. & Mezghani, K., 2015. "Experimental and numerical study of oxygen separation and oxy-combustion characteristics inside a button-cell LNO-ITM reactor," Energy, Elsevier, vol. 84(C), pages 600-611.
    12. Kotowicz, Janusz & Job, Marcin & Brzęczek, Mateusz, 2020. "Thermodynamic analysis and optimization of an oxy-combustion combined cycle power plant based on a membrane reactor equipped with a high-temperature ion transport membrane ITM," Energy, Elsevier, vol. 205(C).
    13. Meng, Wenliang & Wang, Dongliang & Zhou, Huairong & Yang, Yong & Li, Hongwei & Liao, Zuwei & Yang, Siyu & Hong, Xiaodong & Li, Guixian, 2023. "Carbon dioxide from oxy-fuel coal-fired power plant integrated green ammonia for urea synthesis: Process modeling, system analysis, and techno-economic evaluation," Energy, Elsevier, vol. 278(C).
    14. Gunasekaran, S. & Mancini, N.D. & El-Khaja, R. & Sheu, E.J. & Mitsos, A., 2014. "Solar–thermal hybridization of advanced zero emissions power cycle," Energy, Elsevier, vol. 65(C), pages 152-165.
    15. Zhang, Minkai & Guo, Yincheng, 2013. "Rate based modeling of absorption and regeneration for CO2 capture by aqueous ammonia solution," Applied Energy, Elsevier, vol. 111(C), pages 142-152.
    16. Li, Shiyuan & Xu, Mingxin & Jia, Lufei & Tan, Li & Lu, Qinggang, 2016. "Influence of operating parameters on N2O emission in O2/CO2 combustion with high oxygen concentration in circulating fluidized bed," Applied Energy, Elsevier, vol. 173(C), pages 197-209.
    17. Te Zhao & Chusheng Chen & Hong Ye, 2021. "CFD Simulation of Hydrogen Generation and Methane Combustion Inside a Water Splitting Membrane Reactor," Energies, MDPI, vol. 14(21), pages 1-17, November.
    18. Prabu, V., 2015. "Integration of in-situ CO2-oxy coal gasification with advanced power generating systems performing in a chemical looping approach of clean combustion," Applied Energy, Elsevier, vol. 140(C), pages 1-13.
    19. Chi, Chung-Cheng & Lin, Ta-Hui, 2013. "Oxy-oil combustion characteristics of an existing furnace," Applied Energy, Elsevier, vol. 102(C), pages 923-930.
    20. Chowdhury, A.S.M. Arifur & Bugarin, Luz & Badhan, Antara & Choudhuri, Ahsan & Love, Norman, 2016. "Thermodynamic analysis of a directly heated oxyfuel supercritical power system," Applied Energy, Elsevier, vol. 179(C), pages 261-271.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:appene:v:229:y:2018:i:c:p:828-840. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.elsevier.com/wps/find/journaldescription.cws_home/405891/description#description .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.