IDEAS home Printed from https://ideas.repec.org/a/eee/appene/v150y2015icp138-149.html
   My bibliography  Save this article

Effect of pulsed heat power on the thermal and electrical performances of a thermoelectric generator

Author

Listed:
  • Chen, Leisheng
  • Lee, Jaeyoung

Abstract

This paper presents a transient simulation model based on the coupling of electric conduction and heat transfer in order to (1) quantify the conversion efficiency enhancement of a thermoelectric generator (TEG) under periodic heating and (2) predict the thermal and electrical performances of a TEG. Joule heating, the Peltier effect, and the Thomson effect are included in the transient model, which is experimentally validated using a commercial bismuth-telluride-based thermoelectric device under both steady state and transient conditions. In contrast to an alternate temperature gradient (ATG), which has been adopted in previous studies and is difficult to maintain in a regular square form, pulsed input power is considered herein as an effective parameter for investigating its influence on the thermal and electrical performances of a TEG. In particular, the output power and temperature difference across a TEG under pulsed input power are compared with those under constant input power, where the time average of a pulsed heat source is equivalent to the heat flux under a constant heat source. In the case of periodic heating, a rectangular input heat flux with 10% duty cycle is applied to the TEG system, with average values of 40,000W/m2, 30,000W/m2, 20,000W/m2, and 10,000W/m2; its time period ranges from 60s to 2000s. It is found that pulsed heat power yields better results than an ATG in terms of improving the conversion efficiency under the same input power condition; specifically, a maximum efficiency enhancement of 8.6× is achieved. In addition, it is found that the ratio of the maximum input heat flux to the minimum input heat flux under periodic heating, a/b, plays an important role in improving the conversion efficiency. For a given time period and average input power, a larger a/b value leads to higher efficiency enhancement. Moreover, it is observed that the efficiency enhancement is independent of the average input power under a given a/b value and fixed time period. Finally, we show that the efficiency under steady state heating is linearly proportional to the input heat flux, and the linear coefficient is 2.05×10−7 [1/(W/m2)]; this result can facilitate the prediction of TEG performance.

Suggested Citation

  • Chen, Leisheng & Lee, Jaeyoung, 2015. "Effect of pulsed heat power on the thermal and electrical performances of a thermoelectric generator," Applied Energy, Elsevier, vol. 150(C), pages 138-149.
    • Handle: RePEc:eee:appene:v:150:y:2015:i:c:p:138-149
    DOI: 10.1016/j.apenergy.2015.04.009
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0306261915004481
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.apenergy.2015.04.009?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Hsiao, Y.Y. & Chang, W.C. & Chen, S.L., 2010. "A mathematic model of thermoelectric module with applications on waste heat recovery from automobile engine," Energy, Elsevier, vol. 35(3), pages 1447-1454.
    2. Massaguer, E. & Massaguer, A. & Montoro, L. & Gonzalez, J.R., 2014. "Development and validation of a new TRNSYS type for the simulation of thermoelectric generators," Applied Energy, Elsevier, vol. 134(C), pages 65-74.
    3. Meng, Jing-Hui & Wang, Xiao-Dong & Zhang, Xin-Xin, 2013. "Transient modeling and dynamic characteristics of thermoelectric cooler," Applied Energy, Elsevier, vol. 108(C), pages 340-348.
    4. Suter, C. & Jovanovic, Z.R. & Steinfeld, A., 2012. "A 1kWe thermoelectric stack for geothermal power generation – Modeling and geometrical optimization," Applied Energy, Elsevier, vol. 99(C), pages 379-385.
    5. Yamashita, Osamu & Odahara, Hirotaka & Ochi, Takahiro, 2009. "Energy conversion efficiency of a welded Cu/Bi-Te/Cu composite under periodically alternating temperature gradients," Applied Energy, Elsevier, vol. 86(3), pages 273-283, March.
    6. Hsu, Cheng-Ting & Huang, Gia-Yeh & Chu, Hsu-Shen & Yu, Ben & Yao, Da-Jeng, 2011. "Experiments and simulations on low-temperature waste heat harvesting system by thermoelectric power generators," Applied Energy, Elsevier, vol. 88(4), pages 1291-1297, April.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Gao, Yuanzhi & Chen, Bo & Wu, Dongxu & Dai, Zhaofeng & Wang, Changling & Zhang, Xiaosong, 2022. "Comparative study of various solar power generation systems integrated with nanofluid-flat heat pipe," Applied Energy, Elsevier, vol. 327(C).
    2. Tian, Yuanyuan & Liu, Anbang & Wang, Junli & Zhou, Yajie & Bao, Chengpeng & Xie, Huaqing & Wu, Zihua & Wang, Yuanyuan, 2021. "Optimized output electricity of thermoelectric generators by matching phase change material and thermoelectric material for intermittent heat sources," Energy, Elsevier, vol. 233(C).
    3. Wang, Z.H. & Ma, Y.J. & Tang, G.H. & Zhang, Hu & Ji, F. & Sheng, Q., 2023. "Integration of thermal insulation and thermoelectric conversion embedded with phase change materials," Energy, Elsevier, vol. 278(C).
    4. Mahmoudinezhad, S. & Cotfas, P.A. & Cotfas, D.T. & Rosendahl, L.A. & Rezania, A., 2020. "Response of thermoelectric generators to Bi2Te3 and Zn4Sb3 energy harvester materials under variant solar radiation," Renewable Energy, Elsevier, vol. 146(C), pages 2488-2498.
    5. Li, Jinghua & Fang, Jiakun & Zeng, Qing & Chen, Zhe, 2016. "Optimal operation of the integrated electrical and heating systems to accommodate the intermittent renewable sources," Applied Energy, Elsevier, vol. 167(C), pages 244-254.
    6. Merienne, R. & Lynn, J. & McSweeney, E. & O'Shaughnessy, S.M., 2019. "Thermal cycling of thermoelectric generators: The effect of heating rate," Applied Energy, Elsevier, vol. 237(C), pages 671-681.
    7. Zhu, Xingzhuang & Zuo, Zhengxing & Wang, Wei & Jia, Boru & Zhan, Tianzhuo, 2023. "Experimental research and optimization of a thermoelectric generator excited by pulsed combustion mode under limited heat dissipation for combined heat and power supply," Applied Energy, Elsevier, vol. 349(C).
    8. Shittu, Samson & Li, Guiqiang & Xuan, Qindong & Zhao, Xudong & Ma, Xiaoli & Cui, Yu, 2020. "Electrical and mechanical analysis of a segmented solar thermoelectric generator under non-uniform heat flux," Energy, Elsevier, vol. 199(C).
    9. Cai, Yeyun & Ding, Ning & Rezania, A. & Deng, Fang & Rosendahl, L. & Chen, Jie, 2023. "A multi-objective optimization in system level for thermoelectric generation system," Energy, Elsevier, vol. 281(C).
    10. Shittu, Samson & Li, Guiqiang & Zhao, Xudong & Ma, Xiaoli, 2020. "Review of thermoelectric geometry and structure optimization for performance enhancement," Applied Energy, Elsevier, vol. 268(C).
    11. Lv, Hao & Wang, Xiao-Dong & Meng, Jing-Hui & Wang, Tian-Hu & Yan, Wei-Mon, 2016. "Enhancement of maximum temperature drop across thermoelectric cooler through two-stage design and transient supercooling effect," Applied Energy, Elsevier, vol. 175(C), pages 285-292.
    12. Huang, Kuo & Yan, Yuying & Wang, Guohua & Li, Bo, 2021. "Improving transient performance of thermoelectric generator by integrating phase change material," Energy, Elsevier, vol. 219(C).
    13. Aljaghtham, Mutabe & Celik, Emrah, 2022. "Design of cascade thermoelectric generation systems with improved thermal reliability," Energy, Elsevier, vol. 243(C).
    14. Tian, Xiao-Xiao & Asaadi, Soheil & Moria, Hazim & Kaood, Amr & Pourhedayat, Samira & Jermsittiparsert, Kittisak, 2020. "Proposing tube-bundle arrangement of tubular thermoelectric module as a novel air cooler," Energy, Elsevier, vol. 208(C).
    15. Kong, Li & Yu, Jia & Zhu, Hongji & Zhu, Qingshan & Yan, Qing, 2022. "Effect of three parameters of the periodic rectangular pulsed heat flux on the electrical performance improvement to a thermoelectric generator," Energy, Elsevier, vol. 261(PA).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Kim, Shiho, 2013. "Analysis and modeling of effective temperature differences and electrical parameters of thermoelectric generators," Applied Energy, Elsevier, vol. 102(C), pages 1458-1463.
    2. Massaguer, A. & Massaguer, E. & Comamala, M. & Pujol, T. & González, J.R. & Cardenas, M.D. & Carbonell, D. & Bueno, A.J., 2018. "A method to assess the fuel economy of automotive thermoelectric generators," Applied Energy, Elsevier, vol. 222(C), pages 42-58.
    3. He, Wei & Zhang, Gan & Zhang, Xingxing & Ji, Jie & Li, Guiqiang & Zhao, Xudong, 2015. "Recent development and application of thermoelectric generator and cooler," Applied Energy, Elsevier, vol. 143(C), pages 1-25.
    4. Wang, Yuchao & Dai, Chuanshan & Wang, Shixue, 2013. "Theoretical analysis of a thermoelectric generator using exhaust gas of vehicles as heat source," Applied Energy, Elsevier, vol. 112(C), pages 1171-1180.
    5. Aljaghtham, Mutabe & Celik, Emrah, 2020. "Design optimization of oil pan thermoelectric generator to recover waste heat from internal combustion engines," Energy, Elsevier, vol. 200(C).
    6. Jia, Xiao-Dong & Wang, Yuan-Jing & Gao, Yuan-Wen, 2017. "Numerical simulation of thermoelectric performance of linear-shaped thermoelectric generators under transient heat supply," Energy, Elsevier, vol. 130(C), pages 276-285.
    7. Twaha, Ssennoga & Zhu, Jie & Yan, Yuying & Li, Bo, 2016. "A comprehensive review of thermoelectric technology: Materials, applications, modelling and performance improvement," Renewable and Sustainable Energy Reviews, Elsevier, vol. 65(C), pages 698-726.
    8. Ding, L.C. & Akbarzadeh, A. & Date, Abhijit, 2016. "Electric power generation via plate type power generation unit from solar pond using thermoelectric cells," Applied Energy, Elsevier, vol. 183(C), pages 61-76.
    9. Massaguer, A. & Massaguer, E. & Comamala, M. & Pujol, T. & Montoro, L. & Cardenas, M.D. & Carbonell, D. & Bueno, A.J., 2017. "Transient behavior under a normalized driving cycle of an automotive thermoelectric generator," Applied Energy, Elsevier, vol. 206(C), pages 1282-1296.
    10. Fanciulli, C. & Abedi, H. & Merotto, L. & Dondè, R. & De Iuliis, S. & Passaretti, F., 2018. "Portable thermoelectric power generation based on catalytic combustor for low power electronic equipment," Applied Energy, Elsevier, vol. 215(C), pages 300-308.
    11. Montecucco, Andrea & Knox, Andrew R., 2014. "Accurate simulation of thermoelectric power generating systems," Applied Energy, Elsevier, vol. 118(C), pages 166-172.
    12. Liu, Di & Zhao, Fu-Yun & Yang, Hong-Xing & Tang, Guang-Fa, 2015. "Thermoelectric mini cooler coupled with micro thermosiphon for CPU cooling system," Energy, Elsevier, vol. 83(C), pages 29-36.
    13. Wang, Ruochen & Yu, Wei & Meng, Xiangpeng, 2018. "Performance investigation and energy optimization of a thermoelectric generator for a mild hybrid vehicle," Energy, Elsevier, vol. 162(C), pages 1016-1028.
    14. Tan, Ming & Deng, Yuan & Hao, Yanming, 2014. "Improved thermoelectric performance of a film device induced by densely columnar Cu electrode," Energy, Elsevier, vol. 70(C), pages 143-148.
    15. Meng, Jing-Hui & Wang, Xiao-Dong & Zhang, Xin-Xin, 2013. "Transient modeling and dynamic characteristics of thermoelectric cooler," Applied Energy, Elsevier, vol. 108(C), pages 340-348.
    16. Hsu, Cheng-Ting & Huang, Gia-Yeh & Chu, Hsu-Shen & Yu, Ben & Yao, Da-Jeng, 2011. "An effective Seebeck coefficient obtained by experimental results of a thermoelectric generator module," Applied Energy, Elsevier, vol. 88(12), pages 5173-5179.
    17. Kim, Tae Young & Negash, Assmelash A. & Cho, Gyubaek, 2017. "Experimental study of energy utilization effectiveness of thermoelectric generator on diesel engine," Energy, Elsevier, vol. 128(C), pages 531-539.
    18. Liang, Xingyu & Sun, Xiuxiu & Tian, Hua & Shu, Gequn & Wang, Yuesen & Wang, Xu, 2014. "Comparison and parameter optimization of a two-stage thermoelectric generator using high temperature exhaust of internal combustion engine," Applied Energy, Elsevier, vol. 130(C), pages 190-199.
    19. Zhao, Yulong & Wang, Shixue & Ge, Minghui & Liang, Zhaojun & Liang, Yifan & Li, Yanzhe, 2019. "Performance investigation of an intermediate fluid thermoelectric generator for automobile exhaust waste heat recovery," Applied Energy, Elsevier, vol. 239(C), pages 425-433.
    20. Weng, Chien-Chou & Huang, Mei-Jiau, 2014. "A study of using a thermoelectric generator to harvest energy from a table lamp," Energy, Elsevier, vol. 76(C), pages 788-798.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:appene:v:150:y:2015:i:c:p:138-149. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.elsevier.com/wps/find/journaldescription.cws_home/405891/description#description .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.