IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v11y2018i2p273-d128338.html
   My bibliography  Save this article

Experimental Research on the Injection Rate of DME and Diesel Fuel in Common Rail Injection System by Using Bosch and Zeuch Methods

Author

Listed:
  • Seemoon Yang

    (Leaders in Industry-University Cooperation (LINC) of Chosun University, 309 Pilmun-daero, Dong-gu, Gwangju 61452, Korea)

  • Changhee Lee

    (Department of Mechanical and Automotive Engineering, Songwon University, Songarm-ro, Gwangju 61756, Korea)

Abstract

This study investigates a preliminary injection characterization of the injection rate and the injection quantity behavior in a high-pressure common rail injection system used in a heavy-duty engine. The injection rate meter and the injection quantity meter used in the test meter measuring systems were jointly connected under the Zeuch method measurement principles at a constant volume chamber and under the Bosch method measurement principles at a long pipe flow. The trade-off trend for the injection rate and the injection quantity was observed according to the injection pressure. As expected, fuel injection with pilot injection affected the spray quantity and the injection evolution of subsequent fuel injection without pilot injection in dimethyl ether and diesel fuel. The pressure variations in the initial injection duration (2000–6000 µs) of the main and pilot injections for diesel and DME were similar. However, after 7000 µs, the pressure of DME increased more rapidly compared to that of diesel. This finding was the result of the rapid density changes caused by the nature of compressive fluid. Therefore, the DME supply pump was expected to require a higher drive energy by approximately 20% compared to that of the diesel supply pump.

Suggested Citation

  • Seemoon Yang & Changhee Lee, 2018. "Experimental Research on the Injection Rate of DME and Diesel Fuel in Common Rail Injection System by Using Bosch and Zeuch Methods," Energies, MDPI, vol. 11(2), pages 1-11, January.
  • Handle: RePEc:gam:jeners:v:11:y:2018:i:2:p:273-:d:128338
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/11/2/273/pdf
    Download Restriction: no

    File URL: https://www.mdpi.com/1996-1073/11/2/273/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Jung, Dongwon & Iida, Norimasa, 2015. "Closed-loop control of HCCI combustion for DME using external EGR and rebreathed EGR to reduce pressure-rise rate with combustion-phasing retard," Applied Energy, Elsevier, vol. 138(C), pages 315-330.
    2. Seung Hyun Yoon & Seung Chul Han & Chang Sik Lee, 2013. "Effects of High EGR Rate on Dimethyl Ether (DME) Combustion and Pollutant Emission Characteristics in a Direct Injection Diesel Engine," Energies, MDPI, vol. 6(10), pages 1-11, October.
    3. Hanzhengnan Yu & Xingyu Liang & Gequn Shu & Xu Wang & Yuesen Wang & Hongsheng Zhang, 2016. "Experimental Investigation on Wall Film Distribution of Dimethyl Ether/Diesel Blended Fuels Formed during Spray Wall Impingement," Energies, MDPI, vol. 9(11), pages 1-17, November.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Intarat Naruemon & Long Liu & Qihao Mei & Xiuzhen Ma, 2019. "Investigation on an Injection Strategy Optimization for Diesel Engines Using a One-Dimensional Spray Model," Energies, MDPI, vol. 12(21), pages 1-19, November.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Giorgio Zamboni & Simone Moggia & Massimo Capobianco, 2017. "Effects of a Dual-Loop Exhaust Gas Recirculation System and Variable Nozzle Turbine Control on the Operating Parameters of an Automotive Diesel Engine," Energies, MDPI, vol. 10(1), pages 1-18, January.
    2. Masurier, J.-B. & Foucher, F. & Dayma, G. & Dagaut, P., 2015. "Ozone applied to the homogeneous charge compression ignition engine to control alcohol fuels combustion," Applied Energy, Elsevier, vol. 160(C), pages 566-580.
    3. Desantes, J.M. & García-Oliver, J.M. & Vera-Tudela, W. & López-Pintor, D. & Schneider, B. & Boulouchos, K., 2016. "Study of the auto-ignition phenomenon of PRFs under HCCI conditions in a RCEM by means of spectroscopy," Applied Energy, Elsevier, vol. 179(C), pages 389-400.
    4. Anca N. Iuga (Butnariu) & Vasile N. Popa & Luminița I. Popa, 2018. "Comparative Analysis of Automotive Products Regarding the Influence of Eco-Friendly Methods to Emissions’ Reduction," Energies, MDPI, vol. 12(1), pages 1-24, December.
    5. Fang, Cheng & Ouyang, Minggao & Tunestal, Per & Yang, Fuyuan & Yang, Xiaofan, 2018. "Closed-loop combustion phase control for multiple combustion modes by multiple injections in a compression ignition engine fueled by gasoline-diesel mixture," Applied Energy, Elsevier, vol. 231(C), pages 816-825.
    6. Park, Su Han & Shin, Dalho & Park, Jeonghyun, 2016. "Effect of ethanol fraction on the combustion and emission characteristics of a dimethyl ether-ethanol dual-fuel reactivity controlled compression ignition engine," Applied Energy, Elsevier, vol. 182(C), pages 243-252.
    7. Zamboni, Giorgio & Moggia, Simone & Capobianco, Massimo, 2016. "Hybrid EGR and turbocharging systems control for low NOX and fuel consumption in an automotive diesel engine," Applied Energy, Elsevier, vol. 165(C), pages 839-848.
    8. Xingyu Liang & Hongsheng Zhang & Gequn Shu & Yuesen Wang & Xiuxiu Sun & Hanzhengnan Yu & Ming Ge, 2018. "Experimental Investigation on Effect of Wall Roughness and Lubricant Film on the Adhered Fuel Film of N-Butanol-Diesel Blends after Spray Impingement," Energies, MDPI, vol. 11(6), pages 1-14, June.
    9. Calam, Alper & Solmaz, Hamit & Yılmaz, Emre & İçingür, Yakup, 2019. "Investigation of effect of compression ratio on combustion and exhaust emissions in A HCCI engine," Energy, Elsevier, vol. 168(C), pages 1208-1216.
    10. Charalambides, A.G. & Sahu, S. & Hardalupas, Y. & Taylor, A.M.K.P. & Urata, Y., 2018. "Evaluation of Homogeneous Charge Compression Ignition (HCCI) autoignition development through chemiluminescence imaging and Proper Orthogonal Decomposition," Applied Energy, Elsevier, vol. 210(C), pages 288-302.
    11. Evangelos G. Giakoumis, 2017. "Diesel and Spark Ignition Engines Emissions and After-Treatment Control: Research and Advancements," Energies, MDPI, vol. 10(11), pages 1-4, November.
    12. Rami Y. Dahham & Haiqiao Wei & Jiaying Pan, 2022. "Improving Thermal Efficiency of Internal Combustion Engines: Recent Progress and Remaining Challenges," Energies, MDPI, vol. 15(17), pages 1-60, August.
    13. Komninos, N.P. & Rakopoulos, C.D., 2016. "Heat transfer in hcci phenomenological simulation models: A review," Applied Energy, Elsevier, vol. 181(C), pages 179-209.
    14. Aydoğan, Bilal, 2020. "An experimental examination of the effects of n-hexane and n-heptane fuel blends on combustion, performance and emissions characteristics in a HCCI engine," Energy, Elsevier, vol. 192(C).
    15. Hanzhengnan Yu & Xingyu Liang & Gequn Shu & Xu Wang & Yuesen Wang & Hongsheng Zhang, 2016. "Experimental Investigation on Wall Film Distribution of Dimethyl Ether/Diesel Blended Fuels Formed during Spray Wall Impingement," Energies, MDPI, vol. 9(11), pages 1-17, November.
    16. Hunicz, Jacek & Mikulski, Maciej, 2018. "Investigation of the thermal effects of fuel injection into retained residuals in HCCI engine," Applied Energy, Elsevier, vol. 228(C), pages 1966-1984.
    17. Wei Wang & Dong Liu & Yaoyao Ying & Guannan Liu & Ye Wu, 2017. "On the Response of Nascent Soot Nanostructure and Oxidative Reactivity to Photoflash Exposure," Energies, MDPI, vol. 10(7), pages 1-11, July.
    18. Hunicz, Jacek & Mikulski, Maciej & Geca, Michal S. & Rybak, Arkadiusz, 2020. "An applicable approach to mitigate pressure rise rate in an HCCI engine with negative valve overlap," Applied Energy, Elsevier, vol. 257(C).
    19. Khandal, S.V. & Banapurmath, N.R. & Gaitonde, V.N. & Hiremath, S.S., 2017. "Paradigm shift from mechanical direct injection diesel engines to advanced injection strategies of diesel homogeneous charge compression ignition (HCCI) engines- A comprehensive review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 70(C), pages 369-384.
    20. Wang, Yang & Wei, Lixia & Yao, Mingfa, 2016. "A theoretical investigation of the effects of the low-temperature reforming products on the combustion of n-heptane in an HCCI engine and a constant volume vessel," Applied Energy, Elsevier, vol. 181(C), pages 132-139.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:11:y:2018:i:2:p:273-:d:128338. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.