IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v17y2024i7p1707-d1369276.html
   My bibliography  Save this article

Numerical Study on Prediction of Icing Phenomena in Fresh Air and Blow-by Gas Mixing Region of Diesel Engine under High Velocity of Intake Air Condition

Author

Listed:
  • Wonjun Yoon

    (Graduate School, Department of Mechanical Engineering, Chosun University, Gwangju 61452, Republic of Korea)

  • Jeong-Won Lee

    (Department of Mechanical Engineering, Chosun University, Gwangju 61452, Republic of Korea)

  • Jungsoo Park

    (Department of Mechanical Engineering, Chosun University, Gwangju 61452, Republic of Korea)

Abstract

The icing of an intake pipe that might happen in an actual vehicle was numerically predicted in this study. For various operating conditions, the amount of icing was estimated, and the variables influencing the amount of icing were identified. We compared the factors that affected icing: relative humidity, air temperature, and inlet velocity. Seven RPM and load conditions, an intake temperature range of 253–268 K, and a relative humidity range of 65–85% were used for the case studies. To verify the model accuracy, wind tunnel test results from chassis dynometer tests were compared to the data from simulations. The flow analysis was performed using the numerical analytical tool ANSYS Fluent (2019 R1), while the amount of condensed water and icing was predicted using FENSAP-ICE, a program that analyzes and predicts icing phenomena under mechanical systems. The ambient temperature, relative humidity, and inlet air velocity had the biggest effects on the icing rate. The total amount of icing increased for similar BB and input air velocities. When the input air and BB velocities are the same, the variables influencing icing are the ambient temperature and relative humidity. The amount of ice was less affected by outside temperature and relative humidity when the rpm was high, and the inlet air velocity also had an impact.

Suggested Citation

  • Wonjun Yoon & Jeong-Won Lee & Jungsoo Park, 2024. "Numerical Study on Prediction of Icing Phenomena in Fresh Air and Blow-by Gas Mixing Region of Diesel Engine under High Velocity of Intake Air Condition," Energies, MDPI, vol. 17(7), pages 1-15, April.
    • Handle: RePEc:gam:jeners:v:17:y:2024:i:7:p:1707-:d:1369276
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/17/7/1707/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/17/7/1707/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Rakopoulos, C.D. & Kosmadakis, G.M. & Dimaratos, A.M. & Pariotis, E.G., 2011. "Investigating the effect of crevice flow on internal combustion engines using a new simple crevice model implemented in a CFD code," Applied Energy, Elsevier, vol. 88(1), pages 111-126, January.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Bari, S. & Saad, Idris, 2014. "Effect of guide vane height on the performance and emissions of a compression ignition (CI) engine run with biodiesel through simulation and experiment," Applied Energy, Elsevier, vol. 136(C), pages 431-444.
    2. Krishna, Addepalli S. & Mallikarjuna, J.M. & Kumar, Davinder, 2016. "Effect of engine parameters on in-cylinder flows in a two-stroke gasoline direct injection engine," Applied Energy, Elsevier, vol. 176(C), pages 282-294.
    3. Shen, Zhaojie & Wang, Xinyan & Zhao, Hua & Lin, Bo & Shen, Yitao & Yang, Jianguo, 2021. "Numerical investigation of natural gas-diesel dual-fuel engine with different piston geometries and radial clearances," Energy, Elsevier, vol. 220(C).
    4. Irimescu, Adrian, 2012. "Performance and fuel conversion efficiency of a spark ignition engine fueled with iso-butanol," Applied Energy, Elsevier, vol. 96(C), pages 477-483.
    5. Gnana Sagaya Raj, Antony Raj & Mallikarjuna, Jawali Maharudrappa & Ganesan, Venkitachalam, 2013. "Energy efficient piston configuration for effective air motion – A CFD study," Applied Energy, Elsevier, vol. 102(C), pages 347-354.
    6. Curto-Risso, P.L. & Medina, A. & Calvo Hernández, A. & Guzmán-Vargas, L. & Angulo-Brown, F., 2011. "On cycle-to-cycle heat release variations in a simulated spark ignition heat engine," Applied Energy, Elsevier, vol. 88(5), pages 1557-1567, May.
    7. Fukang Ma & Changlu Zhao & Fujun Zhang & Zhenfeng Zhao & Shuanlu Zhang, 2015. "Effects of Scavenging System Configuration on In-Cylinder Air Flow Organization of an Opposed-Piston Two-Stroke Engine," Energies, MDPI, vol. 8(6), pages 1-19, June.
    8. Kim, Joonsuk & Chun, Kwang Min & Song, Soonho & Baek, Hong-Kil & Lee, Seung Woo, 2018. "Hydrogen effects on the combustion stability, performance and emissions of a turbo gasoline direct injection engine in various air/fuel ratios," Applied Energy, Elsevier, vol. 228(C), pages 1353-1361.
    9. Payri, F. & Olmeda, P. & Martín, J. & García, A., 2011. "A complete 0D thermodynamic predictive model for direct injection diesel engines," Applied Energy, Elsevier, vol. 88(12), pages 4632-4641.
    10. Simpson, Michael C. & Chatzopoulou, Maria Anna & Oyewunmi, Oyeniyi A. & Le Brun, Niccolo & Sapin, Paul & Markides, Christos N., 2019. "Technoeconomic analysis of internal combustion engine – organic Rankine cycle systems for combined heat and power in energy-intensive buildings," Applied Energy, Elsevier, vol. 253(C), pages 1-1.
    11. Chatzopoulou, Maria Anna & Markides, Christos N., 2018. "Thermodynamic optimisation of a high-electrical efficiency integrated internal combustion engine – Organic Rankine cycle combined heat and power system," Applied Energy, Elsevier, vol. 226(C), pages 1229-1251.
    12. George M. Kosmadakis & Constantine D. Rakopoulos, 2019. "A Fast CFD-Based Methodology for Determining the Cyclic Variability and Its Effects on Performance and Emissions of Spark-Ignition Engines," Energies, MDPI, vol. 12(21), pages 1-15, October.
    13. Mohamed Ismail, Harun & Ng, Hoon Kiat & Gan, Suyin, 2012. "Evaluation of non-premixed combustion and fuel spray models for in-cylinder diesel engine simulation," Applied Energy, Elsevier, vol. 90(1), pages 271-279.
    14. Tan, Shin Mei & Ng, Hoon Kiat & Gan, Suyin, 2013. "Computational study of crevice soot entrainment in a diesel engine," Applied Energy, Elsevier, vol. 102(C), pages 898-907.
    15. Salvi, B.L. & Subramanian, K.A., 2015. "Experimental investigation and phenomenological model development of flame kernel growth rate in a gasoline fuelled spark ignition engine," Applied Energy, Elsevier, vol. 139(C), pages 93-103.
    16. Kan, Xiang & Zhou, Dezhi & Yang, Wenming & Zhai, Xiaoqiang & Wang, Chi-Hwa, 2018. "An investigation on utilization of biogas and syngas produced from biomass waste in premixed spark ignition engine," Applied Energy, Elsevier, vol. 212(C), pages 210-222.
    17. Nikolaos Diangelakis & Christos Panos & Efstratios Pistikopoulos, 2014. "Design optimization of an internal combustion engine powered CHP system for residential scale application," Computational Management Science, Springer, vol. 11(3), pages 237-266, July.
    18. Liu, Kaimin & Li, Yangtao & Yang, Jing & Deng, Banglin & Feng, Renhua & Huang, Yanjun, 2018. "Comprehensive study of key operating parameters on combustion characteristics of butanol-gasoline blends in a high speed SI engine," Applied Energy, Elsevier, vol. 212(C), pages 13-32.
    19. Chalet, David & Mahe, Alexandre & Migaud, Jérôme & Hetet, Jean-François, 2011. "A frequency modelling of the pressure waves in the inlet manifold of internal combustion engine," Applied Energy, Elsevier, vol. 88(9), pages 2988-2994.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:17:y:2024:i:7:p:1707-:d:1369276. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.