IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v17y2024i12p3042-d1418659.html
   My bibliography  Save this article

Optimization of Flywheel Rotor Energy and Stability Using Finite Element Modelling

Author

Listed:
  • Daniel Coppede

    (PPG-ENE, Universidade Federal do ABC, Santo Andre 09280560, Brazil)

  • Fabio da Silva Bortoli

    (Instituto Federal de Sao Paulo, Sao Paulo 01109010, Brazil)

  • Joao Manoel Losada Moreira

    (PPG-ENE, Universidade Federal do ABC, Santo Andre 09280560, Brazil)

  • Nadja Simao Magalhaes

    (Physics Department, Universidade Federal de Sao Paulo, Diadema 09913030, Brazil)

  • Carlos Frajuca

    (Instituto Federal de Sao Paulo, Sao Paulo 01109010, Brazil
    Instituto de Matematica, Estatistica e Fisica, Universidade Federal de Rio Grande, Rio Grande 96203900, Brazil)

Abstract

An investigation on a flywheel is presented based on finite element modelling simulations for different geometries. The goal was to optimise the energy density (rotational energy-to-mass ratio) and, at the same time, the rotational energy of a flywheel rotor. The stress behaviour of flywheel rotors under the rotational speed at the maximum stress achievable by the flywheel was analysed. Under this condition, the energy density was obtained for the different geometries, as well as the rotational energy. The best energy density performance due to geometry was achieved with a flywheel rotor presenting a new Gaussian section, which is different from the known Laval disk shape. The best results using a single disk involved a rotational speed of nearly 279,000 rpm and a rotational energy density around 1584 kJ/kg (440 Wh/kg). These values still yielded low total energy; to increase its value, two or three rotors were added to the flywheel, which were analysed in regard to stability. In particular, the triple rotor energy density was ≈ 1550 kJ/kg (431 Wh/kg). As some instability was found in these rotors, a solution using reinforcement was developed to avoid such instabilities. The energy density of such a reinforced double rotor neared 1451 kJ/kg (403 Wh/kg), and the system achieved higher total energy. The material assumed for the devices was carbon fibre Hexcel UHM 12,000, a material kept constant throughout the simulations to allow comparison among the different geometries.

Suggested Citation

  • Daniel Coppede & Fabio da Silva Bortoli & Joao Manoel Losada Moreira & Nadja Simao Magalhaes & Carlos Frajuca, 2024. "Optimization of Flywheel Rotor Energy and Stability Using Finite Element Modelling," Energies, MDPI, vol. 17(12), pages 1-24, June.
  • Handle: RePEc:gam:jeners:v:17:y:2024:i:12:p:3042-:d:1418659
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/17/12/3042/pdf
    Download Restriction: no

    File URL: https://www.mdpi.com/1996-1073/17/12/3042/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Okou, R. & Sebitosi, A.B. & Pillay, P., 2011. "Flywheel rotor manufacture for rural energy storage in sub-Saharan Africa," Energy, Elsevier, vol. 36(10), pages 6138-6145.
    2. El Bakkari, Fatima & Mounir, Hamid, 2024. "Compatible alternative energy storage systems for electric vehicles: Review of relevant technology derived from conventional systems," Energy, Elsevier, vol. 288(C).
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Rupp, A. & Baier, H. & Mertiny, P. & Secanell, M., 2016. "Analysis of a flywheel energy storage system for light rail transit," Energy, Elsevier, vol. 107(C), pages 625-638.
    2. Pavković, D. & Hoić, M. & Deur, J. & Petrić, J., 2014. "Energy storage systems sizing study for a high-altitude wind energy application," Energy, Elsevier, vol. 76(C), pages 91-103.
    3. Abdul Ghani Olabi & Tabbi Wilberforce & Mohammad Ali Abdelkareem & Mohamad Ramadan, 2021. "Critical Review of Flywheel Energy Storage System," Energies, MDPI, vol. 14(8), pages 1-33, April.
    4. Ma, Yuxuan & Sun, Xiepeng & Guo, Zhengda & Gu, Yan & Fujita, Osamu & Hu, Longhua, 2025. "Flame extinction over electrical wires under transverse flow: Critical damkohler number analysis incorporating solid-phase heat conduction," Energy, Elsevier, vol. 315(C).
    5. Armstrong, P. & Ager, D. & Thompson, I. & McCulloch, M., 2014. "Improving the energy storage capability of hot water tanks through wall material specification," Energy, Elsevier, vol. 78(C), pages 128-140.
    6. Emilia M. Szumska, 2025. "Regenerative Braking Systems in Electric Vehicles: A Comprehensive Review of Design, Control Strategies, and Efficiency Challenges," Energies, MDPI, vol. 18(10), pages 1-22, May.
    7. József Kádár & Omad (Hassan) Abdelshakour & Tali Zohar & Tareq Abu Hamed, 2024. "Feasibility Assessment of a Small-Scale Agrivoltaics-Based Desalination Plant with Flywheel Energy Storage—Case Study: Namibia," Sustainability, MDPI, vol. 16(9), pages 1-21, April.
    8. Eklas Hossain & Hossain Mansur Resalat Faruque & Md. Samiul Haque Sunny & Naeem Mohammad & Nafiu Nawar, 2020. "A Comprehensive Review on Energy Storage Systems: Types, Comparison, Current Scenario, Applications, Barriers, and Potential Solutions, Policies, and Future Prospects," Energies, MDPI, vol. 13(14), pages 1-127, July.
    9. Javed, Muhammad Shahzad & Ma, Tao & Jurasz, Jakub & Amin, Muhammad Yasir, 2020. "Solar and wind power generation systems with pumped hydro storage: Review and future perspectives," Renewable Energy, Elsevier, vol. 148(C), pages 176-192.
    10. Koohi-Kamali, Sam & Tyagi, V.V. & Rahim, N.A. & Panwar, N.L. & Mokhlis, H., 2013. "Emergence of energy storage technologies as the solution for reliable operation of smart power systems: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 25(C), pages 135-165.
    11. Ma, Tao & Yang, Hongxing & Lu, Lin & Peng, Jinqing, 2015. "Pumped storage-based standalone photovoltaic power generation system: Modeling and techno-economic optimization," Applied Energy, Elsevier, vol. 137(C), pages 649-659.

    More about this item

    Keywords

    ;
    ;
    ;
    ;

    Statistics

    Access and download statistics

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:17:y:2024:i:12:p:3042-:d:1418659. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.