IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v16y2023i3p1382-d1051601.html
   My bibliography  Save this article

Synthesis of (Cu,Mn,Co) 3 O 4 Spinel: Effects of Citrate-to-Nitrate Ratio on Its Homogeneity and Electrical Properties

Author

Listed:
  • Joelle C. W. Mah

    (Fuel Cell Institute, Universiti Kebangsaan Malaysia, Bangi 43600, Selangor Darul Ehsan, Malaysia)

  • Isyraf Aznam

    (Fuel Cell Institute, Universiti Kebangsaan Malaysia, Bangi 43600, Selangor Darul Ehsan, Malaysia
    Material Sciences Division, Gaia Science (M) Sdn Bhd, Puchong 47100, Selangor Darul Ehsan, Malaysia)

  • Andanastuti Muchtar

    (Fuel Cell Institute, Universiti Kebangsaan Malaysia, Bangi 43600, Selangor Darul Ehsan, Malaysia
    Department of Mechanical and Manufacturing Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia, Bangi 43600, Selangor Darul Ehsan, Malaysia)

  • Mahendra Rao Somalu

    (Fuel Cell Institute, Universiti Kebangsaan Malaysia, Bangi 43600, Selangor Darul Ehsan, Malaysia)

  • Jarot Raharjo

    (Research Center for Advanced Materials, National Research and Innovation Agency, Puspiptek, South Tangerang 15314, Banten, Indonesia)

Abstract

The (Cu,Mn,Co) 3 O 4 (CMC) spinel layer is useful in inhibiting Cr vaporization that deteriorates the solid oxide fuel cell performance. The effectiveness of the spinel layer in suppressing volatile Cr species from the metallic interconnects is strongly dependent on layer density, which is influenced by particle size distributions and agglomerations of the spinel powders. Considering that the material properties were influenced by the synthesizing conditions, this study elucidated the influences of citric acid (fuel) on the structure, morphology, and electrical properties of sol–gel derived CMC spinel powders. Dual-phase CMC spinel powders, consisting of cubic CuMnCoO and tetragonal Mn 2 CoO 4 , were successfully synthesized at citrate-to-nitrate (CA/MN) ratios of 0.8, 1.0, and 1.2. An undesired CuCo 2 O 4 phase was observed in spinel powders synthesized at a low CA/MN ratio of 0.5. The CA/MN ratio has influenced not only the phase formation of CMC spinel, but also the particle size distributions. The CA/MN ratio of 1.0 yielded the finest CMC spinel with the least agglomerates, which then produced the highest electrical conductivity of 116 Scm −1 . Therefore, the CA/MN ratio of 1.0 was recommended for the synthesis of CMC spinel, which can be used in fabricating the protective coating of solid oxide fuel cell interconnects.

Suggested Citation

  • Joelle C. W. Mah & Isyraf Aznam & Andanastuti Muchtar & Mahendra Rao Somalu & Jarot Raharjo, 2023. "Synthesis of (Cu,Mn,Co) 3 O 4 Spinel: Effects of Citrate-to-Nitrate Ratio on Its Homogeneity and Electrical Properties," Energies, MDPI, vol. 16(3), pages 1-11, January.
    • Handle: RePEc:gam:jeners:v:16:y:2023:i:3:p:1382-:d:1051601
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/16/3/1382/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/16/3/1382/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Mahmud, L.S. & Muchtar, A. & Somalu, M.R., 2017. "Challenges in fabricating planar solid oxide fuel cells: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 72(C), pages 105-116.
    2. Zhou, Lingfeng & Mason, Jerry H. & Li, Wenyuan & Liu, Xingbo, 2020. "Comprehensive review of chromium deposition and poisoning of solid oxide fuel cells (SOFCs) cathode materials," Renewable and Sustainable Energy Reviews, Elsevier, vol. 134(C).
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Ferreira, Victor J. & Wolff, Deidre & Hornés, Aitor & Morata, Alex & Torrell, M. & Tarancón, Albert & Corchero, Cristina, 2021. "5 kW SOFC stack via 3D printing manufacturing: An evaluation of potential environmental benefits," Applied Energy, Elsevier, vol. 291(C).
    2. AlZahrani, Abdullah A. & Dincer, Ibrahim, 2022. "Assessment of a thin-electrolyte solid oxide cell for hydrogen production," Energy, Elsevier, vol. 243(C).
    3. Whiston, Michael M. & Lima Azevedo, Inês M. & Litster, Shawn & Samaras, Constantine & Whitefoot, Kate S. & Whitacre, Jay F., 2021. "Paths to market for stationary solid oxide fuel cells: Expert elicitation and a cost of electricity model," Applied Energy, Elsevier, vol. 304(C).
    4. Lithnes Kalaivani Palniandy & Li Wan Yoon & Wai Yin Wong & Siek-Ting Yong & Ming Meng Pang, 2019. "Application of Biochar Derived from Different Types of Biomass and Treatment Methods as a Fuel Source for Direct Carbon Fuel Cells," Energies, MDPI, vol. 12(13), pages 1-15, June.
    5. Abdelkareem, Mohammad Ali & Tanveer, Waqas Hassan & Sayed, Enas Taha & Assad, M. El Haj & Allagui, Anis & Cha, S.W., 2019. "On the technical challenges affecting the performance of direct internal reforming biogas solid oxide fuel cells," Renewable and Sustainable Energy Reviews, Elsevier, vol. 101(C), pages 361-375.
    6. Mohsen Fallah Vostakola & Bahman Amini Horri, 2021. "Progress in Material Development for Low-Temperature Solid Oxide Fuel Cells: A Review," Energies, MDPI, vol. 14(5), pages 1-53, February.
    7. Orlando Corigliano & Leonardo Pagnotta & Petronilla Fragiacomo, 2022. "On the Technology of Solid Oxide Fuel Cell (SOFC) Energy Systems for Stationary Power Generation: A Review," Sustainability, MDPI, vol. 14(22), pages 1-73, November.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:16:y:2023:i:3:p:1382-:d:1051601. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.