IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v15y2022i13p4677-d848121.html
   My bibliography  Save this article

Construction and Calibration of a Unique Hot Box Apparatus

Author

Listed:
  • Abdalhadi Alhawari

    (Department of Mechanical Engineering, University of Victoria, Victoria, BC V8P 3E6, Canada
    Department of Mechanical Engineering, University of Tripoli, Tripoli 13275, Libya)

  • Phalguni Mukhopadhyaya

    (Department of Civil Engineering, University of Victoria, Victoria, BC V8P 3E6, Canada)

Abstract

A variety of mathematical models are available to estimate the thermal performance of buildings. Nevertheless, mathematical models predict the thermal performance of buildings that might differ from the actual performance. The hot box is a widely-used test apparatus to assess the actual thermal performance of various building envelope components (walls, roofs, windows) in the laboratory. This paper presents the process of designing, constructing, and calibrating a unique small-scale hot box apparatus. Despite its smaller metering area (1.0 m × 1.0 m), this apparatus met the key requirements (below ±0.25 °C fluctuations in chambers’ air temperature, and below 2.0% variation from the point-to-point temperature in reference to the temperature difference across the specimen) as prescribed in the ASTM C1363 and ISO 8990 standards. The walls of this apparatus are uniquely constructed using vacuum insulation panels or VIPs. The efficient and novel use of VIPs and workmanship during the construction of the apparatus are demonstrated through the temperature stability within the chambers. The achieved range of temperature steadiness below ±0.05 °C and point-to-point temperature variation below 1.0% of the temperature difference across the specimen allow for this apparatus to be considered unique among the calibrated hot box categories reported in the literature. In addition, having an affordable, simple-to-operate, and high-accuracy facility offers a great opportunity for researchers and practitioners to investigate new ideas and solutions. The apparatus was calibrated using two extruded polystyrene foam (XPS) specimens with thicknesses of 2″ and 4″. The calibration exercise indicates small differences between results obtained numerically, theoretically, and experimentally (below 3.0%). Ultimately, the apparatus was employed to measure the thermal properties of a specimen representing a lightweight steel framing (LSF) wall system, which is commonly used in cold climates. The results obtained experimentally were then compared to the ones estimated numerically using a 3D finite element modelling tool. The difference between the results obtained by both methods was below 9.0%.

Suggested Citation

  • Abdalhadi Alhawari & Phalguni Mukhopadhyaya, 2022. "Construction and Calibration of a Unique Hot Box Apparatus," Energies, MDPI, vol. 15(13), pages 1-20, June.
    • Handle: RePEc:gam:jeners:v:15:y:2022:i:13:p:4677-:d:848121
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/15/13/4677/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/15/13/4677/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Tullio de Rubeis & Mirco Muttillo & Iole Nardi & Leonardo Pantoli & Vincenzo Stornelli & Dario Ambrosini, 2019. "Integrated Measuring and Control System for Thermal Analysis of Buildings Components in Hot Box Experiments," Energies, MDPI, vol. 12(11), pages 1-22, May.
    2. Ricciardi, P. & Belloni, E. & Cotana, F., 2014. "Innovative panels with recycled materials: Thermal and acoustic performance and Life Cycle Assessment," Applied Energy, Elsevier, vol. 134(C), pages 150-162.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Tullio de Rubeis & Annamaria Ciccozzi & Letizia Giusti & Dario Ambrosini, 2022. "The 3D Printing Potential for Heat Flow Optimization: Influence of Block Geometries on Heat Transfer Processes," Sustainability, MDPI, vol. 14(23), pages 1-19, November.
    2. Kim, Junbeum & Guillaume, Bertrand & Chung, Jinwook & Hwang, Yongwoo, 2015. "Critical and precious materials consumption and requirement in wind energy system in the EU 27," Applied Energy, Elsevier, vol. 139(C), pages 327-334.
    3. Manuela Neri & Mariagrazia Pilotelli & Marco Traversi & Elisa Levi & Edoardo Alessio Piana & Mariasole Bannó & Eva Cuerva & Pablo Pujadas & Alfredo Guardo, 2021. "Conversion of End-of-Life Household Materials into Building Insulating Low-Cost Solutions for the Development of Vulnerable Contexts: Review and Outlook towards a Circular and Sustainable Economy," Sustainability, MDPI, vol. 13(8), pages 1-21, April.
    4. Miroslav Badida & Marek Moravec & Miriama Pinosova & Miriam Andrejiova & Kristián Pástor & Alžbeta Nováková & Tibor Dzuro, 2022. "Analysis and Research on the Use of Bulk Recycled Materials for Sound Insulation Applications," Sustainability, MDPI, vol. 14(18), pages 1-17, September.
    5. Liu, LiFang & Li, HongQiang & Lazzaretto, Andrea & Manente, Giovanni & Tong, ChunYi & Liu, QiBin & Li, NianPing, 2017. "The development history and prospects of biomass-based insulation materials for buildings," Renewable and Sustainable Energy Reviews, Elsevier, vol. 69(C), pages 912-932.
    6. Piotr Michalak, 2021. "Experimental and Theoretical Study on the Internal Convective and Radiative Heat Transfer Coefficients for a Vertical Wall in a Residential Building," Energies, MDPI, vol. 14(18), pages 1-22, September.
    7. Romina Paolucci & Marianna Rotilio & Stefano Ricci & Andrea Pelliccione & Giuseppe Ferri, 2022. "A Sensor-Based System for Dust Containment in the Construction Site," Energies, MDPI, vol. 15(19), pages 1-20, October.
    8. Moretti, Elisa & Belloni, Elisa & Agosti, Fabrizio, 2016. "Innovative mineral fiber insulation panels for buildings: Thermal and acoustic characterization," Applied Energy, Elsevier, vol. 169(C), pages 421-432.
    9. Jorge de Brito & M. Glória Gomes, 2020. "Special Issue “Building Thermal Envelope”," Energies, MDPI, vol. 13(5), pages 1-5, February.
    10. Tullio de Rubeis & Luca Evangelisti & Claudia Guattari & Domenica Paoletti & Francesco Asdrubali & Dario Ambrosini, 2022. "How Do Temperature Differences and Stable Thermal Conditions Affect the Heat Flux Meter (HFM) Measurements of Walls? Laboratory Experimental Analysis," Energies, MDPI, vol. 15(13), pages 1-12, June.
    11. Veronika Gumanová & Lýdia Sobotová & Tibor Dzuro & Miroslav Badida & Marek Moravec, 2022. "Experimental Survey of the Sound Absorption Performance of Natural Fibres in Comparison with Conventional Insulating Materials," Sustainability, MDPI, vol. 14(7), pages 1-16, April.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:15:y:2022:i:13:p:4677-:d:848121. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.