IDEAS home Printed from https://ideas.repec.org/a/eee/energy/v93y2015ip2p2292-2298.html
   My bibliography  Save this article

Optimal profile of heat transfer pin fins under technological constraints

Author

Listed:
  • Badescu, Viorel

Abstract

Direct optimal control methods are used. The pin fin's volume is minimized for given heat flux value. Schmidt's criterion is not adopted. The optimal pin fin profile is neither parabolic nor circular. It consists of two regions. In the first region, close to the basis, the pin thickness decreases linearly. In the second region the pin thickness is constant or may decrease, depending on thermal loads and operation. The optimal control solution is usually singular but may be approximated by a bang–bang solution. The Schmidt criterion works better at larger heat flux values. Results obtained for specific assumptions adopted in the paper (fluid temperature 300 K, transverse Biot number ranging between 0.00041 and 0.041) are summarized next. For very small values of the heat flux (=0.1 W) the reduced minimum pin fin volume (i.e. the ratio between pin fin volume and the volume of a cylinder of similar length) is about one tenth. The technology and design constraints have important effects on the optimal pin fin's profile. The reduced minimum pin fin volume decreases from 0.30 to 0.20 when the maximum slope of the pin fin profile increases from 1 to 100. The reduced pin fin volume is a minimum minimorum for a maximum allowable pin fin temperature ranging between two and three times the fluid temperature.

Suggested Citation

  • Badescu, Viorel, 2015. "Optimal profile of heat transfer pin fins under technological constraints," Energy, Elsevier, vol. 93(P2), pages 2292-2298.
    • Handle: RePEc:eee:energy:v:93:y:2015:i:p2:p:2292-2298
    DOI: 10.1016/j.energy.2015.10.071
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0360544215014395
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.energy.2015.10.071?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Elshafei, E.A.M., 2010. "Natural convection heat transfer from a heat sink with hollow/perforated circular pin fins," Energy, Elsevier, vol. 35(7), pages 2870-2877.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Yang, Xiaohu & Lu, Zhao & Bai, Qingsong & Zhang, Qunli & Jin, Liwen & Yan, Jinyue, 2017. "Thermal performance of a shell-and-tube latent heat thermal energy storage unit: Role of annular fins," Applied Energy, Elsevier, vol. 202(C), pages 558-570.
    2. Wang, Jin & Yu, Kai & Ye, Mingzheng & Wang, Enyu & Wang, Wei & Sundén, Bengt, 2022. "Effects of pin fins and vortex generators on thermal performance in a microchannel with Al2O3 nanofluids," Energy, Elsevier, vol. 239(PE).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Sertkaya, Ahmet Ali & Bilir, Şefik & Kargıcı, Suna, 2011. "Experimental investigation of the effects of orientation angle on heat transfer performance of pin-finned surfaces in natural convection," Energy, Elsevier, vol. 36(3), pages 1513-1517.
    2. Jang, Daeseok & Yook, Se-Jin & Lee, Kwan-Soo, 2014. "Optimum design of a radial heat sink with a fin-height profile for high-power LED lighting applications," Applied Energy, Elsevier, vol. 116(C), pages 260-268.
    3. Torabi, Mohsen & Aziz, Abdul & Zhang, Kaili, 2013. "A comparative study of longitudinal fins of rectangular, trapezoidal and concave parabolic profiles with multiple nonlinearities," Energy, Elsevier, vol. 51(C), pages 243-256.
    4. Kaluri, Ram Satish & Basak, Tanmay, 2010. "Analysis of distributed thermal management policy for energy-efficient processing of materials by natural convection," Energy, Elsevier, vol. 35(12), pages 5093-5107.
    5. Kundu, Balaram & Barman, Debasis, 2011. "An analytical prediction for performance and optimization of an annular fin assembly of trapezoidal profile under dehumidifying conditions," Energy, Elsevier, vol. 36(5), pages 2572-2588.
    6. Basak, Tanmay & Anandalakshmi, R. & Kumar, Pushpendra & Roy, S., 2012. "Entropy generation vs energy flow due to natural convection in a trapezoidal cavity with isothermal and non-isothermal hot bottom wall," Energy, Elsevier, vol. 37(1), pages 514-532.
    7. Kundu, Balaram & Lee, Kwan-Soo, 2012. "A novel analysis for calculating the smallest envelope shape of wet fins with a nonlinear mode of surface transport," Energy, Elsevier, vol. 44(1), pages 527-543.
    8. Sungjoon Byun & Seounghwan Hyeon & Kwan-Soo Lee, 2022. "Guide Vane for Thermal Enhancement of a LED Heat Sink," Energies, MDPI, vol. 15(7), pages 1-13, March.
    9. Hsiao, Kai-Long, 2013. "Energy conversion conjugate conduction–convection and radiation over non-linearly extrusion stretching sheet with physical multimedia effects," Energy, Elsevier, vol. 59(C), pages 494-502.
    10. Uddin, Md. Jashim & Bég, O. Anwar & Uddin, Md. Nazir, 2016. "Energy conversion under conjugate conduction, magneto-convection, diffusion and nonlinear radiation over a non-linearly stretching sheet with slip and multiple convective boundary conditions," Energy, Elsevier, vol. 115(P1), pages 1119-1129.
    11. Mikhailenko, Stepan A. & Sheremet, Mikhail A. & Pop, Ioan, 2020. "Natural convection combined with surface radiation in a rotating cavity with an element of variable volumetric heat generation," Energy, Elsevier, vol. 210(C).
    12. Hazarika, Saheera Azmi & Bhanja, Dipankar & Nath, Sujit & Kundu, Balaram, 2015. "Analytical solution to predict performance and optimum design parameters of a constructal T-shaped fin with simultaneous heat and mass transfer," Energy, Elsevier, vol. 84(C), pages 303-316.
    13. Kundu, Balaram & Lee, Kwan-Soo, 2012. "Analytic solution for heat transfer of wet fins on account of all nonlinearity effects," Energy, Elsevier, vol. 41(1), pages 354-367.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:energy:v:93:y:2015:i:p2:p:2292-2298. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.journals.elsevier.com/energy .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.