IDEAS home Printed from https://ideas.repec.org/a/eee/energy/v47y2012i1p543-552.html
   My bibliography  Save this article

Effect of soot accumulation in a diesel particle filter on the combustion process and gaseous emissions

Author

Listed:
  • Lapuerta, Magín
  • Rodríguez-Fernández, José
  • Oliva, Fermín

Abstract

Particulate filters are massively used in new diesel vehicles to reduce particulate emissions below the regulation limits. The setting of filters in the exhaust lines imposes various changes in the engine working conditions, including increased back-pressure, resulting in some fuel penalty. In this work, the filter loading process was investigated in a modern common-rail diesel engine equipped with diesel oxidation catalyst and diesel particulate filter. The engine was fuelled with EN-590 diesel fuel and run in a highly emissive operating mode selected among those reproducing the New European Driving Cycle. During the test the intake/exhaust conditions, intake charge, injection and combustion timing, fuel consumption and regulated emissions were measured. It was observed that the EGR (exhaust gas recirculation) ratio decreased from 30% down to 21%, shifting the combustion process away from its design parameters. In consequence, nitrogen oxides emissions increased around 60% along the test, compromising the objectives of the emission regulations. A 4% increase in fuel consumption throughout the test was measured, this value being higher than that expected from previous literature. An energy balance revealed that such penalty was caused by increased pumping losses and, especially, by higher energy losses via exhaust gas temperature and engine coolant.

Suggested Citation

  • Lapuerta, Magín & Rodríguez-Fernández, José & Oliva, Fermín, 2012. "Effect of soot accumulation in a diesel particle filter on the combustion process and gaseous emissions," Energy, Elsevier, vol. 47(1), pages 543-552.
    • Handle: RePEc:eee:energy:v:47:y:2012:i:1:p:543-552
    DOI: 10.1016/j.energy.2012.09.054
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0360544212007335
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.energy.2012.09.054?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Maiboom, Alain & Tauzia, Xavier & Hétet, Jean-François, 2008. "Experimental study of various effects of exhaust gas recirculation (EGR) on combustion and emissions of an automotive direct injection diesel engine," Energy, Elsevier, vol. 33(1), pages 22-34.
    2. Torregrosa, A.J. & Serrano, J.R. & Arnau, F.J. & Piqueras, P., 2011. "A fluid dynamic model for unsteady compressible flow in wall-flow diesel particulate filters," Energy, Elsevier, vol. 36(1), pages 671-684.
    3. Piscaglia, F. & Ferrari, G., 2009. "A novel 1D approach for the simulation of unsteady reacting flows in diesel exhaust after-treatment systems," Energy, Elsevier, vol. 34(12), pages 2051-2062.
    4. Knecht, Walter, 2008. "Diesel engine development in view of reduced emission standards," Energy, Elsevier, vol. 33(2), pages 264-271.
    5. Torregrosa, A.J. & Broatch, A. & Novella, R. & Mónico, L.F., 2011. "Suitability analysis of advanced diesel combustion concepts for emissions and noise control," Energy, Elsevier, vol. 36(2), pages 825-838.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Lapuerta, Magín & Ramos, Ángel & Barba, Javier & Fernández-Rodríguez, David, 2018. "Cold- and warm-temperature emissions assessment of n-butanol blends in a Euro 6 vehicle," Applied Energy, Elsevier, vol. 218(C), pages 173-183.
    2. Tsuneyoshi, Koji & Yamamoto, Kazuhiro, 2013. "Experimental study of hexagonal and square diesel particulate filters under controlled and uncontrolled catalyzed regeneration," Energy, Elsevier, vol. 60(C), pages 325-332.
    3. Macián, V. & Serrano, J.R. & Piqueras, P. & Sanchis, E.J., 2019. "Internal pore diffusion and adsorption impact on the soot oxidation in wall-flow particulate filters," Energy, Elsevier, vol. 179(C), pages 407-421.
    4. Rodríguez-Fernández, José & Lapuerta, Magín & Sánchez-Valdepeñas, Jesús, 2017. "Regeneration of diesel particulate filters: Effect of renewable fuels," Renewable Energy, Elsevier, vol. 104(C), pages 30-39.
    5. Seok, Jungmin & Chun, Kwang Min & Song, Soonho & Lee, Jeongmin, 2014. "An empirical study of the dry soot filtration behavior of a metal foam filter on a particle number concentration basis," Energy, Elsevier, vol. 76(C), pages 949-957.
    6. Choi, Seungmok & Oh, Kwang-Chul & Lee, Chun-Bum, 2014. "The effects of filter porosity and flow conditions on soot deposition/oxidation and pressure drop in particulate filters," Energy, Elsevier, vol. 77(C), pages 327-337.
    7. Luján, José Manuel & Bermúdez, Vicente & Piqueras, Pedro & García-Afonso, Óscar, 2015. "Experimental assessment of pre-turbo aftertreatment configurations in a single stage turbocharged diesel engine. Part 1: Steady-state operation," Energy, Elsevier, vol. 80(C), pages 599-613.
    8. Chen, Jingwei & E, Jiaqiang & Kang, Siyi & Zhao, Xiaohuan & Zhu, Hao & Deng, Yuanwang & Peng, Qingguo & Zhang, Zhiqing, 2019. "Modeling and characterization of the mass transfer and thermal mechanics of the power lithium manganate battery under charging process," Energy, Elsevier, vol. 187(C).
    9. Mwangi, John Kennedy & Lee, Wen-Jhy & Chang, Yu-Cheng & Chen, Chia-Yang & Wang, Lin-Chi, 2015. "An overview: Energy saving and pollution reduction by using green fuel blends in diesel engines," Applied Energy, Elsevier, vol. 159(C), pages 214-236.
    10. Luján, José Manuel & Serrano, José Ramón & Piqueras, Pedro & García-Afonso, Óscar, 2015. "Experimental assessment of a pre-turbo aftertreatment configuration in a single stage turbocharged diesel engine. Part 2: Transient operation," Energy, Elsevier, vol. 80(C), pages 614-627.
    11. Lapuerta, Magín & Rodríguez-Fernández, José & García-Contreras, Reyes, 2015. "Effect of a glycerol-derived advanced biofuel –FAGE (fatty acid formal glycerol ester)– on the emissions of a diesel engine tested under the New European Driving Cycle," Energy, Elsevier, vol. 93(P1), pages 568-579.
    12. Eugenio Meloni & Bruno Rossomando & Gianluigi De Falco & Mariano Sirignano & Ivan Arsie & Vincenzo Palma, 2023. "Effect of a Cu-Ferrite Catalyzed DPF on the Ultrafine Particle Emissions from a Light-Duty Diesel Engine," Energies, MDPI, vol. 16(10), pages 1-19, May.
    13. Bermúdez, Vicente & Serrano, José Ramón & Piqueras, Pedro & Campos, Daniel, 2015. "Analysis of the influence of pre-DPF water injection technique on pollutants emission," Energy, Elsevier, vol. 89(C), pages 778-792.
    14. Bermúdez, V. & Serrano, J.R. & Piqueras, P. & García-Afonso, O., 2015. "Pre-DPF water injection technique for pressure drop control in loaded wall-flow diesel particulate filters," Applied Energy, Elsevier, vol. 140(C), pages 234-245.
    15. Millo, Federico & Andreata, Maurizio & Rafigh, Mahsa & Mercuri, Davide & Pozzi, Chiara, 2015. "Impact on vehicle fuel economy of the soot loading on diesel particulate filters made of different substrate materials," Energy, Elsevier, vol. 86(C), pages 19-30.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Tsuneyoshi, Koji & Yamamoto, Kazuhiro, 2013. "Experimental study of hexagonal and square diesel particulate filters under controlled and uncontrolled catalyzed regeneration," Energy, Elsevier, vol. 60(C), pages 325-332.
    2. Tsuneyoshi, Koji & Yamamoto, Kazuhiro, 2012. "A study on the cell structure and the performances of wall-flow diesel particulate filter," Energy, Elsevier, vol. 48(1), pages 492-499.
    3. Payri, F. & Broatch, A. & Serrano, J.R. & Piqueras, P., 2011. "Experimental–theoretical methodology for determination of inertial pressure drop distribution and pore structure properties in wall-flow diesel particulate filters (DPFs)," Energy, Elsevier, vol. 36(12), pages 6731-6744.
    4. Galindo, José & Serrano, José Ramón & Piqueras, Pedro & García-Afonso, Óscar, 2012. "Heat transfer modelling in honeycomb wall-flow diesel particulate filters," Energy, Elsevier, vol. 43(1), pages 201-213.
    5. Macián, V. & Serrano, J.R. & Piqueras, P. & Sanchis, E.J., 2019. "Internal pore diffusion and adsorption impact on the soot oxidation in wall-flow particulate filters," Energy, Elsevier, vol. 179(C), pages 407-421.
    6. Jia, Ming & Li, Yaopeng & Xie, Maozhao & Wang, Tianyou, 2013. "Numerical evaluation of the potential of late intake valve closing strategy for diesel PCCI (premixed charge compression ignition) engine in a wide speed and load range," Energy, Elsevier, vol. 51(C), pages 203-215.
    7. Serrano, J. & Jiménez-Espadafor, F.J. & Lora, A. & Modesto-López, L. & Gañán-Calvo, A. & López-Serrano, J., 2019. "Experimental analysis of NOx reduction through water addition and comparison with exhaust gas recycling," Energy, Elsevier, vol. 168(C), pages 737-752.
    8. Serrano, José Ramón & Arnau, Francisco José & Piqueras, Pedro & García-Afonso, Óscar, 2013. "Packed bed of spherical particles approach for pressure drop prediction in wall-flow DPFs (diesel particulate filters) under soot loading conditions," Energy, Elsevier, vol. 58(C), pages 644-654.
    9. Benajes, Jesús & Molina, Santiago & Novella, Ricardo & Belarte, Eduardo, 2014. "Evaluation of massive exhaust gas recirculation and Miller cycle strategies for mixing-controlled low temperature combustion in a heavy duty diesel engine," Energy, Elsevier, vol. 71(C), pages 355-366.
    10. Luján, José Manuel & Bermúdez, Vicente & Piqueras, Pedro & García-Afonso, Óscar, 2015. "Experimental assessment of pre-turbo aftertreatment configurations in a single stage turbocharged diesel engine. Part 1: Steady-state operation," Energy, Elsevier, vol. 80(C), pages 599-613.
    11. Jiaqiang, E & Zhao, Xiaohuan & Xie, Longfu & Zhang, Bin & Chen, Jingwei & Zuo, Qingsong & Han, Dandan & Hu, Wenyu & Zhang, Zhiqing, 2019. "Performance enhancement of microwave assisted regeneration in a wall-flow diesel particulate filter based on field synergy theory," Energy, Elsevier, vol. 169(C), pages 719-729.
    12. Feng, Hongqing & Zheng, Zunqing & Yao, Mingfa & Cheng, Gang & Wang, Meiying & Wang, Xin, 2013. "Effects of exhaust gas recirculation on low temperature combustion using wide distillation range diesel," Energy, Elsevier, vol. 51(C), pages 291-296.
    13. Shen, Zhaojie & Liu, Zhongchang & Tian, Jing & Liu, Jiangwei, 2014. "Investigation of in-cylinder gas stratification of diesel engine during intake and compression stroke," Energy, Elsevier, vol. 72(C), pages 671-679.
    14. Zhu, Dengting & Zheng, Xinqian, 2017. "Asymmetric twin-scroll turbocharging in diesel engines for energy and emission improvement," Energy, Elsevier, vol. 141(C), pages 702-714.
    15. Xu, Guangfu & Jia, Ming & Li, Yaopeng & Xie, Maozhao & Su, Wanhua, 2017. "Multi-objective optimization of the combustion of a heavy-duty diesel engine with low temperature combustion (LTC) under a wide load range: (II) Detailed parametric, energy, and exergy analysis," Energy, Elsevier, vol. 139(C), pages 247-261.
    16. Benajes, Jesús & Novella, Ricardo & García, Antonio & Arthozoul, Simon, 2011. "The role of in-cylinder gas density and oxygen concentration on late spray mixing and soot oxidation processes," Energy, Elsevier, vol. 36(3), pages 1599-1611.
    17. Torregrosa, A.J. & Broatch, A. & Novella, R. & Mónico, L.F., 2011. "Suitability analysis of advanced diesel combustion concepts for emissions and noise control," Energy, Elsevier, vol. 36(2), pages 825-838.
    18. Arya, Pranav & Millo, Federico & Mallamo, Fabio, 2019. "A fully automated smooth calibration generation methodology for optimization of latest generation of automotive diesel engines," Energy, Elsevier, vol. 178(C), pages 334-343.
    19. S. M. Ashrafur Rahman & I. M. Rizwanul Fattah & Hwai Chyuan Ong & M. F. M. A. Zamri, 2021. "State-of-the-Art of Strategies to Reduce Exhaust Emissions from Diesel Engine Vehicles," Energies, MDPI, vol. 14(6), pages 1-24, March.
    20. Chintala, V. & Subramanian, K.A., 2015. "Experimental investigations on effect of different compression ratios on enhancement of maximum hydrogen energy share in a compression ignition engine under dual-fuel mode," Energy, Elsevier, vol. 87(C), pages 448-462.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:energy:v:47:y:2012:i:1:p:543-552. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.journals.elsevier.com/energy .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.