IDEAS home Printed from https://ideas.repec.org/a/eee/appene/v279y2020ics0306261920312988.html
   My bibliography  Save this article

A highly diluted oxy-fuel micromixer combustor with hydrogen enrichment for enhancing turndown in gas turbines

Author

Listed:
  • Hussain, Muzafar
  • Abdelhafez, Ahmed
  • Nemitallah, Medhat A.
  • Araoye, Abdulrazaq A.
  • Ben-Mansour, Rached
  • Habib, Mohamed A.

Abstract

Most burner technologies in past studies were incapable of operating at the high CO2-dilution levels required in the oxy-fuel combustors of zero-emission power cycles. The present study addresses this gap by utilizing the micromixer gas-turbine technology, coupled with hydrogen enrichment, to present an oxy-fuel burner that is capable of sustaining highly diluted flames for application in the zero-emission Allam power. Gas-turbine micromixers have never been tested under oxy-fuel combustion conditions before, which highlights the novelty of the present study. The operability window of the present burner was quantified experimentally over ranges of fuel (CH4/H2) hydrogen fraction and oxidizer (O2/CO2) oxygen fraction. It was found that the micromixer delivers superior stability, allowing for operation at oxygen fractions as low as 21% (by vol.) without hydrogen enrichment, which satisfies the nominal dilution requirements (23%) of the primary reaction zone within the Allam-cycle combustor. Micromixers are thus the technology recommended for oxy-fuel combustion in zero-emission power plants. Enriching the fuel with hydrogen was found to boost flame stability, which allowed for reducing the oxygen fraction further down to a record-low value of 13% at a hydrogen fraction of 65% (by vol.). This offers great operational flexibility and pioneering improvement in the turndown and low-load capabilities of the cycle. The results also showed that hydrogen enrichment has minimal effect on flame temperature and combustor power density (power per unit volume), which facilitates additional operational flexibility in adjusting the hydrogen fraction to sustain flame stability without influencing cycle peak temperature or turbine health.

Suggested Citation

  • Hussain, Muzafar & Abdelhafez, Ahmed & Nemitallah, Medhat A. & Araoye, Abdulrazaq A. & Ben-Mansour, Rached & Habib, Mohamed A., 2020. "A highly diluted oxy-fuel micromixer combustor with hydrogen enrichment for enhancing turndown in gas turbines," Applied Energy, Elsevier, vol. 279(C).
    • Handle: RePEc:eee:appene:v:279:y:2020:i:c:s0306261920312988
    DOI: 10.1016/j.apenergy.2020.115818
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0306261920312988
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.apenergy.2020.115818?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Oh, Jeongseog & Noh, Dongsoon & Ko, Changbok, 2013. "The effect of hydrogen addition on the flame behavior of a non-premixed oxy-methane jet in a lab-scale furnace," Energy, Elsevier, vol. 62(C), pages 362-369.
    2. Mao Li & Yiheng Tong & Marcus Thern & Jens Klingmann, 2017. "Investigation of Methane Oxy-Fuel Combustion in a Swirl-Stabilised Gas Turbine Model Combustor," Energies, MDPI, vol. 10(5), pages 1-16, May.
    3. Yin, Chungen & Yan, Jinyue, 2016. "Oxy-fuel combustion of pulverized fuels: Combustion fundamentals and modeling," Applied Energy, Elsevier, vol. 162(C), pages 742-762.
    4. Oh, Jeongseog & Noh, Dongsoon & Lee, Eungyeong, 2013. "The effect of CO addition on the flame behavior of a non-premixed oxy-methane jet in a lab-scale furnace," Applied Energy, Elsevier, vol. 112(C), pages 350-357.
    5. Rashwan, Sherif S. & Ibrahim, Abdelmaged H. & Abou-Arab, Tharwat W. & Nemitallah, Medhat A. & Habib, Mohamed A., 2016. "Experimental investigation of partially premixed methane–air and methane–oxygen flames stabilized over a perforated-plate burner," Applied Energy, Elsevier, vol. 169(C), pages 126-137.
    6. Abdelhafez, Ahmed & Rashwan, Sherif S. & Nemitallah, Medhat A. & Habib, Mohamed A., 2018. "Stability map and shape of premixed CH4/O2/CO2 flames in a model gas-turbine combustor," Applied Energy, Elsevier, vol. 215(C), pages 63-74.
    7. Habib, Mohamed A. & Nemitallah, Medhat A. & Ahmed, Pervez & Sharqawy, Mostafa H. & Badr, Hassan M. & Muhammad, Inam & Yaqub, Mohamed, 2015. "Experimental analysis of oxygen-methane combustion inside a gas turbine reactor under various operating conditions," Energy, Elsevier, vol. 86(C), pages 105-114.
    8. Nemitallah, Medhat A. & Habib, Mohamed A., 2013. "Experimental and numerical investigations of an atmospheric diffusion oxy-combustion flame in a gas turbine model combustor," Applied Energy, Elsevier, vol. 111(C), pages 401-415.
    9. Gupta, K.K. & Rehman, A. & Sarviya, R.M., 2010. "Bio-fuels for the gas turbine: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 14(9), pages 2946-2955, December.
    10. Ramadan, Islam A. & Ibrahim, Abdelmaged H. & Abou-Arab, Tharwat W. & Rashwan, Sherif S. & Nemitallah, Medhat A. & Habib, Mohamed A., 2016. "Effects of oxidizer flexibility and bluff-body blockage ratio on flammability limits of diffusion flames," Applied Energy, Elsevier, vol. 178(C), pages 19-28.
    11. Li, H. & Yan, J. & Yan, J. & Anheden, M., 2009. "Impurity impacts on the purification process in oxy-fuel combustion based CO2 capture and storage system," Applied Energy, Elsevier, vol. 86(2), pages 202-213, February.
    12. Nemitallah, Medhat A. & Imteyaz, Binash & Abdelhafez, Ahmed & Habib, Mohamed A., 2019. "Experimental and computational study on stability characteristics of hydrogen-enriched oxy-methane premixed flames," Applied Energy, Elsevier, vol. 250(C), pages 433-443.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Abdelhafez, Ahmed & Hussain, Muzafar & Nemitallah, Medhat A. & Habib, Mohamed A. & Ali, Asif, 2021. "Effects of jet diameter and spacing in a micromixer-like burner for clean oxy-fuel combustion in gas turbines," Energy, Elsevier, vol. 228(C).
    2. Chen, Xuanren & Wang, Hui & Wang, Xiangyu & Liu, Xiang & Zhu, Yuxuan, 2023. "Fuel/air mixing characteristics of a Micromix burner for hydrogen-rich gas turbine," Energy, Elsevier, vol. 282(C).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Abdelhafez, Ahmed & Rashwan, Sherif S. & Nemitallah, Medhat A. & Habib, Mohamed A., 2018. "Stability map and shape of premixed CH4/O2/CO2 flames in a model gas-turbine combustor," Applied Energy, Elsevier, vol. 215(C), pages 63-74.
    2. Ramadan, Islam A. & Ibrahim, Abdelmaged H. & Abou-Arab, Tharwat W. & Rashwan, Sherif S. & Nemitallah, Medhat A. & Habib, Mohamed A., 2016. "Effects of oxidizer flexibility and bluff-body blockage ratio on flammability limits of diffusion flames," Applied Energy, Elsevier, vol. 178(C), pages 19-28.
    3. Rashwan, Sherif S. & Ibrahim, Abdelmaged H. & Abou-Arab, Tharwat W. & Nemitallah, Medhat A. & Habib, Mohamed A., 2017. "Experimental study of atmospheric partially premixed oxy-combustion flames anchored over a perforated plate burner," Energy, Elsevier, vol. 122(C), pages 159-167.
    4. Habib, Mohamed A. & Rashwan, Sherif S. & Nemitallah, Medhat A. & Abdelhafez, Ahmed, 2017. "Stability maps of non-premixed methane flames in different oxidizing environments of a gas turbine model combustor," Applied Energy, Elsevier, vol. 189(C), pages 177-186.
    5. Zaidani, Mouna & Tajik, Abdul Raouf & Qureshi, Zahid Ahmed & Shamim, Tariq & Abu Al-Rub, Rashid K., 2018. "Investigating the flue-wall deformation effects on performance characteristics of an open-top aluminum anode baking furnace," Applied Energy, Elsevier, vol. 231(C), pages 1033-1049.
    6. Guo, Junjun & Liu, Zhaohui & Hu, Fan & Li, Pengfei & Luo, Wei & Huang, Xiaohong, 2018. "A compatible configuration strategy for burner streams in a 200 MWe tangentially fired oxy-fuel combustion boiler," Applied Energy, Elsevier, vol. 220(C), pages 59-69.
    7. Tajik, Abdul Raouf & Shamim, Tariq & Zaidani, Mouna & Abu Al-Rub, Rashid K., 2018. "The effects of flue-wall design modifications on combustion and flow characteristics of an aluminum anode baking furnace-CFD modeling," Applied Energy, Elsevier, vol. 230(C), pages 207-219.
    8. Gao, Wei & Yan, Yunfei & Shen, Kaiming & Huang, Lujing & Zhao, Ting & Gao, Bo, 2022. "Combustion characteristic of premixed H2/air in the micro cavity combustor with guide vanes," Energy, Elsevier, vol. 239(PA).
    9. Choi, Sun & Kim, Tae Young & Kim, Hee Kyung & Koo, Jaye & Kim, Jeong Soo & Kwon, Oh Chae, 2015. "Properties of inverse nonpremixed pure O2/CH4 coflow flames in a model combustor," Energy, Elsevier, vol. 93(P1), pages 1105-1115.
    10. Tu, Yaojie & Xu, Mingchen & Zhou, Dezhi & Wang, Qingxiang & Yang, Wenming & Liu, Hao, 2019. "CFD and kinetic modelling study of methane MILD combustion in O2/N2, O2/CO2 and O2/H2O atmospheres," Applied Energy, Elsevier, vol. 240(C), pages 1003-1013.
    11. Wan, Huaxian & Gao, Zihe & Ji, Jie & Zhang, Yongming & Li, Kaiyuan, 2018. "Experimental and theoretical study on flame front temperatures within ceiling jets from turbulent diffusion flames of n-heptane fuel," Energy, Elsevier, vol. 164(C), pages 79-86.
    12. Nemitallah, Medhat & Alkhaldi, Shabeeb & Abdelhafez, Ahmed & Habib, Mohamed, 2018. "Effect analysis on the macrostructure and static stability limits of oxy-methane flames in a premixed swirl combustor," Energy, Elsevier, vol. 159(C), pages 86-96.
    13. Hanak, Dawid P. & Powell, Dante & Manovic, Vasilije, 2017. "Techno-economic analysis of oxy-combustion coal-fired power plant with cryogenic oxygen storage," Applied Energy, Elsevier, vol. 191(C), pages 193-203.
    14. Odi Fawwaz Alrebei & Abdulkarem I. Amhamed & Syed Mashruk & Phil Bowen & Agustin Valera Medina, 2021. "Planar Laser-Induced Fluorescence and Chemiluminescence Analyses of CO 2 -Argon-Steam Oxyfuel (CARSOXY) Combustion," Energies, MDPI, vol. 15(1), pages 1-23, December.
    15. Rashwan, Sherif S. & Shaaban, Ahmed M. & Al-Suliman, Fahad, 2017. "A comparative study of a small-scale solar PV power plant in Saudi Arabia," Renewable and Sustainable Energy Reviews, Elsevier, vol. 80(C), pages 313-318.
    16. Choi, Sun & Lee, Seungro & Kwon, Oh Chae, 2015. "Extinction limits and structure of counterflow nonpremixed hydrogen-doped ammonia/air flames at elevated temperatures," Energy, Elsevier, vol. 85(C), pages 503-510.
    17. Habib, Mohamed A. & Imteyaz, Binash & Nemitallah, Medhat A., 2020. "Second law analysis of premixed and non-premixed oxy-fuel combustion cycles utilizing oxygen separation membranes," Applied Energy, Elsevier, vol. 259(C).
    18. Enagi, Ibrahim I. & Al-attab, K.A. & Zainal, Z.A., 2018. "Liquid biofuels utilization for gas turbines: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 90(C), pages 43-55.
    19. Rashwan, Sherif S. & Mohany, Atef & Dincer, Ibrahim, 2020. "Investigation of self-induced thermoacoustic instabilities in gas turbine combustors," Energy, Elsevier, vol. 190(C).
    20. Xu, Mingxin & Li, Shiyuan & Wu, Yinghai & Jia, Lufei & Lu, Qinggang, 2017. "The characteristics of recycled NO reduction over char during oxy-fuel fluidized bed combustion," Applied Energy, Elsevier, vol. 190(C), pages 553-562.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:appene:v:279:y:2020:i:c:s0306261920312988. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.elsevier.com/wps/find/journaldescription.cws_home/405891/description#description .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.