IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v14y2021i24p8280-d698103.html
   My bibliography  Save this article

Numerical Study on Non-Uniform Temperature Distribution and Thermal Performance of Plate Heat Exchanger

Author

Listed:
  • Jeonggyun Ham

    (Department of Mechanical Engineering, Graduate School of Chosun University, 309 Pilmundaero, Dong-gu, Gwangju 61452, Korea)

  • Gonghee Lee

    (Regulatory Assessment Department, Korea Institute of Nuclear Safety, Daejeon 34142, Korea)

  • Dong-wook Oh

    (Department of Mechanical Engineering, Graduate School of Chosun University, 309 Pilmundaero, Dong-gu, Gwangju 61452, Korea)

  • Honghyun Cho

    (Department of Mechanical Engineering, Graduate School of Chosun University, 309 Pilmundaero, Dong-gu, Gwangju 61452, Korea)

Abstract

In this study, computational fluid dynamics (CFD) analysis was performed to investigate the cause of the thermal stratification in the channel and the temperature non-uniformity of the plate heat exchanger. The flow velocity maldistribution of the channel and the merging parts caused temperature non-uniformity in the channel width direction. The non-uniformity of flow velocity and temperature in the channel is shown in Section 1 > Section 3 > Section 2 from the heat exchanger. The non-uniform temperature distribution in the channel caused channel stratification and non-uniform outlet temperature. Stratification occurred at the channel near the merging due to the flow rate non-uniformity in the channel. In particular, as the mass flow rate increased from 0.03 to 0.12 kg/s and the effectiveness increased from 0.436 to 0.615, the cold-side stratified volume decreased from 4.06 to 3.7 cm 3 , and the temperature difference between the stratified area and the outlet decreased from 1.21 K to 0.61 K. The increase in mass flow and the decrease in temperature difference between the cold and hot sides alleviated the non-uniformity of the outlet temperature due to the increase in effectiveness. Besides, as the inlet temperature difference between the cold and the hot side increases, the temperature non-uniformity at the outlet port is poor due to the increase in the stratified region at the channel, and the distance to obtain a uniform temperature in the outlet pipe increases as the temperature at the hot side increases.

Suggested Citation

  • Jeonggyun Ham & Gonghee Lee & Dong-wook Oh & Honghyun Cho, 2021. "Numerical Study on Non-Uniform Temperature Distribution and Thermal Performance of Plate Heat Exchanger," Energies, MDPI, vol. 14(24), pages 1-18, December.
    • Handle: RePEc:gam:jeners:v:14:y:2021:i:24:p:8280-:d:698103
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/14/24/8280/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/14/24/8280/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Nicolas Dinsing & Nico Schmitz & Christian Schubert & Herbert Pfeifer, 2021. "Development of an Efficient Modelling Approach for Fin-Type Heat-Exchangers in Self-Recuperative Burners," Energies, MDPI, vol. 14(21), pages 1-19, October.
    2. Myung-Ho Kim & Van Toan Nguyen & Sunghyuk Im & Yohan Jung & Sun-Rock Choi & Byoung-Jae Kim, 2021. "Experimental Validation of Flow Uniformity Improvement by a Perforated Plate in the Heat Exchanger of SFR Steam Generator," Energies, MDPI, vol. 14(18), pages 1-17, September.
    3. Arkadiusz Brenk & Pawel Pluszka & Ziemowit Malecha, 2018. "Numerical Study of Flow Maldistribution in Multi-Plate Heat Exchangers Based on Robust 2D Model," Energies, MDPI, vol. 11(11), pages 1-17, November.
    4. Wan-Ling Hu & Ai-Jun Ma & Yong Guan & Zhi-Jie Cui & Yi-Bo Zhang & Jing Wang, 2021. "Experimental Study of the Air Side Performance of Fin-and-Tube Heat Exchanger with Different Fin Material in Dehumidifying Conditions," Energies, MDPI, vol. 14(21), pages 1-15, October.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Xiang Peng & Denghong Li & Jiquan Li & Shaofei Jiang & Qilong Gao, 2020. "Improvement of Flow Distribution by New Inlet Header Configuration with Splitter Plates for Plate-Fin Heat Exchanger," Energies, MDPI, vol. 13(6), pages 1-14, March.
    2. Yu Zhai & Xu Zhao & Guanghui Xue & Zhifeng Dong, 2023. "Study on Heat Transfer Performance and Parameter Improvement of Gravity-Assisted Heat Pipe Heat Transfer Unit for Waste Heat Recovery from Mine Return Air," Energies, MDPI, vol. 16(17), pages 1-17, August.
    3. Kyung Rae Kim & Jae Keun Lee & Hae Do Jeong & Yul Ho Kang & Young Chull Ahn, 2020. "Numerical and Experimental Study of Air-to-Air Plate Heat Exchangers with Plain and Offset Strip Fin Shapes," Energies, MDPI, vol. 13(21), pages 1-13, October.
    4. Tomasz Banaszkiewicz & Maciej Chorowski & Wojciech Gizicki & Artur Jedrusyna & Jakub Kielar & Ziemowit Malecha & Agnieszka Piotrowska & Jaroslaw Polinski & Zbigniew Rogala & Korneliusz Sierpowski & Ja, 2020. "Liquefied Natural Gas in Mobile Applications—Opportunities and Challenges," Energies, MDPI, vol. 13(21), pages 1-35, October.
    5. Hyung Ju Lee & Seong Hyuk Lee, 2020. "Effect of Secondary Vortex Flow Near Contact Point on Thermal Performance in the Plate Heat Exchanger with Different Corrugation Profiles," Energies, MDPI, vol. 13(6), pages 1-13, March.
    6. Zbigniew Rogala & Arkadiusz Brenk & Ziemowit Malecha, 2019. "Theoretical and Numerical Analysis of Freezing Risk During LNG Evaporation Process," Energies, MDPI, vol. 12(8), pages 1-19, April.
    7. Maciej Chorowski & Piotr Pyrka & Zbigniew Rogala & Piotr Czupryński, 2019. "Experimental Study of Performance Improvement of 3-Bed and 2-Evaporator Adsorption Chiller by Control Optimization," Energies, MDPI, vol. 12(20), pages 1-17, October.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:14:y:2021:i:24:p:8280-:d:698103. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.