IDEAS home Printed from https://ideas.repec.org/a/eee/reensy/v215y2021ics0951832021003860.html
   My bibliography  Save this article

Component reassignment for reliability optimization of reconfigurable systems considering component degradation

Author

Listed:
  • Ma, Chenyang
  • Wang, Qiyu
  • Cai, Zhiqiang
  • Si, Shubin
  • Zhao, Jiangbin

Abstract

This paper aims to optimize the lower bound of the reconfigurable system reliability by reassigning the degrading components, which is common in practical engineering systems. First, considering the reconfigurable linear consecutive k-out-of-n (Lin/Con/k/n) system, the reliability calculation method of components and the system with reassignment are derived, respectively. Then, the Delta importance (DI) based heuristics are proposed to perform component reassignment (CR). The heuristics utilize the importance ranking based on DI, searching the most important component to be reassigned iteratively. Third, CR problem (CRP) is presented to find the optimal time and scheme of reassigning components for maximizing the lower boundary of the system reliability during the mission. To address CRP, DI-based greedy algorithms are developed. Finally, the performance of the proposed methods is demonstrated by two experiments. Experiment 1 illustrates the effectiveness and efficiency of DI-based heuristics. Experiment 2 demonstrates the effectiveness and efficiency of DI-based greedy algorithms. In three situations, the average reliability improvement using DI-based genetic algorithm-greedy (DIGA-G) is improved by 24.35%, 19.98%, 12.95%, respectively. The results show that DIGA-G can achieve higher system reliability for CRP compared with the DI-based two-stage-greedy (DITS-G) algorithm.

Suggested Citation

  • Ma, Chenyang & Wang, Qiyu & Cai, Zhiqiang & Si, Shubin & Zhao, Jiangbin, 2021. "Component reassignment for reliability optimization of reconfigurable systems considering component degradation," Reliability Engineering and System Safety, Elsevier, vol. 215(C).
    • Handle: RePEc:eee:reensy:v:215:y:2021:i:c:s0951832021003860
    DOI: 10.1016/j.ress.2021.107867
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0951832021003860
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.ress.2021.107867?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Eryilmaz, Serkan, 2018. "The number of failed components in a k-out-of-n system consisting of multiple types of components," Reliability Engineering and System Safety, Elsevier, vol. 175(C), pages 246-250.
    2. Dui, Hongyan & Si, Shubin & Yam, Richard C.M., 2017. "A cost-based integrated importance measure of system components for preventive maintenance," Reliability Engineering and System Safety, Elsevier, vol. 168(C), pages 98-104.
    3. Cai, Zhiqiang & Si, Shubin & Sun, Shudong & Li, Caitao, 2016. "Optimization of linear consecutive-k-out-of-n system with a Birnbaum importance-based genetic algorithm," Reliability Engineering and System Safety, Elsevier, vol. 152(C), pages 248-258.
    4. Ahmad Almuhtady & Seungchul Lee & Edwin Romeijn & Michael Wynblatt & Jun Ni, 2014. "A Degradation-Informed Battery-Swapping Policy for Fleets of Electric or Hybrid-Electric Vehicles," Transportation Science, INFORMS, vol. 48(4), pages 609-618, November.
    5. Qingzhu Yao & Xiaoyan Zhu & Way Kuo, 2011. "Heuristics for component assignment problems based on the Birnbaum importance," IISE Transactions, Taylor & Francis Journals, vol. 43(9), pages 633-646.
    6. Mingjian Zuo & Way Kuo, 1990. "Design and performance analysis of consecutive‐K‐out‐of‐n structure," Naval Research Logistics (NRL), John Wiley & Sons, vol. 37(2), pages 203-230, April.
    7. Dui, Hongyan & Si, Shubin & Yam, Richard C.M., 2018. "Importance measures for optimal structure in linear consecutive-k-out-of-n systems," Reliability Engineering and System Safety, Elsevier, vol. 169(C), pages 339-350.
    8. Mauricio Sánchez-Silva & Georgia-Ann Klutke, 2016. "Reliability and Life-Cycle Analysis of Deteriorating Systems," Springer Series in Reliability Engineering, Springer, number 978-3-319-20946-3, January.
    9. Fu, Yuqiang & Yuan, Tao & Zhu, Xiaoyan, 2019. "Importance-measure based methods for component reassignment problem of degrading components," Reliability Engineering and System Safety, Elsevier, vol. 190(C), pages 1-1.
    10. Si, Shubin & Levitin, Gregory & Dui, Hongyan & Sun, Shudong, 2014. "Importance analysis for reconfigurable systems," Reliability Engineering and System Safety, Elsevier, vol. 126(C), pages 72-80.
    11. Qingzhu Yao & Xiaoyan Zhu & Way Kuo, 2014. "A Birnbaum-importance based genetic local search algorithm for component assignment problems," Annals of Operations Research, Springer, vol. 212(1), pages 185-200, January.
    12. Zhao, Jiangbin & Si, Shubin & Cai, Zhiqiang, 2019. "A multi-objective reliability optimization for reconfigurable systems considering components degradation," Reliability Engineering and System Safety, Elsevier, vol. 183(C), pages 104-115.
    13. Eryilmaz, Serkan & Devrim, Yilser, 2019. "Reliability and optimal replacement policy for a k-out-of-n system subject to shocks," Reliability Engineering and System Safety, Elsevier, vol. 188(C), pages 393-397.
    14. Xiaoyan Zhu & Yuqiang Fu & Tao Yuan, 2020. "Optimum reassignment of degrading components for non-repairable systems," IISE Transactions, Taylor & Francis Journals, vol. 52(3), pages 349-361, March.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Wang, Liying & Song, Yushuang & Zhang, Wenhua & Ling, Xiaoliang, 2023. "Condition-based inspection, component reallocation and replacement optimization of two-component interchangeable series system," Reliability Engineering and System Safety, Elsevier, vol. 230(C).
    2. Qiu, Siqi & Ming, Xinguo & Sallak, Mohamed & Lu, Jialiang, 2022. "A Birnbaum importance-based two-stage approach for two-type component assignment problems," Reliability Engineering and System Safety, Elsevier, vol. 218(PA).
    3. Hongyan Dui & Huiting Xu & Yun-An Zhang, 2022. "Reliability Analysis and Redundancy Optimization of a Command Post Phased-Mission System," Mathematics, MDPI, vol. 10(22), pages 1-15, November.
    4. Liu, Mingli & Wang, Dan & Si, Shubin, 2023. "Mixed reliability importance-based solving algorithm design for the cost-constrained reliability optimization model," Reliability Engineering and System Safety, Elsevier, vol. 237(C).
    5. Li, Ruimeng & Yang, Naiding & Yi, Hao & Jin, Na, 2023. "The robustness of complex product development projects under design change risk propagation with gray attack information," Reliability Engineering and System Safety, Elsevier, vol. 235(C).
    6. Dui, Hongyan & Tian, Tianzi & Zhao, Jiangbin & Wu, Shaomin, 2022. "Comparing with the joint importance under consideration of consecutive-k-out-of-n system structure changes," Reliability Engineering and System Safety, Elsevier, vol. 219(C).
    7. Liu, Mingli & Wang, Dan & Zhao, Jiangbin & Si, Shubin, 2022. "Importance measure construction and solving algorithm oriented to the cost-constrained reliability optimization model," Reliability Engineering and System Safety, Elsevier, vol. 222(C).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Qiu, Siqi & Ming, Xinguo & Sallak, Mohamed & Lu, Jialiang, 2022. "A Birnbaum importance-based two-stage approach for two-type component assignment problems," Reliability Engineering and System Safety, Elsevier, vol. 218(PA).
    2. Wang, Dan & Si, Shubin & Cai, Zhiqiang & Zhao, Jiangbin, 2021. "Reliability optimization of linear consecutive-k-out-of-n: F systems driven by reconfigurable importance," Reliability Engineering and System Safety, Elsevier, vol. 216(C).
    3. Liu, Mingli & Wang, Dan & Zhao, Jiangbin & Si, Shubin, 2022. "Importance measure construction and solving algorithm oriented to the cost-constrained reliability optimization model," Reliability Engineering and System Safety, Elsevier, vol. 222(C).
    4. Fu, Yuqiang & Zhu, Xiaoyan & Ma, Xiaoyang, 2020. "Optimum component reallocation and system replacement maintenance for a used system with increasing minimal repair cost," Reliability Engineering and System Safety, Elsevier, vol. 204(C).
    5. Liu, Mingli & Wang, Dan & Si, Shubin, 2023. "Mixed reliability importance-based solving algorithm design for the cost-constrained reliability optimization model," Reliability Engineering and System Safety, Elsevier, vol. 237(C).
    6. Fu, Yuqiang & Zhu, Xiaoyan, 2023. "A joint age-based system replacement and component reallocation maintenance policy: Optimization, analysis and resilience," Reliability Engineering and System Safety, Elsevier, vol. 235(C).
    7. Zhu, Xiaoyan & Hao, Yaqian, 2021. "Component rearrangement and system replacement for a system with stochastic degradation processes," Reliability Engineering and System Safety, Elsevier, vol. 213(C).
    8. Zhao, Jiangbin & Si, Shubin & Cai, Zhiqiang & Guo, Peng & Zhu, Wenjin, 2020. "Mission success probability optimization for phased-mission systems with repairable component modules," Reliability Engineering and System Safety, Elsevier, vol. 195(C).
    9. Fu, Yuqiang & Yuan, Tao & Zhu, Xiaoyan, 2019. "Importance-measure based methods for component reassignment problem of degrading components," Reliability Engineering and System Safety, Elsevier, vol. 190(C), pages 1-1.
    10. Fu, Yuqiang & Wang, Jun, 2022. "Optimum periodic maintenance policy of repairable multi-component system with component reallocation and system overhaul," Reliability Engineering and System Safety, Elsevier, vol. 219(C).
    11. Qiu, Siqi & Ming, Xinguo, 2020. "An extended Birnbaum importance-based two-stage heuristic for component assignment problems under uncertainty," Reliability Engineering and System Safety, Elsevier, vol. 204(C).
    12. Dui, Hongyan & Tian, Tianzi & Zhao, Jiangbin & Wu, Shaomin, 2022. "Comparing with the joint importance under consideration of consecutive-k-out-of-n system structure changes," Reliability Engineering and System Safety, Elsevier, vol. 219(C).
    13. Cai, Zhiqiang & Si, Shubin & Sun, Shudong & Li, Caitao, 2016. "Optimization of linear consecutive-k-out-of-n system with a Birnbaum importance-based genetic algorithm," Reliability Engineering and System Safety, Elsevier, vol. 152(C), pages 248-258.
    14. Lyu, Dong & Si, Shubin, 2021. "Importance measure for K-out-of-n: G systems under dynamic random load considering strength degradation," Reliability Engineering and System Safety, Elsevier, vol. 216(C).
    15. Wang, Liying & Song, Yushuang & Zhang, Wenhua & Ling, Xiaoliang, 2023. "Condition-based inspection, component reallocation and replacement optimization of two-component interchangeable series system," Reliability Engineering and System Safety, Elsevier, vol. 230(C).
    16. Dui, Hongyan & Wu, Shaomin & Zhao, Jiangbin, 2021. "Some extensions of the component maintenance priority," Reliability Engineering and System Safety, Elsevier, vol. 214(C).
    17. Qiu, Siqi & Sallak, Mohamed & Schön, Walter & Ming, Henry X.G., 2018. "Extended LK heuristics for the optimization of linear consecutive-k-out-of-n: F systems considering parametric uncertainty and model uncertainty," Reliability Engineering and System Safety, Elsevier, vol. 175(C), pages 51-61.
    18. Chenyang Ma & Wei Wang & Zhiqiang Cai & Jiangbin Zhao, 2022. "Maintenance optimization of reconfigurable systems based on multi-objective Birnbaum importance," Journal of Risk and Reliability, , vol. 236(2), pages 277-289, April.
    19. Qingzhu Yao & Xiaoyan Zhu & Way Kuo, 2014. "A Birnbaum-importance based genetic local search algorithm for component assignment problems," Annals of Operations Research, Springer, vol. 212(1), pages 185-200, January.
    20. Chen, Liwei & Gao, Yansan & Dui, Hongyan & Xing, Liudong, 2021. "Importance measure-based maintenance optimization strategy for pod slewing system," Reliability Engineering and System Safety, Elsevier, vol. 216(C).

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:reensy:v:215:y:2021:i:c:s0951832021003860. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: https://www.journals.elsevier.com/reliability-engineering-and-system-safety .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.