IDEAS home Printed from https://ideas.repec.org/a/eee/appene/v192y2017icp422-436.html
   My bibliography  Save this article

Experimental study to distinguish the effects of methanol slip and water vapour on a high temperature PEM fuel cell at different operating conditions

Author

Listed:
  • Thomas, Sobi
  • Vang, Jakob Rabjerg
  • Araya, Samuel Simon
  • Kær, Søren Knudsen

Abstract

The objective of this paper is to separate out the effects of methanol and water vapour on a high temperature polymer electrolyte membrane fuel cell under different temperatures (160°C and 180°C) and current densities (0.2Acm−2, 0.4Acm−2 and 0.6Acm−2). The degradation rates at the different current densities and temperatures are analysed and discussed. The results are supported by IV curves and impedance spectroscopy. The individual resistance variations are extracted by equivalent circuit model fitting of the impedance spectra. The presence of water in the anode feed enhances the performance while the presence of 5% methanol tends to degrade the cell performance. However, the presence of H2O mitigates some of the adverse effects of methanol. The effect of varying fuel compositions was found to be more prominent at lower current densities. The voltage improves significantly when adding water vapour to the anode after pure hydrogen operation at 180°C. A decrease in the total resistance corresponding to the voltage improvement is observed from the impedance spectra. There is minimal variation in performance with the introduction of 3% and 5% methanol along with water vapour in the anode feed at all current densities and operating temperatures. The overall degradation over a period of 1915h is −44μVh−1. The test time includes 595h of test with pure H2 and 300h test each with 15% H2O, 3% CH3OH+15% H2O and 5% CH3OH+15% H2O at varying current densities and temperatures.

Suggested Citation

  • Thomas, Sobi & Vang, Jakob Rabjerg & Araya, Samuel Simon & Kær, Søren Knudsen, 2017. "Experimental study to distinguish the effects of methanol slip and water vapour on a high temperature PEM fuel cell at different operating conditions," Applied Energy, Elsevier, vol. 192(C), pages 422-436.
    • Handle: RePEc:eee:appene:v:192:y:2017:i:c:p:422-436
    DOI: 10.1016/j.apenergy.2016.11.063
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0306261916316488
    Download Restriction: Full text for ScienceDirect subscribers only
    File URL: https://libkey.io/10.1016/j.apenergy.2016.11.063?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Jaggi, Vikas & Jayanti, S., 2013. "A conceptual model of a high-efficiency, stand-alone power unit based on a fuel cell stack with an integrated auto-thermal ethanol reformer," Applied Energy, Elsevier, vol. 110(C), pages 295-303.
    2. Zuliani, Nicola & Taccani, Rodolfo, 2012. "Microcogeneration system based on HTPEM fuel cell fueled with natural gas: Performance analysis," Applied Energy, Elsevier, vol. 97(C), pages 802-808.
    3. Samsun, Remzi Can & Pasel, Joachim & Janßen, Holger & Lehnert, Werner & Peters, Ralf & Stolten, Detlef, 2014. "Design and test of a 5kWe high-temperature polymer electrolyte fuel cell system operated with diesel and kerosene," Applied Energy, Elsevier, vol. 114(C), pages 238-249.
    4. Najafi, Behzad & Haghighat Mamaghani, Alireza & Rinaldi, Fabio & Casalegno, Andrea, 2015. "Long-term performance analysis of an HT-PEM fuel cell based micro-CHP system: Operational strategies," Applied Energy, Elsevier, vol. 147(C), pages 582-592.
    5. Sun, Hong & Xie, Chen & Chen, Hao & Almheiri, Saif, 2015. "A numerical study on the effects of temperature and mass transfer in high temperature PEM fuel cells with ab-PBI membrane," Applied Energy, Elsevier, vol. 160(C), pages 937-944.
    6. Samuel Simon Araya & Søren Juhl Andreasen & Søren Knudsen Kær, 2012. "Experimental Characterization of the Poisoning Effects of Methanol-Based Reformate Impurities on a PBI-Based High Temperature PEM Fuel Cell," Energies, MDPI, vol. 5(11), pages 1-17, October.
    7. Jiao, Kui & Zhou, Yibo & Du, Qing & Yin, Yan & Yu, Shuhai & Li, Xianguo, 2013. "Numerical simulations of carbon monoxide poisoning in high temperature proton exchange membrane fuel cells with various flow channel designs," Applied Energy, Elsevier, vol. 104(C), pages 21-41.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Xu, Jiawei & Wu, Yuhua & Xiao, Shengying & Wang, Yifei & Xu, Xinhai, 2023. "Synergic effect investigation of carbon monoxide and other compositions on the high temperature proton exchange membrane fuel cell," Renewable Energy, Elsevier, vol. 211(C), pages 669-680.
    2. Li, Na & Cui, Xiaoti & Zhu, Jimin & Zhou, Mengfan & Liso, Vincenzo & Cinti, Giovanni & Sahlin, Simon Lennart & Araya, Samuel Simon, 2023. "A review of reformed methanol-high temperature proton exchange membrane fuel cell systems," Renewable and Sustainable Energy Reviews, Elsevier, vol. 182(C).
    3. Akira Nishimura & Tatsuya Okado & Yuya Kojima & Masafumi Hirota & Eric Hu, 2020. "Impact of MPL on Temperature Distribution in Single Polymer Electrolyte Fuel Cell with Various Thicknesses of Polymer Electrolyte Membrane," Energies, MDPI, vol. 13(10), pages 1-17, May.
    4. Giovanni Cinti & Vincenzo Liso & Simon Lennart Sahlin & Samuel Simon Araya, 2020. "System Design and Modeling of a High Temperature PEM Fuel Cell Operated with Ammonia as a Fuel," Energies, MDPI, vol. 13(18), pages 1-17, September.
    5. Hu, Zunyan & Xu, Liangfei & Huang, Yiyuan & Li, Jianqiu & Ouyang, Minggao & Du, Xiaoli & Jiang, Hongliang, 2018. "Comprehensive analysis of galvanostatic charge method for fuel cell degradation diagnosis," Applied Energy, Elsevier, vol. 212(C), pages 1321-1332.
    6. Nishimura, Akira & Yamamoto, Kohei & Okado, Tatsuya & Kojima, Yuya & Hirota, Masafumi & Kolhe, Mohan Lal, 2020. "Impact analysis of MPL and PEM thickness on temperature distribution within PEFC operating at relatively higher temperature," Energy, Elsevier, vol. 205(C).

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Li, Yan & Shi, Yan & Mehio, Nada & Tan, Mingsheng & Wang, Zhiyong & Hu, Xiaohong & Chen, George Z. & Dai, Sheng & Jin, Xianbo, 2016. "More sustainable electricity generation in hot and dry fuel cells with a novel hybrid membrane of Nafion/nano-silica/hydroxyl ionic liquid," Applied Energy, Elsevier, vol. 175(C), pages 451-458.
    2. Singdeo, Debanand & Dey, Tapobrata & Gaikwad, Shrihari & Andreasen, Søren Juhl & Ghosh, Prakash C., 2017. "A new modified-serpentine flow field for application in high temperature polymer electrolyte fuel cell," Applied Energy, Elsevier, vol. 195(C), pages 13-22.
    3. Zhang, S. & Reimer, U. & Beale, S.B. & Lehnert, W. & Stolten, D., 2019. "Modeling polymer electrolyte fuel cells: A high precision analysis," Applied Energy, Elsevier, vol. 233, pages 1094-1103.
    4. Purnima, P. & Jayanti, S., 2017. "Water neutrality and waste heat management in ethanol reformer - HTPEMFC integrated system for on-board hydrogen generation," Applied Energy, Elsevier, vol. 199(C), pages 169-179.
    5. Wu, Qixing & Li, Haiyang & Yuan, Wenxiang & Luo, Zhongkuan & Wang, Fang & Sun, Hongyuan & Zhao, Xuxin & Fu, Huide, 2015. "Performance evaluation of an air-breathing high-temperature proton exchange membrane fuel cell," Applied Energy, Elsevier, vol. 160(C), pages 146-152.
    6. Gabriele Loreti & Andrea Luigi Facci & Stefano Ubertini, 2021. "High-Efficiency Combined Heat and Power through a High-Temperature Polymer Electrolyte Membrane Fuel Cell and Gas Turbine Hybrid System," Sustainability, MDPI, vol. 13(22), pages 1-24, November.
    7. Víctor Sanz i López & Ramon Costa-Castelló & Carles Batlle, 2022. "Literature Review of Energy Management in Combined Heat and Power Systems Based on High-Temperature Proton Exchange Membrane Fuel Cells for Residential Comfort Applications," Energies, MDPI, vol. 15(17), pages 1-22, September.
    8. Pei, Pucheng & Chen, Huicui, 2014. "Main factors affecting the lifetime of Proton Exchange Membrane fuel cells in vehicle applications: A review," Applied Energy, Elsevier, vol. 125(C), pages 60-75.
    9. Ribeirinha, P. & Abdollahzadeh, M. & Sousa, J.M. & Boaventura, M. & Mendes, A., 2017. "Modelling of a high-temperature polymer electrolyte membrane fuel cell integrated with a methanol steam reformer cell," Applied Energy, Elsevier, vol. 202(C), pages 6-19.
    10. Di Marcoberardino, G. & Chiarabaglio, L. & Manzolini, G. & Campanari, S., 2019. "A Techno-economic comparison of micro-cogeneration systems based on polymer electrolyte membrane fuel cell for residential applications," Applied Energy, Elsevier, vol. 239(C), pages 692-705.
    11. Andújar, J.M. & Segura, F. & Isorna, F. & Calderón, A.J., 2018. "Comprehensive diagnosis methodology for faults detection and identification, and performance improvement of Air-Cooled Polymer Electrolyte Fuel Cells," Renewable and Sustainable Energy Reviews, Elsevier, vol. 88(C), pages 193-207.
    12. Thomas, Sobi & Bates, Alex & Park, Sam & Sahu, A.K. & Lee, Sang C. & Son, Byung Rak & Kim, Joo Gon & Lee, Dong-Ha, 2016. "An experimental and simulation study of novel channel designs for open-cathode high-temperature polymer electrolyte membrane fuel cells," Applied Energy, Elsevier, vol. 165(C), pages 765-776.
    13. Haghighat Mamaghani, Alireza & Najafi, Behzad & Casalegno, Andrea & Rinaldi, Fabio, 2017. "Predictive modelling and adaptive long-term performance optimization of an HT-PEM fuel cell based micro combined heat and power (CHP) plant," Applied Energy, Elsevier, vol. 192(C), pages 519-529.
    14. Ribeirinha, P. & Abdollahzadeh, M. & Boaventura, M. & Mendes, A., 2017. "H2 production with low carbon content via MSR in packed bed membrane reactors for high-temperature polymeric electrolyte membrane fuel cell," Applied Energy, Elsevier, vol. 188(C), pages 409-419.
    15. Najafi, Behzad & Haghighat Mamaghani, Alireza & Rinaldi, Fabio & Casalegno, Andrea, 2015. "Long-term performance analysis of an HT-PEM fuel cell based micro-CHP system: Operational strategies," Applied Energy, Elsevier, vol. 147(C), pages 582-592.
    16. Chen, Shiyi & Lior, Noam & Xiang, Wenguo, 2015. "Coal gasification integration with solid oxide fuel cell and chemical looping combustion for high-efficiency power generation with inherent CO2 capture," Applied Energy, Elsevier, vol. 146(C), pages 298-312.
    17. Peng, Fei & Zhao, Yuanzhe & Li, Xiaopeng & Liu, Zhixiang & Chen, Weirong & Liu, Yang & Zhou, Donghua, 2017. "Development of master-slave energy management strategy based on fuzzy logic hysteresis state machine and differential power processing compensation for a PEMFC-LIB-SC hybrid tramway," Applied Energy, Elsevier, vol. 206(C), pages 346-363.
    18. Pregelj, Boštjan & Micor, Michał & Dolanc, Gregor & Petrovčič, Janko & Jovan, Vladimir, 2016. "Impact of fuel cell and battery size to overall system performance – A diesel fuel-cell APU case study," Applied Energy, Elsevier, vol. 182(C), pages 365-375.
    19. Samsun, Remzi Can & Pasel, Joachim & Janßen, Holger & Lehnert, Werner & Peters, Ralf & Stolten, Detlef, 2014. "Design and test of a 5kWe high-temperature polymer electrolyte fuel cell system operated with diesel and kerosene," Applied Energy, Elsevier, vol. 114(C), pages 238-249.
    20. Chang, Huawei & Wan, Zhongmin & Zheng, Yao & Chen, Xi & Shu, Shuiming & Tu, Zhengkai & Chan, Siew Hwa & Chen, Rui & Wang, Xiaodong, 2017. "Energy- and exergy-based working fluid selection and performance analysis of a high-temperature PEMFC-based micro combined cooling heating and power system," Applied Energy, Elsevier, vol. 204(C), pages 446-458.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:appene:v:192:y:2017:i:c:p:422-436. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.elsevier.com/wps/find/journaldescription.cws_home/405891/description#description .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.