IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v17y2024i15p3827-d1448996.html
   My bibliography  Save this article

Turbulent Boundary Layer Control with Multi-Scale Riblet Design

Author

Listed:
  • Md. Rafsan Zani

    (Department of Mechanical Engineering, The University of Texas at Dallas, Richardson, TX 75080, USA)

  • Nir Saar Maor

    (Department of Mechanical Engineering, The University of Texas at Dallas, Richardson, TX 75080, USA)

  • Dhanush Bhamitipadi Suresh

    (Department of Mechanical Engineering, The University of Texas at Dallas, Richardson, TX 75080, USA)

  • Yaqing Jin

    (Department of Mechanical Engineering, The University of Texas at Dallas, Richardson, TX 75080, USA)

Abstract

Motivated by the saturation of drag reduction effectiveness at high non-dimensional riblet spacing in turbulent boundary layer flows, this study seeks to investigate the influence of a secondary blade riblet structure on flow statistics and friction drag reduction effectiveness in comparison to the widely explored single-scale blade riblet surface. The turbulent flow dynamics and drag reduction performance over single- and multi-scale blade riblet surfaces were experimentally examined in a flow visualization channel across various non-dimensional riblet spacings. The shear velocity was quantified by the streamwise velocity distributions from the logarithmic layer via planar Particle Image Velocimetry (PIV) measurements, whereas the near-wall flow dynamics were characterized by a Micro Particle Image Velocimetry (micro-PIV) system. The results highlighted that although both riblet surfaces exhibited similar drag reduction performances at low non-dimensional riblet spacings, the presence of a secondary riblet blade structure can effectively extend the drag reduction region with the non-dimensional riblet spacing up to 32 and achieve approximately 10% lower friction drag in comparison to the single-scale riblet surface when the non-dimensional riblet spacing increases to 44.2. The average number of uniform momentum zones (UMZs) on the multi-scaled blade riblet has also reduced by 9% compared to the single-scaled riblet which indicates the reduction of strong shear layers within a turbulent boundary layer. The inspection of near-wall flow statistics demonstrated that at high non-dimensional riblet spacings, the multi-scale riblet surface produces reduced wall-normal velocity fluctuations and Reynolds shear stresses. Quadrant analysis revealed that this design allows for the suppression of both the sweep and ejection events. This experimental result demonstrated that surfaces with spanwise variations of riblet heights have the potential to maintain drag reduction effectiveness across a wider range of flow speeds.

Suggested Citation

  • Md. Rafsan Zani & Nir Saar Maor & Dhanush Bhamitipadi Suresh & Yaqing Jin, 2024. "Turbulent Boundary Layer Control with Multi-Scale Riblet Design," Energies, MDPI, vol. 17(15), pages 1-15, August.
    • Handle: RePEc:gam:jeners:v:17:y:2024:i:15:p:3827-:d:1448996
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/17/15/3827/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/17/15/3827/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Moussavi, S. Abolfazl & Ghaznavi, Aidin, 2021. "Effect of boundary layer suction on performance of a 2 MW wind turbine," Energy, Elsevier, vol. 232(C).
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Wang, Peilin & Liu, Qingsong & Li, Chun & Miao, Weipao & Yue, Minnan & Xu, Zifei, 2022. "Investigation of the aerodynamic characteristics of horizontal axis wind turbine using an active flow control method via boundary layer suction," Renewable Energy, Elsevier, vol. 198(C), pages 1032-1048.
    2. Sun, Yukun & Qian, Yaoru & Wang, Tongguang & Wang, Long & Zhu, Chengyong & Gao, Yang, 2025. "Quantitative impact of combining blowing and suction flow control on a floating offshore wind turbine aerodynamic performance under the surge motion," Renewable Energy, Elsevier, vol. 238(C).
    3. Wang, Longjun & Alam, Md. Mahbub & Rehman, Shafiqur & Zhou, Yu, 2022. "Effects of blowing and suction jets on the aerodynamic performance of wind turbine airfoil," Renewable Energy, Elsevier, vol. 196(C), pages 52-64.
    4. Sun, Yukun & Qian, Yaoru & Wang, Tongguang & Wang, Long & Zhu, Chengyong & Gao, Yang, 2024. "Investigation of the wind turbine aerodynamic performance via the combining blowing and suction flow control," Energy, Elsevier, vol. 307(C).

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:17:y:2024:i:15:p:3827-:d:1448996. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.