IDEAS home Printed from https://ideas.repec.org/a/gam/jsusta/v12y2020i15p6167-d392487.html
   My bibliography  Save this article

Research Issues in the Process of Cutting Straw into Pieces

Author

Listed:
  • Marcin Zastempowski

    (Faculty of Mechanical Engineering, UTP University of Science and Technology, 85–796 Bydgoszcz, Poland)

  • Andrzej Bochat

    (Faculty of Mechanical Engineering, UTP University of Science and Technology, 85–796 Bydgoszcz, Poland)

Abstract

Comparative studies of the classical and new design of a chaff cutter’s cutting drum have been conducted within the frames of the study in order to determine their functional characteristics at the time of cutting rye straw into pieces of specific length (into chaff). A classical design of a cutting drum is of the shape of a roller and is suitable for material layer cross-cutting. However, the new drum design has the shape of a double truncated cone and, with the use of it, diagonal cuts in two directions can be realized. The studies were conducted for four designs of cutting drums with cutting angles α = 0° (classical design) and α = 15°, α = 30°, and α = 45° (new design). Three indicators were applied for the assessment: capacity, unit energy consumption, and the unit cutting resistance. The obtained results show that the use of a new drum design makes it possible, depending on the assumed parameters of the cutting process and the material’s compaction degree, to increase the process’s efficiency by up to 25%, lower the unit energy consumption up to 34%, and lower the unit cutting resistance by up to 8%. The conducted experimental studies have unequivocally shown that the use of a new cutting drum design, as compared to the classical one, results in a considerable increase in the cutting process’s performance. Studies on the new design of a chaff cutter’s cutting drum, of the shape of a double truncated cone, belong to original ones that so far have not been described in the available literature.

Suggested Citation

  • Marcin Zastempowski & Andrzej Bochat, 2020. "Research Issues in the Process of Cutting Straw into Pieces," Sustainability, MDPI, vol. 12(15), pages 1-12, July.
  • Handle: RePEc:gam:jsusta:v:12:y:2020:i:15:p:6167-:d:392487
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/2071-1050/12/15/6167/pdf
    Download Restriction: no

    File URL: https://www.mdpi.com/2071-1050/12/15/6167/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Weronika Kruszelnicka & Robert Kasner & Patrycja Bałdowska-Witos & Józef Flizikowski & Andrzej Tomporowski, 2020. "The Integrated Energy Consumption Index for Energy Biomass Grinding Technology Assessment," Energies, MDPI, vol. 13(6), pages 1-26, March.
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Viktoria Mannheim & Weronika Kruszelnicka, 2022. "Energy-Model and Life Cycle-Model for Grinding Processes of Limestone Products," Energies, MDPI, vol. 15(10), pages 1-20, May.
    2. Marcin Jewiarz & Marek Wróbel & Krzysztof Mudryk & Szymon Szufa, 2020. "Impact of the Drying Temperature and Grinding Technique on Biomass Grindability," Energies, MDPI, vol. 13(13), pages 1-22, July.
    3. Judit Lovasné Avató & Viktoria Mannheim, 2022. "Life Cycle Assessment Model of a Catering Product: Comparing Environmental Impacts for Different End-of-Life Scenarios," Energies, MDPI, vol. 15(15), pages 1-20, July.
    4. Viktoria Mannheim & Weronika Kruszelnicka, 2023. "Relation between Scale-Up and Life Cycle Assessment for Wet Grinding Process of Pumice," Energies, MDPI, vol. 16(11), pages 1-16, June.
    5. Weronika Kruszelnicka & Jakub Hlosta & Jan Diviš & Łukasz Gierz, 2021. "Study of the Relationships between Multi-Hole, Multi-Disc Mill Performance Parameters and Comminution Indicators," Sustainability, MDPI, vol. 13(15), pages 1-21, July.
    6. Marcin Zastempowski & Andrzej Bochat & Lubomír Hujo, 2021. "Selected Aspects of Modelling and Design Calculations of Roller Mills," Sustainability, MDPI, vol. 13(5), pages 1-10, March.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jsusta:v:12:y:2020:i:15:p:6167-:d:392487. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.