IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v15y2022i9p2971-d796754.html
   My bibliography  Save this article

Numerical Simulation of Gas Flow Passing through Slots of Various Shapes in Labyrinth Seals

Author

Listed:
  • Vadym Baha

    (Faculty of Technical Systems and Energy Efficient Technologies, Sumy State University, Rymskogo-Korsakova St. 2, 40007 Sumy, Ukraine)

  • Natalia Lishchenko

    (Faculty of Manufacturing Technologies, Technical University of Kosice, Bayerova 1, 08001 Prešov, Slovakia)

  • Serhiy Vanyeyev

    (Faculty of Technical Systems and Energy Efficient Technologies, Sumy State University, Rymskogo-Korsakova St. 2, 40007 Sumy, Ukraine)

  • Jana Mižáková

    (Faculty of Manufacturing Technologies, Technical University of Kosice, Bayerova 1, 08001 Prešov, Slovakia)

  • Tetiana Rodymchenko

    (Faculty of Technical Systems and Energy Efficient Technologies, Sumy State University, Rymskogo-Korsakova St. 2, 40007 Sumy, Ukraine)

  • Ján Piteľ

    (Faculty of Manufacturing Technologies, Technical University of Kosice, Bayerova 1, 08001 Prešov, Slovakia)

Abstract

Labyrinth seals are widely used in centrifugal compressors, turbines, and many other pneumatic systems due to their simplicity of design, reliability, and low cost. The calculation scheme for the movement of the working medium in a labyrinth seal is constructed by analogy with the movement of the working medium through holes with a sharp edge. Annular and flat slots, holes, and such a factor as the shaft rotation with a calculated sector of 3 degrees were studied. The purpose of the study is to determine the flow coefficient when the working medium flows through slots of various shapes. To achieve this purpose, modeling of the working medium flow in the FlowVision software was performed. The mass flow and flow coefficients are determined for the studied slot shapes. The convergence of the calculation results was determined by comparing the values of the mass flow rate at the inlet and outlet of the slot. Differences in visualizations of the flow for the studied variants of slots were established. The resulting difference should be taken into account in practical calculations of the working medium mass flow through the slot using a conditional flow rate factor which is determined by the slot design.

Suggested Citation

  • Vadym Baha & Natalia Lishchenko & Serhiy Vanyeyev & Jana Mižáková & Tetiana Rodymchenko & Ján Piteľ, 2022. "Numerical Simulation of Gas Flow Passing through Slots of Various Shapes in Labyrinth Seals," Energies, MDPI, vol. 15(9), pages 1-12, April.
    • Handle: RePEc:gam:jeners:v:15:y:2022:i:9:p:2971-:d:796754
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/15/9/2971/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/15/9/2971/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Serhii Khovanskyi & Ivan Pavlenko & Jan Pitel & Jana Mizakova & Marek Ochowiak & Irina Grechka, 2019. "Solving the Coupled Aerodynamic and Thermal Problem for Modeling the Air Distribution Devices with Perforated Plates," Energies, MDPI, vol. 12(18), pages 1-16, September.
    2. Zaniewski, Dawid & Klimaszewski, Piotr & Klonowicz, Piotr & Lampart, Piotr & Witanowski, Łukasz & Jędrzejewski, Łukasz & Suchocki, Tomasz & Antczak, Łukasz, 2021. "Performance of the honeycomb type sealings in organic vapour microturbines," Energy, Elsevier, vol. 226(C).
    Full references (including those not matched with items on IDEAS)

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Du, Qiuwan & Li, Yunzhu & Yang, Like & Liu, Tianyuan & Zhang, Di & Xie, Yonghui, 2022. "Performance prediction and design optimization of turbine blade profile with deep learning method," Energy, Elsevier, vol. 254(PA).
    2. Witanowski, Łukasz & Klonowicz, Piotr & Lampart, Piotr & Klimaszewski, Piotr & Suchocki, Tomasz & Jędrzejewski, Łukasz & Zaniewski, Dawid & Ziółkowski, Paweł, 2023. "Impact of rotor geometry optimization on the off-design ORC turbine performance," Energy, Elsevier, vol. 265(C).
    3. Hana Charvátová & Aleš Procházka & Martin Zálešák, 2020. "Computer Simulation of Passive Cooling of Wooden House Covered by Phase Change Material," Energies, MDPI, vol. 13(22), pages 1-15, November.
    4. Myung-Ho Kim & Van Toan Nguyen & Sunghyuk Im & Yohan Jung & Sun-Rock Choi & Byoung-Jae Kim, 2021. "Experimental Validation of Flow Uniformity Improvement by a Perforated Plate in the Heat Exchanger of SFR Steam Generator," Energies, MDPI, vol. 14(18), pages 1-17, September.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:15:y:2022:i:9:p:2971-:d:796754. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.