IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v13y2020i21p5837-d441922.html
   My bibliography  Save this article

Numerical Modelling and Experimental Verification of the Low-Emission Biomass Combustion Process in a Domestic Boiler with Flue Gas Flow around the Combustion Chamber

Author

Listed:
  • Przemysław Motyl

    (Faculty of Mechanical Engineering, University of Technology and Humanities in Radom, 26-600 Radom, Poland)

  • Danuta Król

    (Faculty of Energy and Environmental Engineering, Silesian University of Technology, 14-100 Gliwice, Poland)

  • Sławomir Poskrobko

    (Faculty of Civil Engineering and Environmental Sciences, Białystok University of Technology, 15-351 Białystok, Poland)

  • Marek Juszczak

    (Faculty of Environmental Engineering and Energy, Poznan University of Technology, 60-965 Poznań, Poland)

Abstract

The paper presents the results of numerical and experimental studies aimed at developing a new design of a 10 kW low-emission heating boiler fired with wood pellets. The boiler is to meet stringent requirements in terms of efficiency (η > 90%) and emissions per 10% O 2 : CO < 500 mg/Nm 3 , NOx ≤ 200 mg/Nm 3 , and dust ≤ 20 mg/Nm 3 ; these emission restrictions are as prescribed in the applicable ECODESIGN Directive in the European Union countries. An innovative aspect of the boiler structure (not yet present in domestic boilers) is the circular flow of exhaust gases around the centrally placed combustion chamber. The use of such a solution ensures high-efficiency, low-emission combustion and meeting the requirements of ECODESIGN. The results of the numerical calculations were verified and confirmed experimentally, obtaining average emission values of the limited gases CO = 91 mg/Nm 3 , and NOx = 197 mg/Nm 3 . The temperature measured in the furnace is 450–500 °C and in the flue it was 157–197 °C. The determined boiler efficiency was 92%. Numerical calculations were made with the use of an advanced CFD (Computational Fluid Dynamics) workshop in the form of the Ansys programming and a computing environment with the dominant participation of the Fluent module. It was shown that the results obtained in both experiments are sufficiently convergent.

Suggested Citation

  • Przemysław Motyl & Danuta Król & Sławomir Poskrobko & Marek Juszczak, 2020. "Numerical Modelling and Experimental Verification of the Low-Emission Biomass Combustion Process in a Domestic Boiler with Flue Gas Flow around the Combustion Chamber," Energies, MDPI, vol. 13(21), pages 1-16, November.
    • Handle: RePEc:gam:jeners:v:13:y:2020:i:21:p:5837-:d:441922
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/13/21/5837/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/13/21/5837/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Nakomcic-Smaragdakis, Branka & Cepic, Zoran & Dragutinovic, Natasa, 2016. "Analysis of solid biomass energy potential in Autonomous Province of Vojvodina," Renewable and Sustainable Energy Reviews, Elsevier, vol. 57(C), pages 186-191.
    2. Ferreira, Sérgio & Monteiro, Eliseu & Brito, Paulo & Vilarinho, Cândida, 2017. "Biomass resources in Portugal: Current status and prospects," Renewable and Sustainable Energy Reviews, Elsevier, vol. 78(C), pages 1221-1235.
    3. Büchner, Daniel & Schraube, Christian & Carlon, Elisa & von Sonntag, Justus & Schwarz, Markus & Verma, Vijay Kumar & Ortwein, Andreas, 2015. "Survey of modern pellet boilers in Austria and Germany – System design and customer satisfaction of residential installations," Applied Energy, Elsevier, vol. 160(C), pages 390-403.
    4. Chapela, S. & Porteiro, J. & Garabatos, M. & Patiño, D. & Gómez, M.A. & Míguez, J.L., 2019. "CFD study of fouling phenomena in small-scale biomass boilers: Experimental validation with two different boilers," Renewable Energy, Elsevier, vol. 140(C), pages 552-562.
    5. Malico, Isabel & Nepomuceno Pereira, Ricardo & Gonçalves, Ana Cristina & Sousa, Adélia M.O., 2019. "Current status and future perspectives for energy production from solid biomass in the European industry," Renewable and Sustainable Energy Reviews, Elsevier, vol. 112(C), pages 960-977.
    6. Verma, V.K. & Bram, S. & Delattin, F. & De Ruyck, J., 2013. "Real life performance of domestic pellet boiler technologies as a function of operational loads: A case study of Belgium," Applied Energy, Elsevier, vol. 101(C), pages 357-362.
    7. Letschert, Virginie & Desroches, Louis-Benoit & Ke, Jing & McNeil, Michael, 2013. "Energy efficiency – How far can we raise the bar? Revealing the potential of best available technologies," Energy, Elsevier, vol. 59(C), pages 72-82.
    8. Sungur, Bilal & Topaloglu, Bahattin, 2019. "An experimental investigation of the effect of smoke tube configuration on the performance and emission characteristics of pellet-fuelled boilers," Renewable Energy, Elsevier, vol. 143(C), pages 121-129.
    9. Dafnomilis, Ioannis & Hoefnagels, Ric & Pratama, Yudistira W. & Schott, Dingena L. & Lodewijks, Gabriel & Junginger, Martin, 2017. "Review of solid and liquid biofuel demand and supply in Northwest Europe towards 2030 – A comparison of national and regional projections," Renewable and Sustainable Energy Reviews, Elsevier, vol. 78(C), pages 31-45.
    10. Thomson, Harriet & Liddell, Christine, 2015. "The suitability of wood pellet heating for domestic households: A review of literature," Renewable and Sustainable Energy Reviews, Elsevier, vol. 42(C), pages 1362-1369.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Maulana G. Nugraha & Harwin Saptoadi & Muslikhin Hidayat & Bengt Andersson & Ronnie Andersson, 2021. "Particulate Matter Reduction in Residual Biomass Combustion," Energies, MDPI, vol. 14(11), pages 1-23, June.
    2. Dennis Krüger & Özge Çepelioğullar Mutlu, 2021. "Demonstration of a Top-Lit Updraft Based Pyrolytic Burner with Low Emission Operation and Automatic Process Control," Energies, MDPI, vol. 14(13), pages 1-16, June.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Vicente, E.D. & Vicente, A.M. & Evtyugina, M. & Tarelho, L.A.C. & Almeida, S.M. & Alves, C., 2020. "Emissions from residential combustion of certified and uncertified pellets," Renewable Energy, Elsevier, vol. 161(C), pages 1059-1071.
    2. Glasenapp, S. & Fonseca, M. & Weimar, H. & Döring, P. & Aguilar, F.X., 2021. "Conversion factors for residential wood energy in the European Union: an introduction to harmonizing units of measurement," Renewable and Sustainable Energy Reviews, Elsevier, vol. 138(C).
    3. Lelis Gonzaga Fraga & João Silva & Senhorinha Teixeira & Delfim Soares & Manuel Ferreira & José Teixeira, 2020. "Influence of Operating Conditions on the Thermal Behavior and Kinetics of Pine Wood Particles Using Thermogravimetric Analysis," Energies, MDPI, vol. 13(11), pages 1-22, June.
    4. Sungur, Bilal & Basar, Cem, 2023. "Experimental investigation of the effect of supply airflow position, excess air ratio and thermal power input at burner pot on the thermal and emission performances in a pellet stove," Renewable Energy, Elsevier, vol. 202(C), pages 1248-1258.
    5. Giuseppe Maggiotto & Gianpiero Colangelo & Marco Milanese & Arturo de Risi, 2023. "Thermochemical Technologies for the Optimization of Olive Wood Biomass Energy Exploitation: A Review," Energies, MDPI, vol. 16(19), pages 1-17, September.
    6. Kütt, Lauri & Millar, John & Karttunen, Antti & Lehtonen, Matti & Karppinen, Maarit, 2018. "Thermoelectric applications for energy harvesting in domestic applications and micro-production units. Part I: Thermoelectric concepts, domestic boilers and biomass stoves," Renewable and Sustainable Energy Reviews, Elsevier, vol. 98(C), pages 519-544.
    7. Menegon, Diego & Soppelsa, Anton & Fedrizzi, Roberto, 2017. "Development of a new dynamic test procedure for the laboratory characterization of a whole heating and cooling system," Applied Energy, Elsevier, vol. 205(C), pages 976-990.
    8. Oliveira, Mario Henrique da Fonseca & Rebelatto, Daisy Aparecida do Nascimento, 2015. "The evaluation of electric energy consumption in the Brazilian residential sector: A technological improvement proposal in order to increase its efficiency," Renewable and Sustainable Energy Reviews, Elsevier, vol. 49(C), pages 836-844.
    9. Sérgio Ferreira & Eliseu Monteiro & Luís Calado & Valter Silva & Paulo Brito & Cândida Vilarinho, 2019. "Experimental and Modeling Analysis of Brewers´ Spent Grains Gasification in a Downdraft Reactor," Energies, MDPI, vol. 12(23), pages 1-18, November.
    10. Sekoai, Patrick T. & Chunilall, Viren & Msele, Kwanele & Buthelezi, Lindiswa & Johakimu, Jonas & Andrew, Jerome & Zungu, Manqoba & Moloantoa, Karabelo & Maningi, Nontuthuko & Habimana, Olivier & Swart, 2023. "Biowaste biorefineries in South Africa: Current status, opportunities, and research and development needs," Renewable and Sustainable Energy Reviews, Elsevier, vol. 188(C).
    11. Ferraz de Campos, Victor Arruda & Silva, Valter Bruno & Cardoso, João Sousa & Brito, Paulo S. & Tuna, Celso Eduardo & Silveira, José Luz, 2021. "A review of waste management in Brazil and Portugal: Waste-to-energy as pathway for sustainable development," Renewable Energy, Elsevier, vol. 178(C), pages 802-820.
    12. Elena Tamburini & Mattias Gaglio & Giuseppe Castaldelli & Elisa Anna Fano, 2020. "Is Bioenergy Truly Sustainable When Land-Use-Change (LUC) Emissions Are Accounted for? The Case-Study of Biogas from Agricultural Biomass in Emilia-Romagna Region, Italy," Sustainability, MDPI, vol. 12(8), pages 1-20, April.
    13. Fábio de Oliveira Neves & Henrique Ewbank & José Arnaldo Frutuoso Roveda & Andrea Trianni & Fernando Pinhabel Marafão & Sandra Regina Monteiro Masalskiene Roveda, 2022. "Economic and Production-Related Implications for Industrial Energy Efficiency: A Logistic Regression Analysis on Cross-Cutting Technologies," Energies, MDPI, vol. 15(4), pages 1-19, February.
    14. Chapela, Sergio & Cid, Natalia & Porteiro, Jacobo & Míguez, José Luis, 2020. "Numerical transient modelling of the fouling phenomena and its influence on thermal performance in a low-scale biomass shell boiler," Renewable Energy, Elsevier, vol. 161(C), pages 309-318.
    15. Munawar, Muhammad Assad & Khoja, Asif Hussain & Naqvi, Salman Raza & Mehran, Muhammad Taqi & Hassan, Muhammad & Liaquat, Rabia & Dawood, Usama Fida, 2021. "Challenges and opportunities in biomass ash management and its utilization in novel applications," Renewable and Sustainable Energy Reviews, Elsevier, vol. 150(C).
    16. Zou, Chenchen & Ma, Minda & Zhou, Nan & Feng, Wei & You, Kairui & Zhang, Shufan, 2023. "Toward carbon free by 2060: A decarbonization roadmap of operational residential buildings in China," Energy, Elsevier, vol. 277(C).
    17. Brand, Martha Andreia & Jacinto, Rodolfo Cardoso, 2020. "Apple pruning residues: Potential for burning in boiler systems and pellet production," Renewable Energy, Elsevier, vol. 152(C), pages 458-466.
    18. Sergio Paniagua & Alba Prado-Guerra & Ana Isabel Neto & Teresa Nunes & Luís Tarelho & Célia Alves & Luis Fernando Calvo, 2020. "Influence of Varieties and Organic Fertilizer in the Elaboration of a New Poplar-Straw Pellet and Its Emissions in a Domestic Boiler," Energies, MDPI, vol. 13(23), pages 1-17, November.
    19. Zhu, Tong & Curtis, John & Clancy, Matthew, 2023. "Modelling barriers to low-carbon technologies in energy system analysis: The example of renewable heat in Ireland," Applied Energy, Elsevier, vol. 330(PA).
    20. Mina Masoomi & Mostafa Panahi & Reza Samadi, 2022. "Demand side management for electricity in Iran: cost and emission analysis using LEAP modeling framework," Environment, Development and Sustainability: A Multidisciplinary Approach to the Theory and Practice of Sustainable Development, Springer, vol. 24(4), pages 5667-5693, April.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:13:y:2020:i:21:p:5837-:d:441922. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.