IDEAS home Printed from https://ideas.repec.org/a/eee/energy/v60y2013icp333-343.html
   My bibliography  Save this article

Thermal analysis of novel minichannel-based solar flat-plate collector

Author

Listed:
  • Khamis Mansour, M.

Abstract

This paper investigates thermal performance of a new design of minichannel-based solar flat-plate collector. The solar collector consists of an array of minichannels located in the absorber plate which is covered by single glass cover. Water was used as the working fluid. A numerical model was implemented to determine the heat transfer characteristics and pressure drop of the working fluid inside the minichannels. The numerical model was verified by comparing the predicated results with those obtained from the available analytical and experimental data with maximum deviation of 10%. A program code was developed using Engineering Equation Solver EES software in order to predict the thermal performance of the novel solar collector at any operating conditions. The code is based on energy balance and heat transfer equations assuming a quasi-steady state condition. A small-scale of this novel solar collector, with an absorber plate area of 0.6 m2, is experimentally tested during month of June in Beirut. The experimental test was conducted aiming to validate the computer program in terms of the calculation of the instantaneous efficiency and overall heat loss coefficient. There was a good agreement between the analytical and experimental results with a maximum deviation of less than 10% for instantaneous efficiency and 20.4% for predication of overall heat loss coefficient. The thermal and hydraulic performance of the proposed novel collector was compared to that of the conventional flat-plate solar collector. The comparison revealed that the heat removal factor of the novel collector is higher than that of the conventional one by 16.1%. Effect of varying mass flow rate of the working fluid on the new collector's thermal and hydraulic performance has been also studied.

Suggested Citation

  • Khamis Mansour, M., 2013. "Thermal analysis of novel minichannel-based solar flat-plate collector," Energy, Elsevier, vol. 60(C), pages 333-343.
  • Handle: RePEc:eee:energy:v:60:y:2013:i:c:p:333-343
    DOI: 10.1016/j.energy.2013.08.013
    as

    Download full text from publisher

    File URL: http://www.sciencedirect.com/science/article/pii/S0360544213006889
    Download Restriction: Full text for ScienceDirect subscribers only

    File URL: https://libkey.io/10.1016/j.energy.2013.08.013?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    As the access to this document is restricted, you may want to search for a different version of it.

    References listed on IDEAS

    as
    1. Mittal, M.K. & Varun, & Saini, R.P. & Singal, S.K., 2007. "Effective efficiency of solar air heaters having different types of roughness elements on the absorber plate," Energy, Elsevier, vol. 32(5), pages 739-745.
    2. Naphon, Paisarn & Wongwises, Somchai, 2006. "A review of flow and heat transfer characteristics in curved tubes," Renewable and Sustainable Energy Reviews, Elsevier, vol. 10(5), pages 463-490, October.
    3. Jaisankar, S. & Radhakrishnan, T.K. & Sheeba, K.N., 2009. "Studies on heat transfer and friction factor characteristics of thermosyphon solar water heating system with helical twisted tapes," Energy, Elsevier, vol. 34(9), pages 1054-1064.
    4. Jaisankar, S. & Ananth, J. & Thulasi, S. & Jayasuthakar, S.T. & Sheeba, K.N., 2011. "A comprehensive review on solar water heaters," Renewable and Sustainable Energy Reviews, Elsevier, vol. 15(6), pages 3045-3050, August.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Zhou, Ruiwen & Ling, Xiang & Peng, Hao & Yang, Lin, 2018. "Thermal characteristics of the combined flat plate heat receiver in solar power tower plant," Energy, Elsevier, vol. 165(PA), pages 275-289.
    2. Filipović, P. & Dović, D. & Horvat, I. & Ranilović, B., 2023. "Evaluation of a novel polymer solar collector using numerical and experimental methods," Energy, Elsevier, vol. 284(C).
    3. Zhou, Liqun & Wang, Yiping & Huang, Qunwu, 2019. "Parametric analysis on the performance of flat plate collector with transparent insulation material," Energy, Elsevier, vol. 174(C), pages 534-542.
    4. Evangelisti, Luca & De Lieto Vollaro, Roberto & Asdrubali, Francesco, 2019. "Latest advances on solar thermal collectors: A comprehensive review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 114(C), pages 1-1.
    5. Ischia Kurniawati & Yonmo Sung, 2024. "A Review of Heat Dissipation and Absorption Technologies for Enhancing Performance in Photovoltaic–Thermal Systems," Energies, MDPI, vol. 17(7), pages 1-29, April.
    6. Verma, Sujit Kumar & Sharma, Kamal & Gupta, Naveen Kumar & Soni, Pawan & Upadhyay, Neeraj, 2020. "“Performance comparison of innovative spiral shaped solar collector design with conventional flat plate solar collector”," Energy, Elsevier, vol. 194(C).
    7. Li, Qiyuan & Shirazi, Ali & Zheng, Cheng & Rosengarten, Gary & Scott, Jason A. & Taylor, Robert A., 2016. "Energy concentration limits in solar thermal heating applications," Energy, Elsevier, vol. 96(C), pages 253-267.
    8. Sharma, Harish Kumar & Kumar, Satish & Verma, Sujit Kumar, 2022. "Comparative performance analysis of flat plate solar collector having circular &trapezoidal corrugated absorber plate designs," Energy, Elsevier, vol. 253(C).
    9. Pandey, Krishna Murari & Chaurasiya, Rajesh, 2017. "A review on analysis and development of solar flat plate collector," Renewable and Sustainable Energy Reviews, Elsevier, vol. 67(C), pages 641-650.
    10. Vahidinia, F. & Khorasanizadeh, H., 2021. "Development of new algebraic derivations to analyze minichannel solar flat plate collectors with small and large size minichannels and performance evaluation study," Energy, Elsevier, vol. 228(C).
    11. Ana Cristina Ferreira & Angela Silva & José Carlos Teixeira & Senhorinha Teixeira, 2020. "Multi-Objective Optimization of Solar Thermal Systems Applied to Portuguese Dwellings," Energies, MDPI, vol. 13(24), pages 1-23, December.
    12. Tabish Alam & Nagesh Babu Balam & Kishor Sitaram Kulkarni & Md Irfanul Haque Siddiqui & Nishant Raj Kapoor & Chandan Swaroop Meena & Ashok Kumar & Raffaello Cozzolino, 2021. "Performance Augmentation of the Flat Plate Solar Thermal Collector: A Review," Energies, MDPI, vol. 14(19), pages 1-23, September.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. Jaisankar, S. & Ananth, J. & Thulasi, S. & Jayasuthakar, S.T. & Sheeba, K.N., 2011. "A comprehensive review on solar water heaters," Renewable and Sustainable Energy Reviews, Elsevier, vol. 15(6), pages 3045-3050, August.
    2. Balaji, K. & Ganesh Kumar, P. & Sakthivadivel, D. & Vigneswaran, V.S. & Iniyan, S., 2019. "Experimental investigation on flat plate solar collector using frictionally engaged thermal performance enhancer in the absorber tube," Renewable Energy, Elsevier, vol. 142(C), pages 62-72.
    3. Suman, Siddharth & Khan, Mohd. Kaleem & Pathak, Manabendra, 2015. "Performance enhancement of solar collectors—A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 49(C), pages 192-210.
    4. Maadi, Seyed Reza & Navegi, Ali & Solomin, Evgeny & Ahn, Ho Seon & Wongwises, Somchai & Mahian, Omid, 2021. "Performance improvement of a photovoltaic-thermal system using a wavy-strip insert with and without nanofluid," Energy, Elsevier, vol. 234(C).
    5. Khargotra, Rohit & Kumar, Raj & András, Kovács & Fekete, Gusztáv & Singh, Tej, 2022. "Thermo-hydraulic characterization and design optimization of delta-shaped obstacles in solar water heating system using CRITIC-COPRAS approach," Energy, Elsevier, vol. 261(PB).
    6. Sundar, L. Syam & Singh, Manoj K. & Punnaiah, V. & Sousa, Antonio C.M., 2018. "Experimental investigation of Al2O3/water nanofluids on the effectiveness of solar flat-plate collectors with and without twisted tape inserts," Renewable Energy, Elsevier, vol. 119(C), pages 820-833.
    7. Chamoli, Sunil, 2015. "Hybrid FAHP (fuzzy analytical hierarchy process)-FTOPSIS (fuzzy technique for order preference by similarity of an ideal solution) approach for performance evaluation of the V down perforated baffle r," Energy, Elsevier, vol. 84(C), pages 432-442.
    8. Amani, E. & Nobari, M.R.H., 2011. "A numerical investigation of entropy generation in the entrance region of curved pipes at constant wall temperature," Energy, Elsevier, vol. 36(8), pages 4909-4918.
    9. Michael-Allan Millar & Bruce Elrick & Greg Jones & Zhibin Yu & Neil M. Burnside, 2020. "Roadblocks to Low Temperature District Heating," Energies, MDPI, vol. 13(22), pages 1-21, November.
    10. Alva, Guruprasad & Lin, Yaxue & Fang, Guiyin, 2018. "An overview of thermal energy storage systems," Energy, Elsevier, vol. 144(C), pages 341-378.
    11. Evangelisti, Luca & De Lieto Vollaro, Roberto & Asdrubali, Francesco, 2019. "Latest advances on solar thermal collectors: A comprehensive review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 114(C), pages 1-1.
    12. Bessa, Vanessa M.T. & Prado, Racine T.A., 2015. "Reduction of carbon dioxide emissions by solar water heating systems and passive technologies in social housing," Energy Policy, Elsevier, vol. 83(C), pages 138-150.
    13. Shukla, Ruchi & Sumathy, K. & Erickson, Phillip & Gong, Jiawei, 2013. "Recent advances in the solar water heating systems: A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 19(C), pages 173-190.
    14. Nidhul, Kottayat & Kumar, Sachin & Yadav, Ajay Kumar & Anish, S., 2020. "Enhanced thermo-hydraulic performance in a V-ribbed triangular duct solar air heater: CFD and exergy analysis," Energy, Elsevier, vol. 200(C).
    15. Agung Tri Wijayanta & Pranowo & Mirmanto & Budi Kristiawan & Muhammad Aziz, 2019. "Internal Flow in an Enhanced Tube Having Square-cut Twisted Tape Insert," Energies, MDPI, vol. 12(2), pages 1-12, January.
    16. Zhou, Chaohui & Ni, Long & Yao, Yang, 2018. "Heat transfer analysis of multi-row helically coiled tube heat exchangers for surface water-source heat pump," Energy, Elsevier, vol. 163(C), pages 1032-1049.
    17. Guanming Guo & Masaya Kamigaki & Yuuya Inoue & Keiya Nishida & Hitoshi Hongou & Masanobu Koutoku & Ryo Yamamoto & Hideaki Yokohata & Shinji Sumi & Yoichi Ogata, 2021. "Experimental Study and Conjugate Heat Transfer Simulation of Pulsating Flow in Straight and 90° Curved Square Pipes," Energies, MDPI, vol. 14(13), pages 1-20, July.
    18. Gautam, Abhishek & Chamoli, Sunil & Kumar, Alok & Singh, Satyendra, 2017. "A review on technical improvements, economic feasibility and world scenario of solar water heating system," Renewable and Sustainable Energy Reviews, Elsevier, vol. 68(P1), pages 541-562.
    19. El-Sebaii, A.A. & Al-Snani, H., 2010. "Effect of selective coating on thermal performance of flat plate solar air heaters," Energy, Elsevier, vol. 35(4), pages 1820-1828.
    20. Sheikholeslami, Mohsen & Gorji-Bandpy, Mofid & Ganji, Davood Domiri, 2015. "Review of heat transfer enhancement methods: Focus on passive methods using swirl flow devices," Renewable and Sustainable Energy Reviews, Elsevier, vol. 49(C), pages 444-469.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:eee:energy:v:60:y:2013:i:c:p:333-343. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: Catherine Liu (email available below). General contact details of provider: http://www.journals.elsevier.com/energy .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.