IDEAS home Printed from https://ideas.repec.org/a/plo/pone00/0315851.html
   My bibliography  Save this article

Estimating whole-body centre of mass sway during quiet standing with inertial measurement units

Author

Listed:
  • Liam H Foulger
  • Emma R Reiter
  • Calvin Kuo
  • Mark G Carpenter
  • Jean-Sébastien Blouin

Abstract

Our ability to balance upright provides a stable platform to perform daily activities. Balance deficits associated with various clinical conditions may affect activities of daily living, highlighting the importance of quantifying standing balance in ecological environments. Although typically performed in laboratory settings, the growing availability of low-cost inertial measurement units (IMUs) allows the assessment of balance in the real world. However, it is unclear how many IMUs are required to adequately estimate linear displacements of the centre of mass (CoM) at stance widths associated with daily activities. While wearing IMUs on their head, sternum, back, right thigh, right shank, and left shank, 16 participants stood quietly on a force platform in narrow, hip-width, and shoulder-width stances, each for three two-minute trials. Using a multi-segment biomechanical model, we estimated CoM displacements from all possible combinations of the IMUs. We then calculated the correlation between the IMU- and force platform- CoM estimates to determine the minimal number of IMUs needed to estimate CoM sway. Four IMUs were necessary to accurately estimate anteroposterior (AP) and mediolateral (ML) CoM displacements across stance widths. Using IMUs on the back, right thigh, and both shanks, we found strong correlations between the IMU CoM estimation and the force platform CoM estimation in narrow stance (AP: r = 0.92±0.04, RMSE = 2.39±2.08 mm; ML: r = 0.97±0.02, RMSE = 1.16±0.77 mm), hip-width stance (AP: r = 0.93±0.04, RMSE = 2.00±1.18 mm; ML: r = 0.92±0.06, RMSE = 0.92±0.70 mm), and shoulder-width stance (AP: r = 0.93±0.03, RMSE = 1.95±1.66 mm; ML: r = 0.86±0.13, RMSE = 1.39±1.46 mm). These results indicate that IMUs can be used to estimate CoM displacements during quiet standing and that four IMUs are necessary to do so. Using an algorithm based on a simple biomechanical model, researchers and clinicians can estimate whole-body CoM displacements accurately during unperturbed quiet standing. This approach can improve the ecological validity of standing balance research and opens the possibility for assessing/monitoring patients with standing balance deficits.

Suggested Citation

  • Liam H Foulger & Emma R Reiter & Calvin Kuo & Mark G Carpenter & Jean-Sébastien Blouin, 2025. "Estimating whole-body centre of mass sway during quiet standing with inertial measurement units," PLOS ONE, Public Library of Science, vol. 20(1), pages 1-13, January.
  • Handle: RePEc:plo:pone00:0315851
    DOI: 10.1371/journal.pone.0315851
    as

    Download full text from publisher

    File URL: https://journals.plos.org/plosone/article?id=10.1371/journal.pone.0315851
    Download Restriction: no

    File URL: https://journals.plos.org/plosone/article/file?id=10.1371/journal.pone.0315851&type=printable
    Download Restriction: no

    File URL: https://libkey.io/10.1371/journal.pone.0315851?utm_source=ideas
    LibKey link: if access is restricted and if your library uses this service, LibKey will redirect you to where you can use your library subscription to access this item
    ---><---

    More about this item

    Statistics

    Access and download statistics

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:plo:pone00:0315851. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    We have no bibliographic references for this item. You can help adding them by using this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: plosone (email available below). General contact details of provider: https://journals.plos.org/plosone/ .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.