Author
Listed:
- Xiaojun Ning
(School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083, China)
- Zheng Ren
(School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083, China)
- Guangze Kan
(School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083, China)
- Haibin Zhang
(Beijing Shougang Corporation Ironmaking Division, Tangshan 064400, China)
- Junyi Wu
(School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083, China)
- Guangwei Wang
(School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083, China)
Abstract
In order to alleviate the energy crisis and respond to the “dual carbon strategy”, a new energy substance is needed to replace pulverized coal as the new blast furnace blowing fuel. Hydrochar is a clean and renewable carbon resource with high calorific value, good transportation and storage properties, and low ash content. Numerical simulation is used to study the combustion process of co-blown pulverized coal and hydrochar inside the cyclone zone. In this study, a three-dimensional physical model was constructed based on the actual dimensions of the direct-blowing pipe, tuyere, coal gun, and swirl zone of a large blast furnace in China. Numerical simulation methods were used to study the combustion process of coal powder and hydrothermal carbon co-injected into the swirl zone, and to investigate changes in the swirl zone of the tuyere under different conditions. The results show that increasing the proportion of hydrochar in the blended coal is conducive to improving the combustion rate of the blended coal, the temperature inside the gyratory zone increases significantly with the increase in the oxygen enrichment rate, and the high temperature zone is gradually enlarged. For every 1% increase in the oxygen enrichment rate, the maximum temperature of the centerline of the coal plume increases by 28 K, and the burnout rate increases by 1.12%; the increase in the blast temperature makes the combustion of pulverized coal slightly advance and promotes the increase in the internal temperature of the gyratory zone. The change of the blast temperature to 1559 K is more obvious, and the increase in the blast temperature after it is greater than 1559 K is not significant for the improvement of the burnout rate and the temperature of the gyratory area, and it will increase the cost; the lower the proportion of the small particle size is, the bigger the high temperature area of the gyratory area is, and the higher the temperature of the centerline of the coal strand is. If the content of the volatile matter remains unchanged, the increase in the ratio of the hydrochar has little influence on the temperature field of the gyratory area and the temperature of the centerline of the coal strand. The temperature difference is kept at 20 K. With the increase in the hydrochar ratio, the overall burnout rate of pulverized coal gradually increases. Therefore, hydrochar can replace bituminous coal as blast furnace blowing fuel to a certain extent, which can reduce costs and carbon emissions.
Suggested Citation
Xiaojun Ning & Zheng Ren & Guangze Kan & Haibin Zhang & Junyi Wu & Guangwei Wang, 2025.
"Numerical Simulation Study of Blast Furnace Mixed Blown Pulverized Coal and Hydrochar,"
Sustainability, MDPI, vol. 17(18), pages 1-18, September.
Handle:
RePEc:gam:jsusta:v:17:y:2025:i:18:p:8122-:d:1745824
Download full text from publisher
Corrections
All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jsusta:v:17:y:2025:i:18:p:8122-:d:1745824. See general information about how to correct material in RePEc.
If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.
We have no bibliographic references for this item. You can help adding them by using this form .
If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.
For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .
Please note that corrections may take a couple of weeks to filter through
the various RePEc services.