IDEAS home Printed from https://ideas.repec.org/a/gam/jsusta/v15y2023i24p16602-d1295060.html
   My bibliography  Save this article

Recycling Waste Plastics into Plastic-Bonded Sand Interlocking Blocks for Wall Construction in Developing Countries

Author

Listed:
  • Alexander Kumi-Larbi Jnr

    (UKCRIC Advanced Infrastructure Materials Laboratory, Department of Civil and Environmental Engineering, Imperial College London, London SW7 2BU, UK)

  • Latifatu Mohammed

    (Council for Scientific and Industrial Research, Institute of Industrial Research, Accra P.O. Box LG 587, Ghana)

  • Trinity Ama Tagbor

    (Council for Scientific and Industrial Research, Institute of Industrial Research, Accra P.O. Box LG 587, Ghana)

  • Samuel Kofi Tulashie

    (Industrial Chemistry Section, Department of Chemistry, School of Physical Sciences, College of Agriculture and Natural Sciences, University of Cape Coast, Cape Coast PMB TF0494, Ghana)

  • Christopher Cheeseman

    (UKCRIC Advanced Infrastructure Materials Laboratory, Department of Civil and Environmental Engineering, Imperial College London, London SW7 2BU, UK)

Abstract

This paper reports on using waste polyethylene to form plastic-bonded sand interlocking blocks for wall construction. The production process, mechanical properties, and failure mechanisms of three different interlocking block wall systems are reported. Plastic-bonded composite blocks were formed by mixing sand into waste polyethylene in a high-temperature extruder. The blocks formed had densities between 1.5 and 1.6 g cm −3 and compressive strengths of approximately 15.0 MPa. This is significantly higher than the conventional sandcrete wall blocks that are widely used in developing countries. The blocks were used to construct walls with dimensions of 1.0 m × 1.0 m × 0.15 m, and these were subjected to in-plane compressive loads. The compressive strengths of the walls ranged from 4.2 to 5.7 MPa. Variations in the block composition did not affect the failure mechanism, but the extent of the block damage after failure varied significantly. The potential for using waste plastics to form interlocking construction blocks for use in low-cost construction is discussed.

Suggested Citation

  • Alexander Kumi-Larbi Jnr & Latifatu Mohammed & Trinity Ama Tagbor & Samuel Kofi Tulashie & Christopher Cheeseman, 2023. "Recycling Waste Plastics into Plastic-Bonded Sand Interlocking Blocks for Wall Construction in Developing Countries," Sustainability, MDPI, vol. 15(24), pages 1-21, December.
    • Handle: RePEc:gam:jsusta:v:15:y:2023:i:24:p:16602-:d:1295060
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/2071-1050/15/24/16602/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/2071-1050/15/24/16602/
    Download Restriction: no
    ---><---

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jsusta:v:15:y:2023:i:24:p:16602-:d:1295060. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    We have no bibliographic references for this item. You can help adding them by using this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.