IDEAS home Printed from https://ideas.repec.org/a/gam/jsusta/v14y2022i14p8589-d862133.html
   My bibliography  Save this article

Impacts of Fracture Roughness and Near-Wellbore Tortuosity on Proppant Transport within Hydraulic Fractures

Author

Listed:
  • Di Wang

    (State Key Laboratory of Shale Oil and Gas Enrichment Mechanisms and Effective Development, Beijing 100083, China
    National Energy Shale Oil Research and Development Center, Beijing 100083, China)

  • Bingyang Bai

    (Unconventional Petroleum Research Institute, China University of Petroleum at Beijing, Beijing 102249, China)

  • Bin Wang

    (Unconventional Petroleum Research Institute, China University of Petroleum at Beijing, Beijing 102249, China)

  • Dongya Wei

    (Unconventional Petroleum Research Institute, China University of Petroleum at Beijing, Beijing 102249, China)

  • Tianbo Liang

    (Unconventional Petroleum Research Institute, China University of Petroleum at Beijing, Beijing 102249, China)

Abstract

For unconventional reservoir hydraulic fracturing design, a greater fracture length is a prime factor to optimize. However, the core observation results from the Hydraulic Fracturing Test Site (HFTS) show that the propped fractures are far less or shorter than expected, which suggests that the roughness and tortuosity of hydraulic fractures are crucial to sand transport. In this study, a transport model of sands is first built based on experimental measurements on the height and transport velocity of the sand bank in fractures with predetermined width and roughness. The fracture roughness is quantified by using the surface height integral. Then, three-dimensional simulations are conducted with this modified model to further investigate the impact of tortuous fractures on sand transport, from which a regression model is established to estimate the propped length of hydraulic fractures at a certain pumping condition. The experiment results show that the height of the sand bank in rough fractures is 20–50% higher than that in smooth fractures. The height of the sand bank decreases with the reduction in slurry velocity and increases with the increase in sand diameter. Sand sizes do little effect on the transport velocity of the sand bank, but the increase in slurry velocity and sand volume fraction can dramatically enhance the migration velocity of the sand bank. The appearance of tortuous fractures decreases the horizontal velocity of suspended particles and results in a higher sand bank compared with that in straight fractures. When the sand bank reaches equilibrium at the tortuous position, it is easy to produce vortices. So, there is a significant height of sand bank change at the tortuous position. Moreover, sand plugging can occur at the entrance of the fractures, making it difficult for the sand to transport deep into fractures. This study explains why the propped length of fractures in HFTS is short and provides a regression model that can be easily embedded in the fracturing simulation to quickly calculate dimensions of the propped fractures network to predict the length and height of propped fractures during fracturing.

Suggested Citation

  • Di Wang & Bingyang Bai & Bin Wang & Dongya Wei & Tianbo Liang, 2022. "Impacts of Fracture Roughness and Near-Wellbore Tortuosity on Proppant Transport within Hydraulic Fractures," Sustainability, MDPI, vol. 14(14), pages 1-22, July.
  • Handle: RePEc:gam:jsusta:v:14:y:2022:i:14:p:8589-:d:862133
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/2071-1050/14/14/8589/pdf
    Download Restriction: no

    File URL: https://www.mdpi.com/2071-1050/14/14/8589/
    Download Restriction: no
    ---><---

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jsusta:v:14:y:2022:i:14:p:8589-:d:862133. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    We have no bibliographic references for this item. You can help adding them by using this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.