IDEAS home Printed from https://ideas.repec.org/a/gam/jsusta/v12y2020i15p6095-d391427.html
   My bibliography  Save this article

Reduction of Inrush Current in a Shockwave Non-Thermal Food Processing System Using an Exponential Clock Pulse Generator

Author

Listed:
  • Kei Eguchi

    (Department of Information Electronics, Fukuoka Institute of Technology, Fukuoka 811-0295, Japan)

  • Farzin Asadi

    (Department of Electrical and Electronics Engineering, Maltepe University, 34857 Istanbul, Turkey)

  • Akira Shibata

    (Department of Information Electronics, Fukuoka Institute of Technology, Fukuoka 811-0295, Japan)

  • Hiroto Abe

    (Department of Information Electronics, Fukuoka Institute of Technology, Fukuoka 811-0295, Japan)

  • Ichirou Oota

    (Department of Information, Communication and Electronic Engineering, National Institute of Technology, Kumamoto College, Kumamoto 861-1102, Japan)

Abstract

Recently, shockwave food processing is drawing much attention as a low-cost non-thermal food process technique. In shockwave non-thermal food processing, underwater shockwaves are generated by a high voltage generator. Therefore, high inrush currents and high voltage stress on circuit components significantly reduce the reliability and life expectancy of the circuit. However, to the best of our knowledge, stress reduction techniques and their experimental verification have not been studied yet in the shockwave non-thermal food processing system. In this paper, we propose a stress reduction technique for the shockwave non-thermal food processing system and investigate the effectiveness of the proposed technique experimentally. To achieve high reliability and life expectancy, a new high voltage multiplier with an exponential clock pulse generator is proposed for the shockwave non-thermal food processing system. By slowing down the rate at which the capacitors charge in the high voltage multiplier, the exponential clock pulse generator significantly reduces the inrush current. Furthermore, to perform shockwave non-thermal food processing continuously at a lower voltage level, we present a new electrode with a reset mechanism for wire electric discharge (WED), where a square-shaped metal wire swings on a hinge in the proposed electrode. The proposed electrode enables not only shockwave generation at a lower voltage level but also continuous non-thermal food processing, because the square-shaped metal wire is not melted in the WED process. To confirm the validity of the proposed techniques, some experiments are performed regarding the laboratory prototype of the shockwave non-thermal food processing system. In the performed experiments, reduction of inrush currents and effective food processing are confirmed.

Suggested Citation

  • Kei Eguchi & Farzin Asadi & Akira Shibata & Hiroto Abe & Ichirou Oota, 2020. "Reduction of Inrush Current in a Shockwave Non-Thermal Food Processing System Using an Exponential Clock Pulse Generator," Sustainability, MDPI, vol. 12(15), pages 1-20, July.
  • Handle: RePEc:gam:jsusta:v:12:y:2020:i:15:p:6095-:d:391427
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/2071-1050/12/15/6095/pdf
    Download Restriction: no

    File URL: https://www.mdpi.com/2071-1050/12/15/6095/
    Download Restriction: no
    ---><---

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jsusta:v:12:y:2020:i:15:p:6095-:d:391427. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    We have no bibliographic references for this item. You can help adding them by using this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.