IDEAS home Printed from https://ideas.repec.org/a/gam/jeners/v9y2016i4p239-d66482.html
   My bibliography  Save this article

Development of an ICE-Based Micro-CHP System Based on a Stirling Engine; Methodology for a Comparative Study of its Performance and Sensitivity Analysis in Recreational Sailing Boats in Different European Climates

Author

Listed:
  • Guillermo Rey

    (Defense University Center, Naval Academy, Marín 36920, Spain)

  • Carlos Ulloa

    (Defense University Center, Naval Academy, Marín 36920, Spain)

  • Jose Luis Míguez

    (ETS Ingenieros Industriales, University of Vigo, Vigo 36310, Spain)

  • Elena Arce

    (Defense University Center, Naval Academy, Marín 36920, Spain)

Abstract

Micro combined heating and power (micro-CHP) systems are becoming more than important, and even essential, if we pretend to take full advantage of available energy. The efficiency of this kind of systems reaches 90% and important savings in energy transport processes can occur. In this research, an internal combustion engine (ICE)-based micro-CHP system was developed and tested under specific constraints. The system uses a two cylinder Otto engine as prime mover, coupled to an electrical alternator, and it uses exhaust gases and engine cooling circuit heat. The micro-CHP system was developed to match the electrical power of a typical Stirling engine (SE)-based micro-CHP unit, in order to later compare both systems’ performance under similar circumstances. Different operating modes were tested under different engine speeds, in order to find the optimum operating point. A stand-alone portable application of this system was performed using recreational sailing boats as mobile homes. Specific considerations had to be taken, related to boundary conditions with sea water, and a transient simulation was performed, considering the boat under three different European climates. Results were compared for the different locations and the performance of the equipment shown. A comparative study with the SE-based micro-CHP system performance was done, and a sensitivity analysis of the influence of the battery size was carried out under the same conditions. The SE and ICE-based proposed micro-CHP system have similar behavior, except for the differences found due to the electric/thermal power ratios in both systems. Battery bank size sensitivity analysis reflects a limit in performance improvement. This limit is caused by the uniform distribution of electrical demand profile.

Suggested Citation

  • Guillermo Rey & Carlos Ulloa & Jose Luis Míguez & Elena Arce, 2016. "Development of an ICE-Based Micro-CHP System Based on a Stirling Engine; Methodology for a Comparative Study of its Performance and Sensitivity Analysis in Recreational Sailing Boats in Different Euro," Energies, MDPI, vol. 9(4), pages 1-14, March.
    • Handle: RePEc:gam:jeners:v:9:y:2016:i:4:p:239-:d:66482
    as

    Download full text from publisher

    File URL: https://www.mdpi.com/1996-1073/9/4/239/pdf
    Download Restriction: no
    File URL: https://www.mdpi.com/1996-1073/9/4/239/
    Download Restriction: no
    ---><---

    References listed on IDEAS

    as
    1. Carlos Ulloa & Jacobo Porteiro & Pablo Eguía & José M. Pousada-Carballo, 2013. "Application Model for a Stirling Engine Micro-Generation System in Caravans in Different European Locations," Energies, MDPI, vol. 6(2), pages 1-16, February.
    2. Stathopoulos, P. & Paschereit, C.O., 2015. "Retrofitting micro gas turbines for wet operation. A way to increase operational flexibility in distributed CHP plants," Applied Energy, Elsevier, vol. 154(C), pages 438-446.
    3. Ren, Hongbo & Gao, Weijun & Zhou, Weisheng & Nakagami, Ken'ichi, 2009. "Multi-criteria evaluation for the optimal adoption of distributed residential energy systems in Japan," Energy Policy, Elsevier, vol. 37(12), pages 5484-5493, December.
    4. Onovwiona, H.I. & Ugursal, V.I., 2006. "Residential cogeneration systems: review of the current technology," Renewable and Sustainable Energy Reviews, Elsevier, vol. 10(5), pages 389-431, October.
    5. Lozano, Miguel A. & Ramos, Jose C. & Serra, Luis M., 2010. "Cost optimization of the design of CHCP (combined heat, cooling and power) systems under legal constraints," Energy, Elsevier, vol. 35(2), pages 794-805.
    6. Campos Celador, A. & Erkoreka, A. & Martin Escudero, K. & Sala, J.M., 2011. "Feasibility of small-scale gas engine-based residential cogeneration in Spain," Energy Policy, Elsevier, vol. 39(6), pages 3813-3821, June.
    7. Mirko Grljušić & Vladimir Medica & Gojmir Radica, 2015. "Calculation of Efficiencies of a Ship Power Plant Operating with Waste Heat Recovery through Combined Heat and Power Production," Energies, MDPI, vol. 8(5), pages 1-27, May.
    8. Barbieri, Enrico Saverio & Melino, Francesco & Morini, Mirko, 2012. "Influence of the thermal energy storage on the profitability of micro-CHP systems for residential building applications," Applied Energy, Elsevier, vol. 97(C), pages 714-722.
    9. TeymouriHamzehkolaei, Fatemeh & Sattari, Sourena, 2011. "Technical and economic feasibility study of using Micro CHP in the different climate zones of Iran," Energy, Elsevier, vol. 36(8), pages 4790-4798.
    10. Ghasemi, Abolfazl & Asrari, Arash & Zarif, Mahdi & Abdelwahed, Sherif, 2013. "Techno-economic analysis of stand-alone hybrid photovoltaic–diesel–battery systems for rural electrification in eastern part of Iran—A step toward sustainable rural development," Renewable and Sustainable Energy Reviews, Elsevier, vol. 28(C), pages 456-462.
    11. Comodi, Gabriele & Cioccolanti, Luca & Renzi, Massimiliano, 2014. "Modelling the Italian household sector at the municipal scale: Micro-CHP, renewables and energy efficiency," Energy, Elsevier, vol. 68(C), pages 92-103.
    12. Gabriele Battista & Luca Evangelisti & Claudia Guattari & Carmine Basilicata & Roberto De Lieto Vollaro, 2014. "Buildings Energy Efficiency: Interventions Analysis under a Smart Cities Approach," Sustainability, MDPI, vol. 6(8), pages 1-12, July.
    13. Barbieri, Enrico Saverio & Spina, Pier Ruggero & Venturini, Mauro, 2012. "Analysis of innovative micro-CHP systems to meet household energy demands," Applied Energy, Elsevier, vol. 97(C), pages 723-733.
    14. Merkel, Erik & McKenna, Russell & Fichtner, Wolf, 2015. "Optimisation of the capacity and the dispatch of decentralised micro-CHP systems: A case study for the UK," Applied Energy, Elsevier, vol. 140(C), pages 120-134.
    15. Peacock, A.D. & Newborough, M., 2006. "Impact of micro-combined heat-and-power systems on energy flows in the UK electricity supply industry," Energy, Elsevier, vol. 31(12), pages 1804-1818.
    16. Matteo Zago & Andrea Casalegno & Renzo Marchesi & Fabio Rinaldi, 2011. "Efficiency Analysis of Independent and Centralized Heating Systems for Residential Buildings in Northern Italy," Energies, MDPI, vol. 4(11), pages 1-17, November.
    17. Monteiro, Eliseu & Moreira, Nuno Afonso & Ferreira, Sérgio, 2009. "Planning of micro-combined heat and power systems in the Portuguese scenario," Applied Energy, Elsevier, vol. 86(3), pages 290-298, March.
    18. Chesi, Andrea & Ferrara, Giovanni & Ferrari, Lorenzo & Magnani, Sandro & Tarani, Fabio, 2013. "Influence of the heat storage size on the plant performance in a Smart User case study," Applied Energy, Elsevier, vol. 112(C), pages 1454-1465.
    19. Mirko Grljušić & Vladimir Medica & Nikola Račić, 2014. "Thermodynamic Analysis of a Ship Power Plant Operating with Waste Heat Recovery through Combined Heat and Power Production," Energies, MDPI, vol. 7(11), pages 1-27, November.
    20. Campos-Celador, Álvaro & Pérez-Iribarren, Estibaliz & Sala, José María & del Portillo-Valdés, Luis Alfonso, 2012. "Thermoeconomic analysis of a micro-CHP installation in a tertiary sector building through dynamic simulation," Energy, Elsevier, vol. 45(1), pages 228-236.
    Full references (including those not matched with items on IDEAS)

    Citations

    Citations are extracted by the CitEc Project, subscribe to its RSS feed for this item.
    as


    Cited by:

    1. Yeongmin Kim & Wongee Chun & Kuan Chen, 2017. "Thermal-Flow Analysis of a Simple LTD (Low-Temperature-Differential) Heat Engine," Energies, MDPI, vol. 10(4), pages 1-16, April.
    2. Francesco Calise & Massimo Dentice D’Accadia, 2016. "Simulation of Polygeneration Systems," Energies, MDPI, vol. 9(11), pages 1-9, November.
    3. Jose Egas & Don M. Clucas, 2018. "Stirling Engine Configuration Selection," Energies, MDPI, vol. 11(3), pages 1-22, March.
    4. Calise, Francesco & de Notaristefani di Vastogirardi, Giulio & Dentice d'Accadia, Massimo & Vicidomini, Maria, 2018. "Simulation of polygeneration systems," Energy, Elsevier, vol. 163(C), pages 290-337.

    Most related items

    These are the items that most often cite the same works as this one and are cited by the same works as this one.
    1. González-Pino, I. & Pérez-Iribarren, E. & Campos-Celador, A. & Las-Heras-Casas, J. & Sala, J.M., 2015. "Influence of the regulation framework on the feasibility of a Stirling engine-based residential micro-CHP installation," Energy, Elsevier, vol. 84(C), pages 575-588.
    2. Romero Rodríguez, Laura & Salmerón Lissén, José Manuel & Sánchez Ramos, José & Rodríguez Jara, Enrique Ángel & Álvarez Domínguez, Servando, 2016. "Analysis of the economic feasibility and reduction of a building’s energy consumption and emissions when integrating hybrid solar thermal/PV/micro-CHP systems," Applied Energy, Elsevier, vol. 165(C), pages 828-838.
    3. Maghanki, Maryam Mohammadi & Ghobadian, Barat & Najafi, Gholamhassan & Galogah, Reza Janzadeh, 2013. "Micro combined heat and power (MCHP) technologies and applications," Renewable and Sustainable Energy Reviews, Elsevier, vol. 28(C), pages 510-524.
    4. Guillermo Rey & Carlos Ulloa & José Luís Míguez & Antón Cacabelos, 2016. "Suitability Assessment of an ICE-Based Micro-CCHP Unit in Different Spanish Climatic Zones: Application of an Experimental Model in Transient Simulation," Energies, MDPI, vol. 9(11), pages 1-13, November.
    5. Murugan, S. & Horák, Bohumil, 2016. "A review of micro combined heat and power systems for residential applications," Renewable and Sustainable Energy Reviews, Elsevier, vol. 64(C), pages 144-162.
    6. Chesi, Andrea & Ferrara, Giovanni & Ferrari, Lorenzo & Magnani, Sandro & Tarani, Fabio, 2013. "Influence of the heat storage size on the plant performance in a Smart User case study," Applied Energy, Elsevier, vol. 112(C), pages 1454-1465.
    7. Barbieri, Enrico Saverio & Melino, Francesco & Morini, Mirko, 2012. "Influence of the thermal energy storage on the profitability of micro-CHP systems for residential building applications," Applied Energy, Elsevier, vol. 97(C), pages 714-722.
    8. Schütz, Thomas & Schraven, Markus Hans & Remy, Sebastian & Granacher, Julia & Kemetmüller, Dominik & Fuchs, Marcus & Müller, Dirk, 2017. "Optimal design of energy conversion units for residential buildings considering German market conditions," Energy, Elsevier, vol. 139(C), pages 895-915.
    9. Lombardi, K. & Ugursal, V.I. & Beausoleil-Morrison, I., 2010. "Proposed improvements to a model for characterizing the electrical and thermal energy performance of Stirling engine micro-cogeneration devices based upon experimental observations," Applied Energy, Elsevier, vol. 87(10), pages 3271-3282, October.
    10. Mohammadi, Mohammad & Noorollahi, Younes & Mohammadi-ivatloo, Behnam & Yousefi, Hossein, 2017. "Energy hub: From a model to a concept – A review," Renewable and Sustainable Energy Reviews, Elsevier, vol. 80(C), pages 1512-1527.
    11. Asensio, F.J. & San Martín, J.I. & Zamora, I. & Oñederra, O., 2018. "Model for optimal management of the cooling system of a fuel cell-based combined heat and power system for developing optimization control strategies," Applied Energy, Elsevier, vol. 211(C), pages 413-430.
    12. Mongibello, Luigi & Bianco, Nicola & Caliano, Martina & Graditi, Giorgio, 2016. "Comparison between two different operation strategies for a heat-driven residential natural gas-fired CHP system: Heat dumping vs. load partialization," Applied Energy, Elsevier, vol. 184(C), pages 55-67.
    13. Adam, Alexandros & Fraga, Eric S. & Brett, Dan J.L., 2015. "Options for residential building services design using fuel cell based micro-CHP and the potential for heat integration," Applied Energy, Elsevier, vol. 138(C), pages 685-694.
    14. Mongibello, Luigi & Bianco, Nicola & Caliano, Martina & Graditi, Giorgio, 2015. "Influence of heat dumping on the operation of residential micro-CHP systems," Applied Energy, Elsevier, vol. 160(C), pages 206-220.
    15. González-Pino, I. & Pérez-Iribarren, E. & Campos-Celador, A. & Terés-Zubiaga, J., 2020. "Analysis of the integration of micro-cogeneration units in space heating and domestic hot water plants," Energy, Elsevier, vol. 200(C).
    16. Pérez-Iribarren, E. & González-Pino, I. & Azkorra-Larrinaga, Z. & Gómez-Arriarán, I., 2020. "Optimal design and operation of thermal energy storage systems in micro-cogeneration plants," Applied Energy, Elsevier, vol. 265(C).
    17. Marguerite, C. & Andresen, G.B. & Dahl, M., 2018. "Multi-criteria analysis of storages integration and operation solutions into the district heating network of Aarhus – A simulation case study," Energy, Elsevier, vol. 158(C), pages 81-88.
    18. Kopanos, Georgios M. & Georgiadis, Michael C. & Pistikopoulos, Efstratios N., 2013. "Energy production planning of a network of micro combined heat and power generators," Applied Energy, Elsevier, vol. 102(C), pages 1522-1534.
    19. Haupt, Axel & Müller, Karsten, 2017. "Integration of a LOHC storage into a heat-controlled CHP system," Energy, Elsevier, vol. 118(C), pages 1123-1130.
    20. González, Arnau & Riba, Jordi-Roger & Puig, Rita & Navarro, Pere, 2015. "Review of micro- and small-scale technologies to produce electricity and heat from Mediterranean forests׳ wood chips," Renewable and Sustainable Energy Reviews, Elsevier, vol. 43(C), pages 143-155.

    Corrections

    All material on this site has been provided by the respective publishers and authors. You can help correct errors and omissions. When requesting a correction, please mention this item's handle: RePEc:gam:jeners:v:9:y:2016:i:4:p:239-:d:66482. See general information about how to correct material in RePEc.

    If you have authored this item and are not yet registered with RePEc, we encourage you to do it here. This allows to link your profile to this item. It also allows you to accept potential citations to this item that we are uncertain about.

    If CitEc recognized a bibliographic reference but did not link an item in RePEc to it, you can help with this form .

    If you know of missing items citing this one, you can help us creating those links by adding the relevant references in the same way as above, for each refering item. If you are a registered author of this item, you may also want to check the "citations" tab in your RePEc Author Service profile, as there may be some citations waiting for confirmation.

    For technical questions regarding this item, or to correct its authors, title, abstract, bibliographic or download information, contact: MDPI Indexing Manager (email available below). General contact details of provider: https://www.mdpi.com .

    Please note that corrections may take a couple of weeks to filter through the various RePEc services.

    IDEAS is a RePEc service. RePEc uses bibliographic data supplied by the respective publishers.